JVC-RX7030VBK-avr-sm 维修电路原理图.pdf

《JVC-RX7030VBK-avr-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《JVC-RX7030VBK-avr-sm 维修电路原理图.pdf（95页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUALCOPYRIGHT 2003 VICTOR COMPANY OF JAPAN, LTD.No.220582003/5AUDIO /VIDEO CONTROL RECEIVER2205820035RX-7030VBKTABLE OF CONTENTS1 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2、. . 1-32 Disassembly method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1- 43 Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3、 . . . . . . . . . . . . . . . 1-124 Description of major ICs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14231564897/P0+10MENUENTERCONTROLA/V CONTROL RECEIVER10/0Area SuffixJ - U.S.A.C - CanadaRadioFans.CN 收音机爱 好

4、者资料库1-2 (No.22058)SPECIFICATION* Corresponding to Linear PCM, Dolby Digital, and DTS Digital Surround (with sampling frequency - 32 kHz, 44.1 kHz, 48 kHz).Designs & specifications are subject to change without noticeAmplifierOutput PowerAt Stereo operation Front ch110 W per channel, min. RMS, driven

5、 into 8, 20 Hz to 20 kHz, with no more than 0.08% total harmonic distortion.At Surround operationFront ch110 W per channel, min. RMS, driven into 8 at 1 kHz, with no more than 0.8% total harmonic distortion.Center ch110 W, min. RMS, driven into 8 at 1 kHz, with no more than 0.8% total harmonic disto

6、rtion.Surround ch110 W per channel, min. RMS, driven into 8 at 1 kHz, with no more than 0.8% total harmonic distortion.Surround Back ch110 W, min. RMS, driven into 8 at 1 kHz, with no more than 0.8% total harmonic distortion.AudioAudio Input Sensitivity/Impedance (1 kHz)DVD IN, VCR IN, TV SOUND/DBS

7、IN 200 mV/47 kCD IN, TAPE/CDR IN200 mV/47 kAudio Input(DIGITAL IN)*CoaxialDIGITAL 1 (DVD) : 0.5 V(p-p)/75 OpticalDIGITAL 2 (CD), DIGITAL 3 (TV), DIGITAL 4 (CDR) : -21 dBm to -15 dBm (660 nm 30 nm)Audio Output LevelSUBWOOFER OUT : 1VRecording Output LevelVCR OUT, TAPE/CDR OUT : 200 mVDigital outputOp

8、tical : DIGITAL OUTSignal wave length660 nmOutput level-21 dBm to -15 dBmSignal-to-Noise Ratio (66 IHF/78 IHF) DVD IN, VCR IN, TV SOUND/DBS IN 87 dB/80 dB CD IN TAPE/CDR IN87 dB/80 dBFrequency Response (8 at 1 kHz, with no more than 0.8% total harmonic distortion.) DVD IN, VCR IN, TV SOUND/DBS IN20

9、Hz to 100 kHz (+1 dB, -3 dB)CD IN, TAPE/CDR IN20 Hz to 100 kHz (+1 dB, -3 dB)Equalization (5 bands)63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz (8 dB)Bass boost+6 dB 1.0 dB at 100 HzVideoVideo Input Sensitivity/ImpedanceComposite videoDVD IN, VCR IN, TV SOUND/DBS IN1 V(p-p)/75S-videoDVD IN, VCR IN, TV SOUND/

10、DBS IN(Y: luminance)1 V(p-p)/75(C: chrominance, burst)0.286 V(p-p)/75Component videoDVD IN, DBS IN(Y: luminance)1 V(p-p)/75(PB/PR): 0.7 V(p-p)/75Video Output LevelComposite videoVCR OUT, MONITOR OUT 1 V(p-p)/75S-videoVCR OUT, MONITOR OUT(Y: luminance)1 V(p-p)/75(C: chrominance, burst) 0.286 V(p-p)/7

