Technics-SUC909U-pre-sm1(1) 维修电路原理图.pdf
《Technics-SUC909U-pre-sm1(1) 维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《Technics-SUC909U-pre-sm1(1) 维修电路原理图.pdf(61页珍藏版)》请在收音机爱好者资料库上搜索。
1、Table Of Contents COVER 1 Note 2 Location of Controls 3 To Supply Power Source 3.1 Power Supply to Main Circuit 3.2 Operation Check 4 Operation Checks and Component ReplacementProcedures 5 Type Illustration of ICs, Transistors and Diodes 6 Schematic Diagram 6.1 Schematic Diagram Notes 6.2 Schematic
2、Diagram 7 Printed Circuit Board Diagram 8 Block Diagram 9 Wiring Connection Diagram 10 Measurements and Adjustments 10.1 Measurement instruments and Special tools 10.2 Output Voltage Adjustment 11 Terminal Function of ICs 11.1 IC701 (M38503M2404F) : Micro Computer 12 Replacement Parts List 13 Cabine
3、t Parts Location 14 Packaging Service ManualTOP NEXT AD9907176C2Control AmplifierG SU-C909UColour(K).Black TypeArea(E).Europe and Russia.RadioFans.CN 收音机爱 好者资料库PVPV 1999 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.TOP NEXT
4、 RadioFans.CN 收音机爱 好者资料库Table Of ContentsCOVER 1 Note 2 Location of Controls 3 To Supply Power Source 3.1 Power Supply to Main Circuit 3.2 Operation Check 4 Operation Checks and Component ReplacementProcedures 5 Type Illustration of ICs, Transistors and Diodes 6 Schematic Diagram 6.1 Schematic Diagr
5、am Notes 6.2 Schematic Diagram 7 Printed Circuit Board Diagram 8 Block Diagram 9 Wiring Connection Diagram 10 Measurements and Adjustments 10.1 Measurement instruments and Special tools 10.2 Output Voltage Adjustment 11 Terminal Function of ICs 11.1 IC701 (M38503M2404F) : Micro Computer 12 Replaceme
6、nt Parts List 13 Cabinet Parts Location 14 Packaging PVPVService ManualTOP NEXT AD9907176C2Control AmplifierG SU-C909UColour(K).Black TypeArea(E).Europe and Russia. 1999 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.TOP NEXT
7、 1 NoteTOP PREVIOUS NEXT Refer to the servise manual for Model No. SE-A909S (ORDER No. AD9907177C2) for information on Accessories, Connections, Operations and Packaging. TOP PREVIOUS NEXT 2 Location of ControlsTOP PREVIOUS NEXT TOP PREVIOUS NEXT 3 To Supply Power SourceTOP PREVIOUS NEXT This unit S
8、U-C909U is designed to operate on power supplied from the Power Amplifier SE-A909S. When operating the unit SU-C909U alone for testing and servicing, without having power supplied from the Power Amplifier SE-A909S, use the following method. 3.1 Power Supply to Main Circuit 3.2 Operation Check TOP PR
9、EVIOUS NEXT 3.1 Power Supply to Main CircuitTOP PREVIOUS NEXT 1. Apply 10 V AC power to the section between the point TP1 and the point TP2 . Shown in Fig.1 2. Connect the DC+12 V to+15 V (more than 0.1 A) to the point TP5 , and the GND terminal to the point TP4 using the DC power supply. Shown in F
10、ig.1 3. Connect the DC -12 V to -15 V (more than 0.1 A) to the point TP3 , and the GND terminal to the point TP4 using the DC power supply. Shown in Fig.1 TOP PREVIOUS NEXT 3.2 Operation CheckTOP PREVIOUS NEXT 1. Input a signal (1 kHz, 100 mV) to the each line-in terminal.2. Connect the oscilloscope
11、 or the speaker with the built-in amplifier to the PRE OUT terminals and check if the signals are outputting from this unit.Fig.1 TOP PREVIOUS NEXT 4 Operation Checks and Component Replacement/ProceduresTOP PREVIOUS NEXT TOP PREVIOUS NEXT 5 Type Illustration of ICs, Transistors and DiodesTOP PREVIOU
12、S NEXT TOP PREVIOUS NEXT 6 Schematic DiagramTOP PREVIOUS NEXT 6.1 Schematic Diagram Notes 6.2 Schematic Diagram TOP PREVIOUS NEXT 6.1 Schematic Diagram NotesTOP PREVIOUS NEXT G This schematic diagram may be modified at any time with the development of new technology. Notes: H S801: VGCA switch ()H S
13、802: Tape monitor switch (TAPE MONITOR)H S804: Input select switch (SELECTOR)H S805: Unit on/off switch (/I)H VR301: Volume control VR (VOLUME)H VR311: Output voltage adjustment VR (L ch)H VR312: Output voltage adjustment VR (R ch)H VR401: Balance control VR (BALANCE)H VR402: Tone control VR (BASS)H
