Infinity-Overture3-sub-sm 维修电路原理图.pdf
《Infinity-Overture3-sub-sm 维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《Infinity-Overture3-sub-sm 维修电路原理图.pdf(36页珍藏版)》请在收音机爱好者资料库上搜索。
1、Compositions SeriesOverture 3Powered LoudspeakersService ManualInfinity Systems, Inc250 Crossways Park Dr.Woodbury, New York 11797Rev1 5/2004RadioFans.CN 收音机爱 好者资料库TABLE OF CONTENTS SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 DETAILED SPECIFICATIONS .
2、. . . . . . . . . . . . . . . . . . . . . . . . . . .4 WIRING THE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 OPERATING THE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 REPLACING THE FUSE . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3、 . . . . .7 CARE OF YOUR SPEAKER SYSTEM/TROUBLESHOOTING . . .10 MECHANICAL/PACKAGING PARTS LIST . . . . . . .11 EXPLODED VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 PACKAGING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 SERVICE BU
4、LLETIN INF9704 NOV. 1997 .14 SERVICE BULLETIN INF9705 NOV. 1997 . . . . . . . . . . . . . . .16 SERVICE BULLETIN INF9802 JUNE 1998. . . . . . . . . . . . . . .17 TEST SET UP AND PROCEDURE . . . . . . . . .18 NOTE ON OVTR 2/3 AMPLIFIER REVISION.19 PCB DRAWINGS . . . . . . . . . . . . . . . . . . . .
5、. . . . . . . . . . . . . . . . . .20 ELECTRICAL PARTS LIST (120V) . . . . . . . . . . . . . . . .22 ELECTRICAL PARTS LIST (230V) . . . . . . . . . . . . . . . . . . . . . . . . . .25 INTEGRATED CIRCUIT DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . .28 WIRING DIAGRAM/CROSSOVER NETWORK SCHEM
6、ATIC (120V) . . .29 WIRING DIAGRAM/CROSSOVER NETWORK SCHEMATIC (230V) . . .30 120V SCHEMATICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 230V SCHEMATICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Infinity continually strives to update
7、 and improve existing products, as well as create new ones. The specifications and construction details in this and related Infinity publications are therefore subject to change without notice. Overture 3 2RadioFans.CN 收音机爱 好者资料库Overture 33SpecificationsOverture 3 Frequency Response: 25Hz - 20,000Hz
8、 (3dB)Recommended Amplifier Power Range 10-200 watts*Amplifier Peak Output:500VAMaximum Output:115 dB SPLSensitivity:94 dB 2.83V 1 meterNominal Impedance:8Crossover Frequencies:350 and 3,000HzLow-Frequency Driver:(4) 6-1/2” (165mm) high efficiency,dynamically balanced, magneticallyshielded woofers.M
9、idrange Driver:(2) 5-1/4” (125mm) high-efficiency,magnetically shielded midrange drivers.High-Frequency Driver:(1) 1” (25mm) soft dome, high-efficiency, neodymium magnet,magnetically shielded tweeter.Dimensions (H x W x D):46 x 6-7/8 x 15-3/4(1,168mm x 175mm x 400mm)Weight:59 lb/(26.8 kg)Power Consu
10、mption:300 watts (Maximum)* The maximum recommended amplifier power rating will ensure proper system headroom to allowfor occasional peaks. We do not recommend sustained operation at these maximum power levels.Detailed SpecificationsOverture 34Overture 35Wiring The SystemOverture 36Operating The Sys
11、temOverture 37Operating The System/Replacing The FuseOverture 38Replacing the Fuse (Cont.)Overture 39Replacing The Fuse (Cont.)UTILSER UN FUSIBLE DE RECHANGE DE MEME TYPE ET CALIBREFOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE OF FUSE: T1.6A 250VCAUTION:ATTENTION:POWERFU
12、SET 1.6A 250V 230V 50Hz150W MAX00435FUSEFUSEFUSE T3, 1.6A 250VOVTR 2 & 3 FUSEOverture 310TroubleshootingOverture 311Mechanical Parts ListRef No.DescriptionQtyPart No.1CABINETNOT FOR SALE26.5”, WOOFER, B160-4 (120V) DCR = 14.210%4330618-0016.5”, WOOFER, LM-B160-8 (230V) DCR = 4010%4333773-0013SCREW,
13、#8 x .75”, PPH, ZINC25900102-0124REAR WOOFER GRILLE2330955-0015FRONT/REAR WOOFER BAFFLE4332334-0016AMPLIFIER CAP1331399-0017CROSSOVER NETWORK (120V)1334416-0018BASE, FRONT FOOT1331184-0019REAR BASE1331075-00210REAR BASE w/PORT1331236-00111BINDING POST (RED)1331723-00112BINDING POST (BLACK)1331724-00
