Sony-STRDE595-int-sm 维修电路原理图.pdf

《Sony-STRDE595-int-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Sony-STRDE595-int-sm 维修电路原理图.pdf（54页珍藏版）》请在收音机爱好者资料库上搜索。

1、1SERVICE MANUALUS ModelCanadian ModelSTR-DE595AEP ModelUK ModelE ModelAustralian ModelKorean ModelSTR-DE495/DE595STR-DE495/DE595FM STEREO/FM-AM RECEIVERAUDIO POWER SPECIFICATIONSPOWER OUTPUT AND TOTALHARMONIC DISTORTION:With 8 ohm loads, both channels driven, from40 20,000 Hz; rated 90 watts per cha

2、nnelminimum RMS power, with no more than0.09 % total harmonic distortion from 250milliwatts to rated output (STR-DE595 areacode US only).Amplifier sectionPOWER OUTPUTModels of area code US, CNDRated Power Output at Stereo Mode(8 ohms 40 Hz 20 kHz, THD 0.09 %)STR-DE595:90 W + 90 WSTR-DE495:70 W + 70

3、WReference Power Output(8 ohms 40 Hz 20 kHz, THD 0.09 %)STR-DE595:FRONT 1) : 90 W/chCENTER 1) : 90 WSURR 1) : 90 W/chSTR-DE495:FRONT 1) : 70 W/chCENTER 1) : 70 WSURR 1) : 70 W/ch(8 ohms 1 kHz, THD 0.7 %)STR-DE595:FRONT 1) : 100 W/chCENTER 1) : 100 WSURR 1) : 100 W/chSTR-DE495:FRONT 1) : 80 W/chCENTE

4、R 1) : 80 WSURR 1) : 80 W/chSPECIFICATIONSModels of area code AEP, UKRated Power Output at Stereo Mode(8 ohms 1 kHz, THD 0.7 %)STR-DE595:100 W + 100 W 2)STR-DE495:80 W + 80 W 2)Reference Power Output 2)(8 ohms 1 kHz, THD 0.7 %)STR-DE595:FRONT 1) : 100 W/chCENTER 1) : 100 WSURR 1) : 100 W/chSTR-DE495

5、:FRONT 1) : 80 W/chCENTER 1) : 80 WSURR 1) : 80 W/chModels of area code SPRated Power Output at Stereo Mode(8 ohms 1 kHz, THD 0.7 %)STR-DE595:90 W + 90 W 2)STR-DE495:70 W + 70 W 2)Reference Power Output 2)(8 ohms 1 kHz, THD 10 %)STR-DE595:FRONT 1) : 110 W/chCENTER 1) : 110 WSURR 1) : 110 W/chSTR-DE4

6、95:FRONT 1) : 90 W/chCENTER 1) : 90 WSURR 1) : 90 W/chVer 1.1 2003. 049-877-028-022003D0400-1 2003. 04Sony CorporationHome Audio CompanyPublished by Sony Engineering CorporationPhoto: STR-DE595Manufactured under license from Dolby Laboratories.“Dolby”, “Pro Logic” and the double-D symbol aretrademar

7、ks of Dolby Laboratories.“DTS” and “DTS Digital Surround” are registeredtrademarks of Digital Theater Systems, Inc. Continued on next page Models of area code KRRated Power Output at Stereo Mode(8 ohms 1 kHz, THD 0.7 %)STR-DE595:100 W + 100 W 2)90 W + 90 W 3)STR-DE495:80 W + 80 W 2)70 W + 70 W 3)Ref

8、erence Power Output 2)(8 ohms 1 kHz, THD 10 %)STR-DE595:FRONT 1) : 120 W/chCENTER 1) : 120 WSURR 1) : 120 W/chSTR-DE495:FRONT 1) : 100 W/chCENTER 1) : 100 WSURR 1) : 100 W/chModels of other area codeRated Power Output at Stereo Mode(8 ohms 1 kHz, THD 0.7 %)STR-DE595:100 W + 100 W 2)STR-DE495:80 W +

