McIntosh-MC2KW-pwr-smp(1) 维修电路原理图.pdf
《McIntosh-MC2KW-pwr-smp(1) 维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《McIntosh-MC2KW-pwr-smp(1) 维修电路原理图.pdf(28页珍藏版)》请在收音机爱好者资料库上搜索。
1、Performance Specifications . 2Notes MC2KW. 3POWER MODULERear Panel . 3Section Location . 3Block Diagram . 4Interconnection Diagram . 5 - 6Amp Schematic and PCB . 7 - 9Heatsink Schematic and PCB . 10 - 11Heatsink Slave Schematic and PCB . 12 - 13Capacitor Schematic and PCB . 14Logo Schematic and PCB
2、. 15Logo Schematic and PCB . 16Parts List . 17 - 19OUTPUT MODULERear Panel . 20Section Location . 20Interconnection Diagram . 21 - 22Main Schematic and PCB . 23 - 28Meter Power Supply Schematic and PCB. 29 - 32Meter Led Schematic and PCB . 33 - 34Parts List . 35 - 37Repacking Instruction . 39POWERMO
3、DULECONTENTSOUTPUTMODULESERVICE MANUALPOWER AMPLIFIERPRELIMINARYSERIAL NO.POWER MODULE WJ-A001 And AbovePOWER MODULE WJ-B001 And AboveOUTPUT MODULE WJ-C001 And AboveRadioFans.CN 收音机爱 好者资料库PERFORMANCE SPECIFICATIONSPower Output2000 watts into an 8, 4 or 2 ohm load is the minimum sinewave continuous a
4、verage power output. The output RMSvoltage is:126.5V across 8 ohms89.5V across 4 ohms62.2V across 2 ohmsOutput Load Impedance8, 4 and 2 ohms (with three paors of terminals each forimpedance)Rated Power Band20Hz to 20,000HzTotal Harmonic Distortion0.005% maximum harmonic distortion at any power level
5、 from250 milliwatts to 2000 watts, 20Hz to 20,000HzDynamic Headroom2dBFrequency Response+0, -0.25dB from 20Hz to 20,000Hz+0, -3dB from 10Hz to 100,000HzSensitivity5.0 Volts Balanced Input2.5 Volts Unbalanced InputA-Weighted Signal To Noise Ratio90dB Unbalanced (123dB below rated output)94dB Balanced
6、 (127dB below rated output)Intermodulation Distortion0.005% maximum, if instantaneous peak power output doesnot exceed 4000 watts, for any combination of frequenciesfrom 20Hz to 20kHz.Wide Band Damping FactorGreater than 40Input Impedance10,000 ohmsPower GuardLess than 2% THD with up to 14dB overdri
7、veGeneral SpecificationsMC2KW Output Module Power Requirements100 Volts, 50/60Hz at 35 watts110 Volts, 50/60Hz at 35 watts120 Volts, 50/60Hz at 35 watts220 Volts, 50/60Hz at 35 watts230 Volts, 50/60Hz at 35 watts240 Volts, 50/60Hz at 35 wattsMC2KW Power Module Power Requirements1100 Volts, 50/60Hz a
8、t 1440 watts110 Volts, 50/60Hz at 13.0 amps120 Volts, 50/60Hz at 12 amps220 Volts, 50/60Hz at 7.5 amps230 Volts, 50/60Hz at 6.5 amps240 Volts, 50/60Hz at 6.5 ampsNote: Refer to the rear panels of the MC2KW Output Module andMC2KW Power Modules for the correct voltage.Overall DimensionsMC2KW Output Mo
9、dule: Width is 17-3/4 inches (45.09cm),Height us 12-5/16 inches (31.27cm) including feet, Depth is 26-5/8 inches (62.54cm) including the front panel, handles, knobs andinterconnect cables2MC2KW Power Module: Width is 17-3/4 inches (45.09cm),Height us 12-5/16 inches (31.27cm) including feet, Depth is
10、 26-5/8 inches (62.54cm) including the front panel, handles andinterconnect cables2WeightMC2KW Output Module is 121 poulds (54.9kg) net, 146 pounds(66.2kg) in shipping cartonMC2KW Power Module is 158 poulds (71.7kg) net, 183 pounds(83.0kg) in shipping carton1 The power requirements listed are for ea
11、ch MC2KW PowerModule, two are required for each MC2KW Power Amplifier2 Interconnect cables are supplied with the MC2KW OutputModule and both MC2KW Power Modules connect to theMC2KW Output Module.21. The heavy notes on the schematic denote the primarysignal path.2. Unless otherwise noted, all voltage
12、s indicated on theschematics are measured under the following conditions:a. AC input at 120 volts, 50/60Hz.b. All voltages are +/-10% with respect to ground. Ahigh impedance (10 megaohm) voltmeter must be used.3. Unless otherwise specified:a. Resistor values are in ohms.b. Capacitor values are micro
