HHScott-208-pwr-sm 维修电路原理图.pdf
《HHScott-208-pwr-sm 维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《HHScott-208-pwr-sm 维修电路原理图.pdf(4页珍藏版)》请在收音机爱好者资料库上搜索。
1、H.H.SCOTT-IIIPowdermillRoad, Maynard,Mass.INSTRUCTIONS FOR THE MODEL 20s SO-wattSTEREOPHONICLABORATORY POWER AMPLIFIERThe 208 is a precision, dual power amplifier designed for high quality audio appli-cations.It is ideally suited for use with the 355 AM-FM multiplexstereo control centeror a good qua
2、lity preamplifier.The 208 is completely stable under all conditionsand maybe used with any electrostatic loudspeakers. .INSTALLATIONThe 208 can be placed on a shelf.in a cabinet, or in a bookcase.When used withthe 355 it may be as close or as far as desired.If you wish, the 208 may actually beclampe
3、d to the 355 to make an integrated unit.The two clamps for this purpose are avail-able at no charge by writing to the Parts Dept., H. H. Scott, III Powdermill Rd., Maynard,Mass.Wherever the 208 is placed, adequateprovision for ventilationshould be made . Neverenclose the amplifier completely.If it i
4、s placed inside a cabinet, either the back or thefront should have openings to allow dissipationof the warm air.CONNECTIONSTo the Model 355 - If you plan to use the 208 bolted to the 355, or next to it, theshort leads supplied with the 208 are ideal.Connect one cable from the 355 left output tothe l
5、eft 1.5v input on the 208.Connect the other cable from the 355 right Output to theriht channel l.5v input on the 208.If you intend to separate the 208 fram the 355, useloner audio cables but follow the same connectioninstructions.To a Preamplifier - Shielded audio cables are provided with most pream
6、plifiers.Ifyou are using preamplifiers with over 2.0 volts output connect shielded cable from thepreamplifiersLeft or Channel A output to the Left 2.5 volt input.on the 208.Connectanother cable from the Right or ChannelB output of the preamplifier to the right 2.5 voltinput on the 208.If you use a p
7、reamplifierwith 1.0 to 2.0 volt output, follow the samedirectionsexcept use the 1.5 voltinputs on the 208.Power Connections - The power cord60 cycle, AC source.Do not use with DC.liary AC outlets on the back of the 355 orner, leave the on-off switch of the 208 inpreamplifier)is turned on or off, it
8、willshoul be plugged into any 105 to 125 volt, 50 toThe amplifier can be connected to any of the auxi-of your preamplifier.When connected in this man-the on position at all times.When the 355 (orturn the 208 on or off at the same time.Auxiliary AC outlets - The 208 has an auxiliary AC outlet.You may
9、 connect any unitslike a turntable or tape recorder to this outlet.When the 208 is turned off, these unitswill go off as well.Speakers - Terminal strips for makingspeaker connections are located on the back The one markedChannel A Speaker is for connecting the left speaker (as you face them).Theone
10、markedChannel B Speaker is for the riht.Below each strip are the numbers 4, 8, 16 andO.This permits you to match the amplifier output to the impedance of the speaker.Eachspeaker is rated by its manufacturerat a certain impedance.This information is eithermarkedon the speaker or can be supplied by th
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- HHScott-208-pwr-sm 维修电路原理图 HHScott 208 pwr sm 维修 电路 原理图