9、80 W 2)Reference Power Output 2)(8 ohms 1 kHz, THD 10 %)STR-DE595:FRONT 1) : 120 W/chCENTER 1) : 120 WSURR 1) : 120 W/chSTR-DE495:FRONT 1) : 100 W/chCENTER 1) : 100 WSURR 1) : 100 W/chRadioFans.CN 收音机爱 好者资料库2STR-DE495/DE5951) Depending on the sound field settings and thesource, there may be no sound

10、 output.2) Measured under the following conditions:Area codePower requirementsE2, AUS240 V AC, 50 HzSP, MY, AEP, UK, AR,230 V AC, 50 HzKRTW110 V AC, 60 HzFrequency responseMULTI CH IN10 Hz 50 kHz(STR-DE595 only), CD+0.5/2 dB (with sound(STR-DE495 only),field and tone bypassed)MD/TAPE, DVD,VIDEO 1, 2

11、CD/SACD (STR-DE59510 Hz 70 kHzonly)+0.5/2 dB (with soundfield and tone bypassed)Inputs (Analog)MULTI CH INSensitivity: 500 mV(STR-DE595 only), CD/Impedance: 50 kilohmsSACD (STR-DE595S/N 3) : 96 dBonly), CD (STR-DE495(A, 500 mV 4) )only), MD/TAPE, DVD,VIDEO 1, 23) INPUT SHORT (with sound field and to

12、nebypassed).4) Weighted network, input level.Inputs (Digital)DVD (Coaxial)Sensitivity: Impedance: 75 ohmsS/N: 100 dB(A, 20 kHz LPF)CD/SACD (Optical)Sensitivity: (STR-DE595 only),Impedance: VIDEO 2 (Optical)S/N: 100 dB(A, 20 kHz LPF)OutputsMD/TAPE (OUT),Voltage: 500 mVVIDEO1Impedance: 10 kilohms(AUDI

13、O OUT)SUB WOOFERVoltage: 2 VImpedance: 1 kilohmsToneGain levels:6 dB, 1 dB stepFM tuner sectionTuning range87.5 - 108.0 MHzAntenna terminals75 ohms, unbalancedIntermediate Frequency10.7 MHzSensitivityMono:18.3 dBf, 2.2 V/75 ohmsStereo:38.3 dBf, 22.5 V/75 ohmsUsable sensitivity11.2 dBf, 1 V/75 ohmsS/

14、NMono:76 dBStereo:70 dBHarmonic distortion at 1 kHzMono:0.3%Stereo:0.5%Separation45 dB at 1 kHzFrequency response30 Hz 15 kHz,+0.5/2 dBSelectivity60 dB at 400 kHzAM tuner sectionTuning rangeModels of area code US, CNDWith 10-kHz tuning scale: 530 1710 kHz 5)With 9-kHz tuning scale:531 1710 kHz 5)Mod

15、els of area code E2With 10-kHz tuning scale: 530 1610 kHz 5)With 9-kHz tuning scale:531 1602 kHz 5)Models of area code AUS, SP, AEP, UK, TW, KRWith 9-kHz tuning scale:531 1602 kHzModels of area code MX, ARWith 10-kHz tuning scale: 530 1610 kHzAntennaLoop antennaIntermediate Frequency450 kHzUsable se

16、nsitivity50 dB/m (at 1,000 kHz or999 kHz)S/N54 dB (at 50 mV/m)Harmonic distortion0.5 % (50 mV/m, 400 Hz)SelectivityAt 9 kHz:35 dBAt 10 kHz:40 dB5) You can change the AM tuning scale to 9 kHz or10 kHz. After tuning in any AM station, turn offthe receiver. Hold down PRESET TUNING + andpress ?/1 . All

17、preset stations will be erased whenyou change the tuning scale. To reset the scale to10 kHz (or 9 kHz), repeat the procedure.Video sectionInputsVideo:1 Vp-p, 75 ohmsComponent Video (STR-DE595 only, except formodels of area code AEP, UK):Y:1 Vp-p, 75 ohmsPB/B-Y:0.7 Vp-p, 75 ohmsPR/R-Y:0.7 Vp-p, 75 oh