11、5Component videoMONITOR OUT(Y: luminance)1 V(p-p)/75(PB/PR)0.7 V(p-p)/75SynchronizationNegativeSignal-to-Noise Ratio45 dBFM tuner (IHF)Tuning Range87.5 MHz to 108.0 MHzUsable SensitivityMonaural12.8 dBf (1.2 V/75)50 dB Quieting SensitivityMonaural16.0 dBf (1.7 V/75)Stereo37.5 dBf (20.5 V/75)Stereo S

12、eparation at REC OUT35 dB at 1 kHzAM tuner Tuning Range530 kHz to 1 710 kHzGeneralPower RequirementsAC 120V 60 HzPower Consumption320 W/440 VA (at operation) 2 W (in standby mode)Dimensions (W x H x D)435 mm x 157 mm x 425 mm (17 3/16 in. x 6 3/16 in. x 16 3/4 in.)Mass12.1 kg (26.7 lbs)RadioFans.CN

13、收音机爱 好者资料库(No.22058)1-3SECTION 1Precautions1.1Safety Precautions(1) This design of this product contains special hardware andmany circuits and components specially for safety purpos-es. For continued protection, no changes should be madeto the original design unless authorized in writing by themanuf

14、acturer. Replacement parts must be identical tothose used in the original circuits. Services should be per-formed by qualified personnel only.(2) Alterations of the design or circuitry of the product shouldnot be made. Any design alterations of the product shouldnot be made. Any design alterations o

15、r additions will voidthe manufacturers warranty and will further relieve themanufacture of responsibility for personal injury or propertydamage resulting therefrom.(3) Many electrical and mechanical parts in the products havespecial safety-related characteristics. These characteris-tics are often no

16、t evident from visual inspection nor can theprotection afforded by them necessarily be obtained by us-ing replacement components rated for higher voltage, watt-age, etc. Replacement parts which have these specialsafety characteristics are identified in the Parts List of Ser-vice Manual. Electrical c

17、omponents having such featuresare identified by shading on the schematics and by ( ) onthe Parts List in the Service Manual. The use of a substitutereplacement which does not have the same safety charac-teristics as the recommended replacement parts shown inthe Parts List of Service Manual may creat

18、e shock, fire, orother hazards.(4) The leads in the products are routed and dressed with ties,clamps, tubings, barriers and the like to be separated fromlive parts, high temperature parts, moving parts and/orsharp edges for the prevention of electric shock and firehazard. When service is required, t

19、he original lead routingand dress should be observed, and it should be confirmedthat they have been returned to normal, after reassem-bling.(5) Leakage shock hazard testingAfter reassembling the product, always perform an isola-tion check on the exposed metal parts of the product (an-tenna terminals

20、, knobs, metal cabinet, screw heads,headphone jack, control shafts, etc.) to be sure the productis safe to operate without danger of electrical shock.Do notuse a line isolation transformer during this check. Plug the AC line cord directly into the AC outlet. Using aLeakage Current Tester, measure th

21、e leakage currentfrom each exposed metal parts of the cabinet, particular-ly any exposed metal part having a return path to thechassis, to a known good earth ground. Any leakage cur-rent must not exceed 0.5mA AC (r.m.s.). Alternate check methodPlug the AC line cord directly into the AC outlet. Use a

22、nAC voltmeter having, 1,000 per volt or more sensitivityin the following manner. Connect a 1,500 10W resistorparalleled by a 0.15F AC-type capacitor between an ex-posed metal part and a known good earth ground.Measure the AC voltage across the resistor with the ACvoltmeter. Move the resistor connect

23、ion to each exposed metalpart, particularly any exposed metal part having a returnpath to the chassis, and measure the AC voltage acrossthe resistor. Now, reverse the plug in the AC outlet andrepeat each measurement. Voltage measured any mustnot exceed 0.75 V AC (r.m.s.). This corresponds to 0.5mA A

24、C (r.m.s.). 1.2Warning(1) This equipment has been designed and manufactured tomeet international safety standards.(2) It is the legal responsibility of the repairer to ensure thatthese safety standards are maintained.(3) Repairs must be made in accordance with the relevantsafety standards.(4) It is