13、farads (uF).c. Inductor values are in microhenries (uH).4. On PC board drawings, Square pad indicates:a. Polarized Capacitors - Positiveb. Diodes - Cathodec. Others - Pin 15. WARNINGParts marked with the symbol have criticalcharacteristics. Use only replacement parts recom-mended by the manufacturer
14、.6. Soft startup procedure for servicing:1. Interconnect output module and power modules2. Connect Output Module to 120VAC3. Connect Power Modules to variac and set theoutput to zero.4. Turn Output Module power switch to on. (This willenergize the power relays in the Power Modules.)5. Gradually adva
15、nce the variac to 120VAC whilemonitoring the AC current.NOTESRadioFans.CN 收音机爱 好者资料库3REAR PANELSECTION LOCATIONTOP VIEW WITH COVER REMOVEDMC2KWPOWER4BLOCK DIAGRAMINTERCONNECTMC2KWOUTPUT56178AMP 050215 SCH2AMP 050215 PCB2910HEATSINK 050216 SCH3AMC2KWPOWER3BHEATSINK 050216 PCB3A11123BHEATSINK SLAVE 05
16、0282 SCH4A 4BJ2R2R5129610J4J6GP2GP3R4R7R1GP1R3J1R6GP4J5R13R15Q11R21R23Q19C10R14Q10R16R20RT1R22Q18C11J3Q9R19R17Q17Q15Q13R12Q8R18Q12Q14Q16TOREDRev.ABLUMASTER HSGRNMC2KWPOWERHEATSINK SLAVE 0502824A 4B134343113434-80VJ6-80VJ680VJ580VJ5GRNREDGP180V-80V-80V-80VJ6J680V80VJ5J5RECT-J2RECT+J1J7J8J9J10J3J4J5J6
17、C167000uFC267000uF+J7J8J10129592J1J3J5J4J9J6J2GP1REDREDGRNGRNREDGRNRev.AREDREDGRNGRN5CAPACITOR 05021714LOGO 0502186AB+15V6B6B22NC15V6B2215V15V15VGREENGREENJ5:2J5:1J5:2J5:115VGREENDS71.65kR4DS51.65kR3GREENDS11.65kR11kR915VJ5:3J5:4J5:3DS21.65kR2GREENGREENLOGO1J2:1LOGO1LOGO1J1:1GREENDS8DS6GREENDS3J2:3J
18、2:215VJ1:4J1:2J1:3DS4MC2KWPOWER15S9B+NCLOGO26AJ2:36AJ2:2D6AJ2:1J5:3J5:1J5:2LOGO 0502186B16PARTS LISTINTERCONNECTT1POWER TRANSFORMER050230D1DIODE BRIDGE RECT070181RT1ASSY THERMISTOR052017RT2ASSY THERMISTOR052017CBCIRCUIT BREAKER 20A 240V088022AMPLIFIER PCB 050215C1CAP MONO 10PF 200V 10%061297C2CAP EL
19、ECT 100UF 25V066447C3CAP MONO .1UF 50V 20%061305C4CAP MONO .1UF 50V 20%061305C5CAP MONO .1UF 50V 20%061305C6CAP ELECT 10UF 50V066445C7CAP ELECT 22UF 100V066506C8CAP MONO .1UF 50V 20%061305C9CAP MONO .1UF 50V 20%061305C10CAP ELECT 10UF 50V066445C11CAP ELECT 100UF 25V066447C12CAP ELECT 10UF 100VDC0664
20、62C13CAP MONO 1PF 100V NPO061319C14CAP ELECT 10UF 100VDC066462C15CAP MONO 220PF 200V 10%061301C16CAP MONO 470PF 100V 10%061302C17CAP MONO 1000PF 50V 10%061303C18CAP MONO 1000PF 50V 10%061303C19CAP MONO 100PF 100V 10%061300C20CAP MONO 100PF 100V 10%061300C21CAP ELECT 220UF 25V066507C22CAP MONO 47PF 2
21、00V 10%061299C23CAP MONO 47PF 200V 10%061299C24CAP MONO 47PF 200V 10%061299C25CAP MONO .1UF 50V 20%061305C26CAP MONO .1UF 50V 20%061305D1DIODE SILICON070047D2DIODE SILICON070047D3DIODE SILICON070047D4DIODE SILICON070047D5DIODE SILICON070047D6DIODE SIL 400 PIV 1.5A070031D7DIODE SIL 400 PIV 1.5A070031
22、D8DIODE SILICON070047D9DIODE SILICON070047D10DIODE SILICON070047J1HDR SHROUDED 2ROW 26PIN V117870J2CONN 3 POS M MTS100 NRML117214J3CONN 8 POS M FRICTION LOCK117275J4CONN 8 POS M FRICTION LOCK117275J5CONN 3 POS M MTS100 NRML117214J6BLADE FASTON W/FEET117708J7BLADE FASTON W/FEET117708J8HEADER 8 PIN MT
23、A-156117717J9HEADER 8 PIN MTA-156117717J10BLADE FASTON W/FEET117708J11BLADE FASTON W/FEET117708J12BLADE FASTON W/FEET117708J13BLADE FASTON W/FEET117708J15CONN 4 PIN117215J16BLADE FASTON W/FEET117708K1RELAY POWER 24VDC/TV-15087042Q1TRANSISTOR PNP132224Q2TRANSISTOR PNP POWER132255Q3TRANSISTOR NPN13222
24、3Q4TRANSISTOR PNP132224Q5TRANSISTOR NPN132223Q6TRANSISTOR PNP132224Q7TRANSISTOR PNP132224Q8TRANSISTOR PNP 2SA1321C132286Q9TRANSISTOR NPN 2SC3334C132285Q10TRANSISTOR N JFET132222Q11TRANSISTOR N JFET132222Q12TRANSISTOR SI NPN 25V132254Q13TRANSISTOR PNP POWER132255Q14TRANSISTOR PNP132224Q15TRANSISTOR N
25、PN132223Q16TRANSISTOR SI NPN 25V132254Q17TRANSISTOR PNP POWER132255Q18TRANSISTOR NPN132223Q19TRANSISTOR PNP132224Q20TRANSISTOR SI NPN 25V132254Q21TRANSISTOR PNP POWER132255Q22TRANSISTOR NPN 2SC3334C132285Q23TRANSISTOR PNP SILICON132172Q24TRANSISTOR PNP 2SA1321C132286Q25TRANSISTOR NPN 2SC3334C132285Q
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- McIntosh-MC2KW-pwr-smp1 维修电路原理图 McIntosh MC2KW pwr smp 维修 电路 原理图