18、msOutputsVideo:1 Vp-p, 75 ohmsComponent Video (STR-DE595 only, except formodels of area code AEP, UK):Y:1 Vp-p, 75 ohmsPB/B-Y:0.7 Vp-p, 75 ohmsPR/R-Y:0.7 Vp-p, 75 ohmsGeneralPower requirementsArea codePower requirementsUS, CND, MX120 V AC, 60 HzAEP, UK230 V AC, 50/60 HzSP, MY, KR, AR220 230 V AC, 50

19、/60 HzE2120/220/240 V AC, 50/60 HzTW110 V AC, 50/60 HzAUS240 V AC, 50HzPower consumptionArea codePower consumptionUS, MXSTR-DE595: 210 WCNDSTR-DE595: 310 VAAEP, UK, TW, KRSTR-DE595: 210 WSTR-DE495: 180 WSP, MYSTR-DE595: 180 WAUS, E2, ARSTR-DE595: 210 WPower consumption (during standby mode)0.3 WDime

20、nsions430 145 298 mm(16 7/8 5 6/8 11 6/8 in.)including projecting partsand controlsMass (Approx.)STR-DE595: 7.5 kg (16 lb 9 oz)STR-DE495: 7.2 kg (15 lb 14 oz)Supplied accessoriesFM wire antenna (1)AM loop antenna (1)Remote commander RM-U306A (1)R6 (size-AA) batteries (2)Design and specifications are

21、 subject to changewithout notice. AbbreviationCND: Canadian modelAUS: Australian modelMX: Mexican modelSP: Singapore modelE2: AC 120 V area in E modelAR: Argentine modelKR: Korean modelTW: Taiwan modelVer 1.1RadioFans.CN 收音机爱 好者资料库3STR-DE495/DE595MODEL IDENTIFICATION BACK PANEL Part No.MODELPART No.

22、DE595: Korean4-244-149-0sDE595: Taiwan4-244-149-1sDE595: Argentine4-244-149-4sDE595: US4-246-023-0sDE595: Canadian4-246-023-1sDE595: Australian4-246-023-2sDE595: Singapore, Malaysia4-246-023-3sDE595: E24-246-023-4sDE595: Mexican4-246-023-5sDE595: AEP4-246-023-6sDE595: UK4-246-023-7sDE495: AEP4-246-0

23、34-1sDE595: UK4-246-034-2sDE495: Singapore, Malaysia4-246-034-3sDE495: Taiwan4-246-034-4sDE495: Korean4-246-034-5sDE495: Australian4-246-034-7s1.5 k0.15 FACvoltmeter(0.75 V)To Exposed MetalParts on SetEarth GroundSAFETY CHECK-OUTAfter correcting the original service problem, perform the follow-ing s

24、afety check before releasing the set to the customer:Check the antenna terminals, metal trim, “metallized” knobs, screws,and all other exposed metal parts for AC leakage.Check leakage as described below.LEAKAGE TESTThe AC leakage from any exposed metal part to earth ground andfrom all exposed metal

25、parts to any exposed metal part having areturn to chassis, must not exceed 0.5 mA (500 microampers.).Leakage current can be measured by any one of three methods.1.A commercial leakage tester, such as the Simpson 229 or RCAWT-540A. Follow the manufacturers instructions to use theseinstruments.2.A bat

26、tery-operated AC milliammeter. The Data Precision 245digital multimeter is suitable for this job.3.Measuring the voltage drop across a resistor by means of aVOM or battery-operated AC voltmeter. The “limit” indica-tion is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson

27、250 and Sanwa SH-63Trd are ex-amples of a passive VOM that is suitable. Nearly all batteryoperated digital multimeters that have a 2 V AC range are suit-able. (See Fig. A)SAFETY-RELATED COMPONENT WARNING!COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INTHE PA

28、RTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTS WHOSEPART NUMBERS APPEAR AS SHOWN IN THIS MANUAL ORIN SUPPLEMENTS PUBLISHED BY SONY.ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT!LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 SUR LESDIAGRAMMES SCHMATIQUES ET LA LISTE DES

