Gemini-PMX80-mix-sm维修电路原理图.pdf
《Gemini-PMX80-mix-sm维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《Gemini-PMX80-mix-sm维修电路原理图.pdf(9页珍藏版)》请在收音机爱好者资料库上搜索。
1、Page 1SERVICE MANUALPMX-80Stereo Preamp MixerCONTENTS:Connections & Operations:.Page 2-4Specifications:.Page 5Parts Lists:.Page 6-8PCBs:.Page 7-9Schematics:.Page 10Gemini Sound Products Corp.120 Clover Place P.O. Box 6928Edison, NJ 08818-6928732-738-9003 (Phone) 732-738-9006 (Fax)RadioFans.CN 收音机爱 好
2、者资料库Page 27611223344558109RadioFans.CN 收音机爱 好者资料库Page 31911122029303323241634252827132122141531322617353618Page 4Connections1. Make sure that the POWER (6) switch is in the OFF position. This unitcomes supplied with a 15 volt AC adaptor. Plug the male pin of theadaptor into the rear panel POWER JACK
3、 (7). Then plug the adaptorinto a proper power source.2. The MASTER OUTPUT (1) jacks are unbalanced and used to connectto your main amplifier.3. The DJ MIC (18) input (found on the front panel) accepts a 1/4connector and balanced and unbalanced microphones.4. On the rear panel are 2 stereo PHONO/LIN
4、E (3, 4) inputs, 1 stereoPHONO (5) input and 1 stereo LINE (2) input. The PHONO/LINESWITCHES (8, 10) enable you to set the (3, 4) inputs to Phono or Line.The phono inputs will accept only turntables with a magnetic cartridge.A GROUND SCREW (9) for you to ground your turntables is located onthe rear
5、panel. The stereo line inputs will accept any line level inputsuch as a CD player, a cassette player, etc.5. Headphones can be plugged into the front panel mounted PHONES(36) jack.Operation1. POWER ON: Once you have made all the equipment connections toyour mixer, press the POWER (6) switch. The pow
6、er will turn on andthe POWER LED (23) will glow RED.2. CHANNEL 1: The GAIN (11), HIGH (12), MID (13), and LOW (14)controls allow you to fully adjust the selected source. Switch # (15)allows you to select either the PHONO 1 (5) or the PHONO 2/LINE 1(4) input. The CHANNEL SLIDE (16) controls the outpu
7、t level of thischannel.3. CHANNEL 2: The GAIN (29), HIGH (30), MID (31), and LOW (32)controls allow you to fully adjust the selected source. Switch # (33)allows you to select either the PHONO 3/LINE 2 (3) or the LINE 3 (2)input. The CHANNEL SLIDE (34) controls the output level of thischannel.4. KILL
8、ING LOW FREQUENCIES: You can use the Kill Feature on eachchannel to remove Low band frequencies to create special effectsand improve your mix. Move the KILL SWITCH (17) down to removethe low band of Channel 1 from your mix. Move the KILL SWITCH(35) down to remove the low band of Channel 2 from your
9、mix.5. CROSSFADER SECTION: The CROSSFADER (27) allows the mixing ofone source into another. The left side of the CROSSFADER (27) isCHANNEL 1 and the right side is CHANNEL 2. The CROSSFADER (27)in your unit is removable and if the need arises can be easily replaced.Crossfader units are available in t
10、hree varieties. Part # RF-45 (whichis identical to the crossfader supplied with the mixer) has a 45 mmtravel from side to side. Part # RF-30 is available with a 30 mm traveldistance. Also available is the PSF-45 with a special curve designedfor scratch mixing. Just purchase one of these crossfader u
11、nits fromyour Gemini dealer and follow these instructions:1. Unscrew the outside FADER PLATE SCREWS (B). Do nottouch the INSIDE SCREWS (C).2. Carefully lift the fader and unplug the CABLE (D).3. Plug the new fader into the cable and place it back in themixer.4. Screw the fader to the mixer.The CROSS
12、FADER CURVE SWITCH (28) allows you to adjust the kindof curve the crossfader has. When the switch is in the left position,the curve is gradual and gentle. When the switch is in the rightposition, the curve is steep and cutting (perfect for scratching). TheCROSSFADER REVERSE SWITCH (26) allows you to
13、 reverse thecrossfader so that CHANNEL 2 is controlled by the left side of thecrossfader and CHANNEL 1 is controlled by the right side of thecrossfader.NONONONONOTETETETETE: When the CRCRCRCRCROSSFOSSFOSSFOSSFOSSFADER REVERSE SWITADER REVERSE SWITADER REVERSE SWITADER REVERSE SWITADER REVERSE SWITCH
14、CHCHCHCH(26) (26) (26) (26) (26) is activated (moved to the right), only the crossfaderreverses. The Channel Slides, Gain, Kill Switches and tonalcontrols do not reverse.6. OUTPUT CONTROL SECTION: The level of the MASTER OUTPUT (1) iscontrolled by the MASTER (21) control.7. TALKOVER SECTION: The pur
15、pose of the talkover section is to allowthe program playing to be muted so that the mic can be heard abovethe music. The MIC/TALKOVER (19) switch has three settings. Whenthe MIC/TALKOVER (19) switch is in the left position, the mic andtalkover are both off. When the MIC/TALKOVER (19) switch is in th
16、ecenter position the mic is on, the MIC INDICATOR will glow, buttalkover is off. When the MIC/TALKOVER (19) switch is in the rightposition, the mic and talkover will be on and the volume of all sourcesexcept the Mic input are lowered by 16 dB. MIC LEVEL (20) controlsthe level of the MIC.8. CUE SECTI
17、ON: By connecting a set of headphones to the PHONES(36) jack, you can monitor either channel or both together. Move theCUE SWITCH (25) to the left to monitor CHANNEL 1. Move the CUESWITCH (25) to the right to monitor CHANNEL 2. Move the CUESWITCH (25) to the center position to split the signals from
18、 eachchannel so that CHANNEL 1 will be heard in one earphone andCHANNEL 2 will be heard in the other earphone. Use the CUE LEVEL(22) control to adjust the headphone volume without effecting theoverall mix.9. DISPLAY: The DISPLAY (24) indicates the MASTER output.SpecificationsINPUTS:DJ Mic.1.5mV 600
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Gemini PMX80 mix sm 维修 电路 原理图