Linn-CardrigdeService-sm 维修电路原理图.pdf

《Linn-CardrigdeService-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Linn-CardrigdeService-sm 维修电路原理图.pdf（12页珍藏版）》请在收音机爱好者资料库上搜索。

1、REPLACEMENT OF A LINN MOVING COIL CARTRIDGEIMPORTANT NOTE:Please do not attempt this work without expert professional assistance or the appropriate skills and qualifications. Linn retailers are allhighly trained and would be happy to do this work on your behalf. Linn cannot be held liable for any in

2、jury or damage. This informationis provided for reference only and does not imply any acceptance of responsibility for any injury.INSTRUCTIONSThe cartridge you are about to remove is worn out or broken but the LP12 and the Arm are still in perfect condition and I am sure that youwould like them to r

3、emain that way, so please read through the instructions carefully before proceeding.INDEXPage Contents.2. How to remove your Linn Tonearm from your Linn LP12.5. How to remove your Linn Cartridge from your Linn Tonearm.6. How to pack your Linn Cartridge.7. How to fit your Linn Cartridge to your Linn

4、Tonearm.9. How to fit and align your Linn Tonearm and CartridgeTOOLS YOU WILL REQUIRE. - 5 mm spanner- Set of Metric Allen (hex) keys- No 1 Pozi-drive Screwdriver- Small needle nose pliers- Alignment protractor. See page 12. You can print this off, but check that your printer has retained thecorrect

5、 scale before use!WARNING: Always disconnect the product from the mains and from other products connected to the mainsbefore carrying out any adjustmentsRadioFans.CN 收音机爱 好者资料库1. Switch off your amplifier before you unplug anything!Then disconnect the turntable from everythingESPECIALLY MAINS!* See

6、Warning on Cover Page.Fit stylus guard and lift off outer platter. 2. Remove the belt and store it safely. Lift up the innerplatter a few inches and place a couple of paperback booksunder the inner platter to protect the bearing- do notremove the inner platter as oil could be lost and dirt couldente

7、r the bearing housing.3. With the Turntable placed on some books.4. . . or over the edge of a table,remove all the base screws and feet.How to remove your Linn Tonearm from your Linn LP 12RadioFans.CN 收音机爱 好者资料库Page 35. Using the 1.5 Allen (hex) key (early arms used 1.27 mm)loosen the arm plug locki

8、ng grub screw at the bottom ofthe arm by tilting the turntable slightly.56. Or if the turntable is raised on books, dont tilt theturntable but locate and loosen the grub screw.7. Unplug the arm cable from the bottom of the arm.How to remove your Linn Tonearm from your Linn LP 128. Supporting the Ton

9、earm as shown loosen the grubscrew with 4 mm Allen (hex) key and remove fromturntable. With the Ittok LVII, first un-clip from the armrest and, supporting as shown, lift clear of the turntable.How to remove your Linn Tonearm from your Linn LP 128. Holding the Tonearm by the arm tube, remove thecount

10、erweight by turning and pulling gently. Place theCounterweight in a safe place.Proceed to next step:“How to remove Your Linn Cartridge from your LinnTonearm”.Page 5How to remove your Linn Cartridge from your Linn Tonearm2. Place the arm over the edge of a clean table and loosenthe mounting screws wi

11、th a 2.5 mm Allen (hex) key. Thiswill avoid stressing the bearings.3. Hold the 5 mm spanner as shown to prevent the nutsfrom turning and remove all the cartridge bolts. Keep thenuts and bolts safe- you may need to reuse them.1. If your arm is an Ittok, use a rubber band to secure thearm to the lift

12、lower platform. This will help protect thedelicate bearings should you handle the arm roughly.4. Now carefully remove the tags using a small pair of longnose pliers. Place the arm in a safe place, safest place isback on your LP12!Proceed to next page for packing instructions.How to Pack your cartrid

13、ge.1.Take the cartridge and place in original jewellery box. If you do not have one place in small box withpacking wrapped round the cartridge e.g. old film container with paper tissues.2.Place in a padded envelope or small box with more packing.3.Complete the returns order form.4.Return to :America