14、113SCREW, #8 x 1” PPH, ZINC15900102-01614SCREW, #6-32 x 3/8” PPHMS CADCAD PLATED21081115AMPLIFIER1NOT FOR SALE161” (25MM) NEODYMIUM TWEETER DCR = 3.610%1333232-00117UPPER FRONT BAFFLE (120V)1331182-001UPPER FRONT BAFFLE (230V)1332335-00218FRONT GRILLE1333584-00119SCREW, #6 x 3/4” PPHD, BLK206356320S
15、CREW, 4-40 x .25” PPH, ZINC2905502-004215.25”,MIDRANGE TRANSDUCER, B125-6 DCR = 7.710%2330650-00122MIDRANGE CUP (120V)1330833-00123HI-FREQ. TWEETER GASKET1331725-001PACKAGING24SPIKE FOOT SET, 1.5”1331360-00125OUTER CARTON (120V)1331246-00126FOAM PAD, TOP1331254-00127FOAM PAD, BOTTOM1331255-00128SURV
16、EY CARD1330033-00129OWNERS MANUAL (120V)1332293-00130SAFETY SHEET1330100-00131LINE FUSE 5A 2AG SLO-BLO (120V)2FS1068 or 331925-001Overture 312Exploded View1234519432781011121313142156351918191716321202290043723Overture 313PackagingOverture 314Overture 315Overture 316Overture 317Overture 318Test Set
17、Up and ProcedureSIGNALGENERATORAMPLIFIERAC VOLTMETER (10V)OVERTURE 3UNDER TESTSPEAKEROUTPUTFROMAMPLIFIER00421SYSTEM AURAL SWEEP TESTEquipment needed:Function/signal generator/sweep generatorHigh Gain Integrated AmplifierMultimeterSpeaker cablesGeneral Unit Function (UUT = Unit Under Test)1.From the
18、signal generator, connect a mono cable to the Integrated amplifier; with speaker cables connect the amplifiersoutput to the UUT Speaker binding posts.2.On the UUT, turn the BASS (level) control full counterclockwise (1).3.Turn on generator, adjust so that the output at the Integrated amplifier is 2.
19、0V, 40 Hz.4.Plug in UUT; LED should be Red. Turn BASS (level) control full clockwise (9).5.LED should now be Green and immediate bass response should be heard (and observed if the grille is removed).Sweep Function6.Follow steps 1-5 above.7.Sweep generator from 20Hz to 300Hz. Listen to the cabinet an
20、d drivers for any rattles, clicks, buzzes or any other noises. Ifany unusual noises are heard, remove woofers and test.Driver Function8.Remove woofer from cabinet; detach + and - wire clips.9.Check DC resistance of woofer; it should be:(120v) - 14.2 Ohms 10%(230v) - 40.0 Ohms 10%10. Connect a pair o
21、f speaker cables to driver terminals. Cables should be connected to a high-gain integratedamplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 20.0V. * 11. Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual nois
22、es.* Only the 120v version will be driven to near maximum excursion at this voltage; because of the unusually high DCR of the voice coil,driving the 230v version at twice this voltage is not practical with simple test equipment and 20v should suffice for test purposes.Amplifier bias adjustment1)Powe
23、r up loudspeaker and drive at low levels for 3 minutes for warm-up.2)Remove amplifier assembly (disassembly procedure in bulletin INF9704 Page 15).3)Power up on the bench; attach DMM (on low DC voltage range) across TP1 and TP2 on schematic R77 - (120v) .22 5Wfuse resistor. (230v) .47 5W fuse resist
24、or. Mini-grabbers can be used on the resistor leads without PCB removal.4)Adjust POT2 (bias pot on PCB) to read 5.9 mV for both 120v and 230v units.IMPORTANT NOTE ON OVTR 2/3 AMPLIFIER REVISION There was an early version of the Overture 2 and 3 Amplifier that is represented slightly inaccurately in
25、the schematic, PCB drawings, and parts list in this service manual. This page is a guide to the identification and differences to this earlier version. The drawing below is a later version of the PCB, complete with this information. NLA = No Longer Available ORIGINAL VERSION = R80 IS NOT IN SILKSCRE
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Infinity-Overture3-sub-sm 维修电路原理图 Infinity Overture3 sub sm 维修 电路 原理图