29、PICES SONTCRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NEREMPLACER CES COMPOSANTS QUE PAR DES PICES SONYDONT LES NUMROS SONT DONNS DANS CE MANUEL OUDANS LES SUPPLMENTS PUBLIS PAR SONY.Ver 1.14TABLE OF CONTENTS1. GENERALMain unit . 5Remote button description. 62. DISASSEMBLY2-1. Case . 72-2. Front Pan

30、el Section . 82-3. Back Panel. 82-4. Digital Board. 92-5. Standby Board . 92-6. Main Board .103. TEST MODE. 114. DIAGRAMS4-1. IC Pin Descriptions .124-2. Circuit Boards Location . 154-3. Block Diagram Tuner/Audio Section . 164-4. Block Diagram Digital Section .174-5. Block Diagram Video/Display Sect

31、ion .184-6. Block Diagram Power Section . 194-7. Printed Wiring Boards Main Section . 214-8. Schematic Diagram Main Section (1/2) . 224-9. Schematic Diagram Main Section (2/2) . 234-10. Printed Wiring Board Digital Section (1/2) . 244-11. Printed Wiring Board Digital Section (2/2) . 254-12. Schemati

32、c Diagram Digital Section (1/2) .264-13. Schematic Diagram Digital Section (2/2) .274-14. Printed Wiring Board Video Section .284-15. Schematic Diagram Video Section . 294-16. Printed Wiring Boards Display Section . 304-17. Schematic Diagram Display Section .314-18. Printed Wiring Boards Power Secti

33、on . 324-19. Schematic Diagram Power Section . 334-20. IC Block Diagrams. 345. EXPLODED VIEWS5-1. Case Section . 365-2. Front Panel Section .375-3. Chassis Section-1 . 385-4. Chassis Section-2 . 396. ELECTRICAL PARTS LIST. 40STR-DE495/DE5955STR-DE495/DE595SECTION 1GENERALThis section is extractedfro

34、m instruction manual.6STR-DE495/DE5957STR-DE495/DE595Note : This set can be disassemble according to the following sequence.SECTION 2DISASSEMBLY2-1. CASE2-1.CASE(Page 7)2-2.FRONT PANEL SECTION(Page 8)2-3.BACK PANEL(Page 8)SET2-5.STANDBY BOARD(Page 9)2-4.DIGITAL BOARD(Page 9)2-6.MAIN BOARD(Page 10)No

35、te : Follow the disassembly procedure in the numerical order given.1 two screws(case 3 TP2)2 three screws(case 3 TP2)3 two screws(case 3 TP2)4 case8STR-DE495/DE5952-2. FRONT PANEL SECTION2-3. BACK PANEL5 front panel section3 two screws(BVTP3 x 8)1 CNS42 CNP7914 five screws(BVTP3 x 8)1 CNS72 CNS84 CN

36、P9015 CN9086 CN9063 CNP1567 three screws(BVTP3 x 8)9 three screws(BVTP3 x 8)9 six screws(BVTP3 x 8)8 five screws(BVTP3 x 8)qa screw (BVTP3 x 8)0 screw (BVTP3 x 8)qs back panel9STR-DE495/DE5952-4. DIGITAL BOARD1 CNS45 CNS16 CNS22 CNP63 CNP58 screw (BVTP3 x 8)9 bracket (digital)7 DIGITAL board4 screw

37、(BVTP3 x 8)5 STANDBY board1 CNP9052 CNP9023 CNP9034 three screws (BVTP3 x 6)2-5. STANDBY BOARDVer 1.110STR-DE495/DE5957 MAIN board1 CNP8012 CNP8025 screw(BVTP3 x 6)3 two screws(BVTP3 x 6)4 two screws(BVTP3 x 6)6 two screws(BVTP3 x 6)2-6. MAIN BOARDVer 1.111STR-DE495/DE595SECTION 3TEST MODEFACTORY PR

38、ESET MODE* All preset contents are reset to the default setting.* Procedure:While depressing the FM MODE and the PRESET TUNING -buttons simultaneously, press the ?/1 button to turn on themain power.The message “FACTORY” appears for a moment and the presentcontents are reset to the default values.AM