25、essential that safety critical components are replacedby approved parts.(5) If mains voltage selector is provided, check setting for localvoltage.1.3CautionBurrs formed during molding may be left over on some partsof the chassis. Therefore, pay attention to such burrs in the case of pre-forming repa

26、ir of this system.1.4Critical parts for safetyIn regard with component parts appearing on the silk-screenprinted side (parts side) of the PWB diagrams, the parts that areprinted over with black such as the resistor ( ), diode ( )and ICP ( ) or identified by the mark nearby are criticalfor safety. Wh

27、en replacing them, be sure to use the parts of thesame type and rating as specified by the manufacturer. (This regulation dose not Except the J and C version)Good earth groundPlace this probe on each exposedmetal part.AC VOLTMETER(Having 1000 ohms/volts,or more sensitivity)1500 10W0.15 F AC TYPE1-4

28、(No.22058)SECTION 2Disassembly method2.1Removing the top cover(See Fig.1)(1) From the right and left sides of the main body, remove thefour screws A attaching the top cover.(2) From the back side of the main body, remove the threescrews B attaching the top cover.(3) Remove the top cover in the direc

29、tion of the arrow 2 whileextending the lower sections of the top cover in the direc-tion of the arrow 1.Fig.12.2Removing the front panel assembly(See Figs.2 and 3) Prior to performing the following procedures, remove the topcover.(1) Disconnect the card wire from the connector CN400 on themicon boar

30、d. (See Fig.2.)(2) Disconnect the card wire from the connector CN402 on thepower supply board. (See Fig.2.)(3) Remove the tie band and wire protection board fixing thecard wire. (See Fig.2.)(4) Remove the three screws C attaching the front panel as-sembly. (See Fig.2.)(5) From the bottom side of the

31、 main body, remove the fourscrews D attaching the front panel assembly. (See Fig.3.)(6) Remove the front panel assembly in the direction of the ar-row. (See Fig.3.)Fig.2Fig.3Top coverA211BACCCFront panel assemblyCard wireCN402Tie bandWire protectionboardCN400Micon boardPower supplyboardCard wireDDFr

32、ont panel assembly(No.22058)1-52.3Removing the rear panel(See Fig.4) Prior to performing the following procedures, remove the topcover.(1) From the back side of the main body, remove the strain re-lief from the rear panel in the direction of the arrow.(2) Remove the twenty-nine screws E, two screws

33、F and threescrews G attaching the rear panel.Fig.42.4Removing the I/O board(See Fig.5) Prior to performing the following procedures, remove the topcover and rear panel.(1) Remove the two plastic rivets in the direction of the arrow1 from the top side of the main body, remove the stopperboards in the

34、 direction of the arrow 2.(2) Remove the tie bands bundling the wires.(3) Disconnect the wire from the connector CN722 on the cen-ter board.(4) Disconnect the wire from the connector CN714 on the frontboard(L).(5) Disconnect the wire from the connector CN717 on the sur-round back board.(6) Disconnec

35、t the wire from the connector CN719 on the frontboard(R).(7) Disconnect the wire from the connector CN723 on the mainboard.(8) Disconnect the connectors (CN205,CN381,CN501) on theI/O board in an upward direction.Fig.5Strain reliefEGEFGEEEGRear panel1 112 221 112 22CN381CN205CN501Plastic rivetPlastic

36、rivetStopperboardStopper boardTie bandCenter boardTie bandsFront board(L)Surround boardFront board(R)CN719CN717CN714CN722CN723MainboardI/O board1-6 (No.22058)2.5Removing the tuner, DSP board, audio board, video board and S-video board(See Fig.6) Prior to performing the following procedures, remove t

37、he topcover, rear panel and I/O board.(1) Disconnect the card wire from the connector CN314 on theaudio board from the top side of the main body, take out thetuner.(2) (2) Disconnect the DSP board from the connector CN601on the micon board.(3) Disconnect the audio board from the connectors(CN101,CN3