14、n CustomersAll Other Customers WorldwideLinn Inc. (Cartridge Rebuilds Offer)Linn Products Ltd. (Cartridge Rebuilds Offer)PO Box 455Floors RoadPompton PlainsWaterfootNJ 07444GlasgowG76 0EP5.Please send registered mail or equivalent.Linn Products cannot take responsibility for any cartridges missing o

15、r damaged intransit, so please ensure that you have packed it securely and have insured it againstloss.Page 7How to fit your Linn Cartridge to your Linn TonearmTaking the old cartridge off was fairly painless. The new one is perfect and worth a lot of money.Please keep the stylus guard on at all tim

16、es and only remove when aligning on the record.If you get stuck, or are unsure on how to proceed please contact your retailer or drop us an e-mail or fax and we will do all we can to help you.2. Note the colours of the wires as shown above if tagsare already fitted.1. Unpack the cartridge and remove

17、 from box. Fit the tagsto the cartridge if required as shown above.4. .carefully fit the tags to the arm.How to fit your Linn Cartridge to your Linn Tonearm5. Line up the cartridge with the cursor line on the headshell. (This is on theEkos only and helps with the setup but the following alignment ga

18、uge willalso suffice). Fit the screws and nuts finger tight as alignment still has to beconfirmed. Retain the cartridge box in a safe place for future use.3. Using the colour codes as shown: 1. left hot (+) = white2. right hot (+) = red 3. left earth (-) = blue4. right earth (-) = greenPage 9How to

19、fit and align your Linn Tonearm and Cartridge1. Once the cartridge is fitted to the arm, refit the counterweight to the arm by pushing it on to the tail piece bevellededge first whilst turning the counterweight. TIP: Use a sliverof soap to moisten the tail of the arm tube to make thiseasier.2. Refit

20、 the Tonearm to the turntable and tighten at theapproximate height. Turn tracking and Bias dial to 0. Seepoint 4 below.WARNING:Turn tracking dial slowly and do not go past 0.4. Clip the arm in the arm rest and add tracking weight by dialling 1.7on the tracking force dial (A). Dial B is the Bias or ”

21、 anti-skate” Dial.3. Remove the stylus guard and un-clip the arm from the rest,then move the counter weight back and forth in small steps untilarm floats horizontally, i.e. is balanced or “calibrated”. TAKE CAREAS THE STYLUS GUARD IS OFF!.(A)(B)7. Rotate the platter by hand as required to enable pla

22、cement of styluson cross-hair (A) so lines are parallel to the cartridge body. Lift thestylus off the protractor while moving the platter. Adjust the Cartridge ifnecessary forward or back on the headshell ensuring Cartridge remainsparallel in the headshell. The outside edge of the headshell (nearest

23、finger lift) will also be parallel so you can use this to line up withprotractor. Confirm alignment at point B.8. Once you are satisfied that the cartridge is alignedremove the arm from your turntable and tighten cartridgescrews in position until Allen (hex) key starts to bend.Use spanner to hold th

24、e nuts in place and stop themturning . Refit arm and make final check of alignment(see point 5). When finished place arm in arm clip.5. Place Arm on record and adjust height until horizontal.If arm is too high or too low, place arm back in clip andadjust the arm height. Repeat this procedure until a

25、rm ishorizontal. Tip: Use reflection on record and adjust untilarm-tube is parallel with its reflection.How to fit and align your Linn Tonearm and Cartridge6. Place alignment protractor on the record.Page 1111. Check that the cable does not touch ANYTHING and is clear of the base.12. Remove outer pl

26、atter. Refit the turntable base andreinstall the turntable in its playing location.Connect the audio and power leads.Refit the belt and outer platter.Happy listening!How to fit and align your Linn Tonearm and Cartridge9.Tighten the arm in place- use the 4mm Allen (hex) keyas shown to avoid overtigtn

27、ing.-WARNING: Overtightning this height locking screw willdamage the arm bearings.10. Refit the arm plug as shown. Tighten securing grubscrew but do not over-tighten.? ? ? ? ?Alignment Protractor:1. Print off.2. Check that the scale has been retained with by measuring with a ruler.3. Past on to thin card.4. Cut around the border5. Carefully cut out the spindle hole with a craft knife or scalpel. Please wear safety goggles!6. Your alignment protractor is ready for use.