39、CHANNEL STEP 9 kHz/10 kHz SELECTIONMODE (US, Canadian, E model only)* Either the 9 kHz step or 10 kHz step can be selected for the AMchannel step.* Procedure:Press the TUNER FM/AM button to set AM and press the ?/1button to turn off the main power.While depressing the TUNING + button or thePRESET TU

40、NING + button, press the ?/1 button to turn on themain power.Either the message “9k STEP” or “10k STEP” appears for amoment and select the desired step.SPEAKER SIZE SELECTION MODE* Either the normal speaker or micro satellite speaker can be se-lected.* Procedure:While depressing the MAIN MENU button

41、, press the ?/1 but-ton to turn on the main power.Either the message “NORM. SP.” or “MICRO SP.” appears for amoment and select the desired speaker size.FLUORESCENT INDICATOR TUBE TEST MODE* All fluorescent segments are tested.When this test is activated, all segments light on at the sametime, then e

42、ach segment lights on one after another.* Procedure:While depressing the FM MODE and the MD/TAPE buttonssimultaneously, press the ?/1 button to turn on the main power.1.ALL segments light on.2CH, SURROUND, MOVIE and MUSIC LED light on.2.Press the VIDEO 1 button, confirm display.2CH and MOVIE LED lig

43、ht on.3.Press the VIDEO 1 button, confirm display.SURROUND and MUSIC LED light on.SWLSLCRSSBSRL F EdBkHzmft.MHzDDDDSPSP ASP BOPTSLEEPCOAXMULTI CH IN12 D.RANGEEQSTEREOMONORDSDIGITALMEMORYEXPROLOGICII DTS-ESNEO:6 MPEG-2 AACLSLRSRdBHzft.SP ASP BCOAX1D.RANGEEQMONOMEMORYEXII-ESNEO:6-2SWCSSBL F EkmMHzDDDD

44、SPOPTSLEEPMULTI CH IN2STEREORDSDIGITALPROLOGIC DTSMPEGAAC4.Press the VIDEO 1 button, all segments and all LEDs light on.5.Every pressing the VIDEO 1 button turns on each segment andLED one after another in the same order.(Not only the VIDEO 1 button, but also the other buttons suchas VIDEO 2, DVD, M

45、D/TAPE, CD and TUNER FM/AM canbe used.)SOUND FIELD CLEAR MODE* The preset sound field is cleared when this mode is activated.Use this mode before returning the product to clients uponcompletion of repair.* Procedure:While depressing the 2CH button, press the ?/1 button to turnon the main power.The m

46、essage “SF. CLR.” appears for a moment and initializa-tion is performed.SOFTWARE VERSION DISPLAY MODE* The software version is displayed.* Procedure:While depressing the FM MODE and the DVD buttons simul-taneously, press the ?/1 button to turn on the main power.The model name, destination and the so

47、ftware version are dis-played for a moment.KEY CHECK MODE* Button check* Procedure:While depressing the MUSIC and the TUNING - buttons si-multaneously, press the ?/1 button to turn on the main power.Either the message “REST 26” (STR-DE495) or “REST 27”(STR-DE595) appears.Every pressing of any button

48、 other than the ?/1 counts downthe buttons. The buttons which are already counted once are notcounted again. When all buttons are pressed “REST 00” appears.When MASTER VOLUME control is rotated in clockwise direc-tion, “VOL MIN”, “VOL 1” to “VOL 73”, “VOL MAX” ap-pears for a moment.AUTOBETICAL MODE

49、(AEP, UK model only)* When this mode is used, the receiver scans the broadcasts thatcan be received by the tuner, and sets up the broadcasts.Be sure to start scanning after connecting the antenna.* Procedure:Check that the antenna is connected.While depressing the MEMORY button, press the ?/1 button

50、to turn on the main power.The message “AUTO-BETICAL SELECT” appears for a mo-ment and the receiver starts scanning.COMMAND MODE SELECTION MODE* The command mode (AV1 or AV2) of the remote commandercan be selected.* Procedure:While depressing the ENTER button, press the ?/1 button toturn on the main