14、 VR403: Tone control VR (TREBLE)G Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (high-impedance) with the chassis taken as standard. Therefore, there may exist some errors in the voltage values, depending on theinternal impedance of the DC
15、 circuit tester.No mark : Power ONG Important safety notice:Components identified by mark have special characteristics important for safety.Furthermore, special parts which have purposes of fire-retardant (resistors), high-quality sound (capacitors), low-noise (resistors), etc. are used.When replaci
16、ng any of components, be sure to use only manufacturers specified parts shown in the parts list.G Caution! IC and LSI are sensitive to static electricity.Secondary trouble can be prevented by taking care during repair.Cover the parts boxes made of plastics with aluminum foil.Ground the soldering iro
17、n.Put a conductive mat on the work table.Do not touch the legs of IC or LSI with the fingers directly.G Voltage and signal lineG : Positive voltage lineG : Negative voltage lineG : Phono signal lineG : Tape rec signal lineTOP PREVIOUS NEXT 6.2 Schematic DiagramTOP PREVIOUS NEXT TOP PREVIOUS NEXT 7 P
18、rinted Circuit Board DiagramTOP PREVIOUS NEXT TOP PREVIOUS NEXT 8 Block DiagramTOP PREVIOUS NEXT TOP PREVIOUS NEXT 9 Wiring Connection DiagramTOP PREVIOUS NEXT TOP PREVIOUS NEXT 10 Measurements and AdjustmentsTOP PREVIOUS NEXT 10.1 Measurement instruments and Special tools 10.2 Output Voltage Adjust
19、ment TOP PREVIOUS NEXT 10.1 Measurement instruments and Special toolsTOP PREVIOUS NEXT G AC electric voltmeter (AC EVM)G AF oscillatorTOP PREVIOUS NEXT 10.2 Output Voltage AdjustmentTOP PREVIOUS NEXT 1. Turn on the power.2. Select the input source to CD.3. Connect the measuring instrument as shown i
20、n Fig.2 4. Apply 1 kHz, 200 mV signal to CD terminal.5. Adjust the VOLUME to maximum.6. Adjust VR311 (L ch) and VR312 (R ch) so that the output voltage to AC 1.00 V0.2 dB. Shown in Fig.3 Fig.2 G Adjustment Point Fig.3 TOP PREVIOUS NEXT 11 Terminal Function of ICsTOP PREVIOUS NEXT 11.1 IC701 (M38503M
21、2404F) : Micro Computer TOP PREVIOUS NEXT 11.1 IC701 (M38503M2404F) : Micro ComputerTOP PREVIOUS NEXT Pin No.NameI/OFunction1VCCIPower supply (+5 V) terminal2VREFIReference voltage input3AGND-GND terminal4CSIChip select signal input5NC-Not used, open6REMCONIRemote control signal input7BACKUPIPower f
22、ailure detect signal input8NC-Not used, open9SELDATAOData signal output for input select IC (IC201 and IC202)10SELCLKOClock signal output for input select IC (IC201 and IC202)11SELSTBOStrobe signal output for input select IC (IC201 and IC202)12POWERSWISelector switch (S804) detect signal input13LEDC
23、LKOClock signal output for LED drive IC14LEDDATAOData signal output for LED drive IC15CNVSS-Connected to GND16VRDOWNOMotor drive signal output (Volume down)17VRUPOMotor drive signal output (Volume up)18RESETISystem reset signal input19XINIConnected to the ceramic oscillator (8 MHz)20XOUTOConnected t
24、o the ceramic oscillator (8 MHz)21GND-GND terminal22BATELED-Battery level (empty) LED (D809) drive signal output (Not used, open)23BATFLED-Battery level (full) LED (D809) drive signal output (Not used, open)24VIALEDOVIA LED drive signal output25VGALEDOVGCA LED drive signal output26STABYLEDOStand by
25、LED drive signal output27FRNTOUTOFront output control signal output28CSWSOUT-Center/S.woofer/Surround output control signal output (Not used, open)29PWRRLYOPower control signal output30CHRGRLY-Battery charge relay control signal output (Not used, open)31BATRLY-Battery drive relay control signal outp
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Technics-SUC909U-pre-sm11 维修电路原理图 Technics SUC909U pre sm1 维修 电路 原理图