Pioneer-VSX1016TXVK-avr-sm 维修电路原理图.pdf
《Pioneer-VSX1016TXVK-avr-sm 维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《Pioneer-VSX1016TXVK-avr-sm 维修电路原理图.pdf(250页珍藏版)》请在收音机爱好者资料库上搜索。
1、 ORDER NO.PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, JapanPIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, BelgiumPIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Si
2、ngapore 159936 PIONEER CORPORATION 2006 VSX-1016V-K RRV3401 AUDIO/VIDEO MULTI-CHANNEL RECEIVER VSX-1016V-K VSX-1016V-SVSX-1016TXV-KVSX-80TXVVSX-80TXV-S THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S). ModelTypePower RequirementRemarks VSX-1016V-KHYXJ5AC 220 V to 230 VVSX-1016V-SHYXJ5
3、AC 220 V to 230 VVSX-1016TXV-KKUXJAC 120 VVSX-80TXVKUXJCAAC 120 VVSX-80TXV-SKUXJCAAC 120 VFor details, refer to Important Check Points for good servicing. T-IZS SEPT. 2006 printed in JapanRadioFans.CN 收音机爱 好者资料库 VSX-1016V-K212341234CDFABE SAFETY INFORMATION1. SAFETY PRECAUTIONS The following check s
4、hould be performed for the continued protection of the customer and service technician.LEAKAGE CURRENT CHECK Measure leakage current to a known earth ground (water pipe, conduit, etc.) by connecting a leakage current tester such as Simpson Model 229-2 or equivalent between the earth ground and all e
5、xposed metal parts of the appliance (input/output terminals, screwheads, metal overlays, control shaft, etc.). Plug the AC line cord of the appliance directly into a 120V AC 60 Hz outlet and turn the AC power switch on. Any current measured must not exceed 0.5 mA.ANY MEASUREMENTS NOT WITHIN THE LIMI
6、TS OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER.2. PRODUCT SAFETY NOTICE Many electrical and mechanical parts in the appliance have special safety related characteristics. These are often not evident from visual inspec
7、tion nor the protection afforded by them necessarily can be obtained by using replacement components rated for voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this Service Manual. Electrical components having such features are identified by
8、marking with a on the schematics and on the parts list in this Service Manual.The use of a substitute replacement component which does not have the same safety characteristics as the PIONEER recommended replacement one, shown in the parts list in this Service Manual, may create shock, fire, or other
9、 hazards. Product Safety is continuously under review and new instructions are issued from time to time. For the latest information, always consult the current PIONEER Service Manual. A subscription to, or additional copies of, PIONEER Service Manual may be obtained at a nominal charge from PIONEER.
10、 LeakagecurrenttesterReading shouldnot be above0.5 mADeviceundertestTest allexposed metalsurfacesAlso test withplug reversed(Using AC adapterplug as required)EarthgroundAC Leakage Test(FOR USA MODEL ONLY)WARNINGThis product contains lead in solder and certain electrical parts contain chemicals which
11、 are known to the state of California to cause cancer, birth defects or other reproductive harm.Health & Safety Code Section 25249.6 - Proposition 65NOTICE(FOR CANADIAN MODEL ONLY)Fuse symbols (fast operating fuse) and/or (slow operating fuse) on PCB indicate that replacement parts must be of identi
12、cal designation.REMARQUE(POUR MODLE CANADIEN SEULEMENT)Les symboles de fusible (fusible de type rapide) et/ou (fusible de type lent) sur CCI indiquent que les pices de remplacement doivent avoir la mme dsignation.This service manual is intended for qualified service technicians ; it is not meant for
13、 the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual.Improperly performed repairs can adversely affect the safety and reliability of the product and m
14、ay void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician.RadioFans.CN 收音机爱 好者资料库 VSX-1016V-K356785678CDFABEImportant Check Points for Good ServicingIn this manu
15、al, procedures that must be performed during repairs are marked with the below symbol.Please be sure to confirm and follow these procedures.1. Product safetyPlease conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by following the sa
16、fety instructions described in this manual.1 Use specified parts for repair.Use genuine parts. Be sure to use important parts for safety.2 Do not perform modifications without proper instructions.Please follow the specified safety methods when modification(addition/change of parts) is required due t
17、o interferences such as radio/TV interference and foreign noise.3 Make sure the soldering of repaired locations is properly performed.When you solder while repairing, please be sure that there are no cold solder and other debris.Soldering should be finished with the proper quantity. (Refer to the ex
18、ample)4 Make sure the screws are tightly fastened.Please be sure that all screws are fastened, and that there are no loose screws.5 Make sure each connectors are correctly inserted.Please be sure that all connectors are inserted, and that there are no imperfect insertion.6 Make sure the wiring cable
19、s are set to their original state.Please replace the wiring and cables to the original state after repairs.In addition, be sure that there are no pinched wires, etc.7 Make sure screws and soldering scraps do not remain inside the product.Please check that neither solder debris nor screws remain insi
20、de the product.8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.Damaged power cords may lead to fire accidents, so please be sure that there are no damages.If you find a damaged power cord, please exchange it with a suitable one.9 There should be no s
21、park traces or similar marks on the power plug.When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure connections and suitable usage. Please exchange the power cord if necessary.0 Safe environment should be secured during servicing.Whe
22、n you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries. Please pay attention to your surroundings and repair safely. 2. AdjustmentsTo keep the original performance of the products, optimum adjustments and confirmation of ch
23、aracteristics within specification.Adjustments should be performed in accordance with the procedures/instructions described in this manual.4. CleaningFor parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper cleaning should be p
24、erformed to restore their performances.3. Lubricants, Glues, and Replacement partsUse grease and adhesives that are equal to the specified substance. Make sure the proper amount is applied.5. Shipping mode and Shipping screwsTo protect products from damages or failures during transit, the shipping m
25、ode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. VSX-1016V-K412341234CDFABE CONTENTS 1. SPECIFICATIONS .62. EXPLODED VIEWS AND PARTS LIST.102.1 PACKING SECTION .102.2 EXTERIOR SECTION.122.
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Pioneer-VSX1016TXVK-avr-sm 维修电路原理图 Pioneer VSX1016TXVK avr sm 维修 电路 原理图