38、03) on the micon board.(4) Disconnect the video board from the connector CN201 onthe micon board.(5) Disconnect the S-video board from the connector CN241on the micon board.Fig.62.6Removing the micon board(See Fig.7) Prior to performing the following procedures, remove the topcover, rear panel, I/O

39、board, tuner, DSP board, audio board,video board and S-video board.(1) From the top side of the main body, disconnect the cardwire from the connector CN400 on the micon board.(2) Disconnect the relay board from the connectors CN81 onthe micon board.(3) Disconnect the parallel wire from the connector

40、s CN931and CN932 on the micon board.(4) Disconnect the parallel wire from the connector CN831 onthe main board.(5) Remove the three screws H attaching the micon board.(6) Remove the three screws J attaching the transistors(Q921,Q931,Q941) to the chassis base.(7) Loosen the screw K attaching the mico

41、n board.Fig.7CN314TunerAudio boardCard wireCN601DSP boardCN303CN101Video boardS-video boardCN201CN241Micon boardCN400Micon boardRelayboardCN81CardwireCN931CN932HHHJTransistors(Q921,Q931,Q941)ChassisbaseKCN831Main board(No.22058)1-72.7Removing the speaker board(See Fig.8) Prior to performing the foll

42、owing procedures, remove the topcover and rear panel.(1) From the top side of the main body, remove the tie bandbundling the wires.(2) Disconnect the wires from the connectors (CN813,CN814)on the main board.(3) Disconnect the parallel wire from the connectors(CN931,CN932) on the micon board.(4) Take

43、 out the speaker board in the direction of the arrow.Fig.82.8Removing the main board(See Fig.9) Prior to performing the following procedures, remove the topcover.(1) From the top side of the main body, remove the tie bandsbundling the wires.(2) Remove the tie band and wire protection board bundlingt

44、he card wire.(3) Disconnect the wire from the connector CN811 on the pow-er transformer board 1.(4) Disconnect the relay board from the connectors (CN71,CN81) on the power supply board and micon board.(5) Disconnect the parallel wires from the connectors(CN831,CN881) on the main board.(6) Disconnect

45、 the wires from the connectors(CN723,CN813,CN814) on the main board.(7) Disconnect the wire from the connector CN722 on the cen-ter board.(8) Disconnect the wire from the connector CN714 on the frontboard(L).(9) Disconnect the wire from the connector CN717 on the sur-round back board.(10) Disconnect

46、 the wire from the connector CN719 on the frontboard(R).(11) Remove the screw K, five screws L, screw M and twoscrews N attaching the main board.(12) Take out the main board.Fig.9Fig.11Tie bandCN813Main boardSpeaker boardCN814CN931CN932Micon boardTie bandWireprotectionboardMicon boardCard wireTie ba

47、ndsCN811Powertransformerboard 1CN71CN81Relay boardPowersupplyboardCN831CN881MainboardCN723CN814CN813Center boardCN722Front board(L)CN714SurroundboardCN717Front board(R)CN719KNNLLMTiebandHeat sinkQQ1-8 (No.22058)2.9Removing the heat sink(See Figs.10 and 11) Prior to performing the following procedure

48、s, remove the topcover and main board.(1) From the reverse side of the main board, remove the twoscrews P attaching the main board to the heat sink. (SeeFig.10.)(2) Disconnect the connectors (CN701-CN706) on the mainboard, remove the main board. (See Fig.10.)(3) Remove the twelve screws Q attaching

49、the heat sink. (SeeFig.11.)Fig.10Fig.112.10 emoving the center board, surround back board, front amp. boards (L/R) and rear amp. boards (L/R)(See Figs.10 and 12) Prior to performing the following procedures, remove the topcover and main board.(1) From the reverse side of the main board, remove the t

50、woscrews P attaching the main board to the heat sink. (SeeFig.10.)(2) Disconnect the connectors (CN701-CN706) on the mainboard, remove the main board. (See Fig.10.)(3) Remove the two screws Q attaching the center board. (SeeFig.12.)(4) Remove the two screws Q attaching the front board(L).(See Fig.12