Yamaha-RXZ11-avr-sm(1) 维修电路原理图.pdf
《Yamaha-RXZ11-avr-sm(1) 维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《Yamaha-RXZ11-avr-sm(1) 维修电路原理图.pdf(243页珍藏版)》请在收音机爱好者资料库上搜索。
1、SERVICE MANUAL101069IMPORTANT NOTICEThis manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are alreadyknown and understood by the users, an
2、d have therefore not been restated.WARNING:Failure to follow appropriate service and safety procedures when servicing this product may result in personalinjury, destruction of expensive components, and failure of the product to perform as specified. For these reasons,we advise all YAMAHA product own
3、ers that any service required should be performed by an authorizedYAMAHA Retailer or the appointed service representative.IMPORTANT:The presentation or sale of this manual to any individual or firm does not constitute authorization, certification orrecognition of any applicable technical capabilitie
4、s, or establish a principle-agent relationship of any form.The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, andservice departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore,
5、 inevitableand specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, pleasecontact the distributors Service Division.WARNING:Static discharges can destroy expensive components. Discharge any static electricity your body may haveaccumul
6、ated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).IMPORTANT:Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit. CONTENTSTO SERVICE PERSONNEL . 2FRONT PANELS. 45REAR PANELS . 610REMOTE C
7、ONTROL PANELS. 11SPECIFICATIONS / 参考仕様 . 1216INTERNAL VIEW . 17DISASSEMBLY PROCEDURES / 分解手順. 1828UPDATING FIRMWARE /書込. 2938SELF-DIAGNOSTIC FUNCTION /(自己診断機能). 4085AMP ADJUSTMENT / 部調整 . 86DISPLAY DATA . 9091IC DATA . 92107PIN CONNECTION DIAGRAMS. 108110BLOCK DIAGRAMS . 111119PRINTED CIRCUIT BOARDS
8、. 120158SCHEMATIC DIAGRAMS. 159179REPLACEMENT PARTS LIST . 181235REMOTE CONTROL. 236240ADVANCED SETUP /設定 . 241242AV RECEIVER/AV AMPLIFIERP.O.Box 1, Hamamatsu, Japan 2008 All rights reserved.This manual is copyrighted by YAMAHA and may not be copied orredistributed either in print or electronically
9、without permission. 08.02RX-Z11/DSP-Z11RX-Z11/DSP-Z11RadioFans.CN 收音机爱 好者资料库RX-Z11/DSP-Z112RX-Z11/DSP-Z11WALLOUTLETEQUIPMENTUNDER TESTAC LEAKAGETESTER OREQUIVALENTINSULATINGTABLEWARNING: CHEMICAL CONTENT NOTICE!This product contains chemicals known to the State of California to cause cancer, or birt
10、h defects or other reproductiveharm.DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANYREASON WHAT SO EVER!Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or exposeeyes to solder/flux vapor!If you come i
11、n contact with solder or components located inside the enclosure of this product, wash your hands beforehandling food.1. Critical Components InformationComponents having special characteristics are marked sand must be replaced with parts having specifications equalto those originally installed.2. Le
12、akage Current Measurement (For 120V Models Only)When service has been completed, it is imperative to verifythat all exposed conductive surfaces are properly insulatedfrom supply circuits.Meter impedance should be equivalent to 1500 ohms shuntedby 0.15F.Leakage current must not exceed 0.5mA.Be sure t
13、o test for leakage with the AC plug in both polarities.本機搭載基板付接合部無鉛付。無鉛種類、修理時下記無鉛使用推奨。Sn+Ag+Cu (錫+銀+銅)Sn+Cu (錫+銅)Sn+Zn+Bi (錫+亜鉛+)注意:無鉛融点温度通常鉛入比3040程度高、合使用。All of the P.C.B.s installed in this unit and solder joints aresoldered using the lead free solder.Among some types of lead free solder currently
14、 available,it is recommended to use one of the following types for therepair work. Sn + Ag + Cu (tin + silver + copper) Sn + Cu (tin + copper) Sn + Zn + Bi (tin + zinc + bismuth)Caution:As the melting point temperature of the lead free solder isabout 30C to 40C (50F to 70F) higher than that of the l
15、eadsolder, be sure to use a soldering iron suitable to each solder.About lead free solder / 無鉛 TO SERVICE PERSONNELFor U model“CAUTION”“F1: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 4A,125V FUSE.”“F2: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH S
16、AME TYPE 15A,125V FUSE.”For C modelCAUTIONF1:REPLACE WITH SAME TYPE 4A, 125V FUSE.F2:REPLACE WITH SAME TYPE 15A, 125V FUSE.ATTENTIONF1:UTILISER UN FUSIBLE DE RECHANGE DE MME TYPE DE 4A, 125V.F2:UTILISER UN FUSIBLE DE RECHANGE DE MME TYPE DE 15A, 125V.RadioFans.CN 收音机爱 好者资料库RX-Z11/DSP-Z113RX-Z11/DSP-
17、Z11CAUTIONDanger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type.WARNING: Lithium batteries注意正電池交換爆発起。同一型名同等品以外電池絶対交換。WARNING: Lithium batteries are dangerous becausethey can be exploded by improper handling. Observe thefollowing precautions when handlin
18、g or replacing lithiumbatteries. Leave lithium battery replacement to qualified servicepersonnel. Always replace with batteries of the same type. When installing on the PC board by soldering, solderusing the connection terminals provided on the batterycells. Never solder directly to the cells. Perfo
19、rm thesoldering as quickly as possible. Never reverse the battery polarities when installing. Do not short the batteries. Do not attempt to recharge these batteries. Do not disassemble the batteries. Never heat batteries or throw them into fire.ADVARSEL!Lithiumbatteri Eksplosionsfare ved fejlagtig h
20、ndtering.Udskiftning m kun ske med batteri af samme fabrikat ogtype. Levr det brugte batteri tilbage til leverandren.VARNINGExplosionsfara vid felaktigt batteribyte. Anvnd sammabatterityp eller an ekvivalent typ som rekommenderas avapparattillverkaren. Kassera anvnt batteri enligtfabrikantens instru
21、ktion.VAROITUSParisto voi rjht, jos se on virheellisesti asennettu.Vaihda paristo ainoastaan laitevalmistajan suosittelemaantyyppiin. Hvit kytetty peristo valmistajan ohjeidenmukaisesti.RX-Z11/DSP-Z114RX-Z11/DSP-Z11DSP-Z11 (R, T, K, B, G, E, L models) FRONT PANELSRX-Z11 (U, C models)U modelC modelRX
22、-Z11/DSP-Z115RX-Z11/DSP-Z11DSP-Z11 (J model)RX-Z11 (A model)RX-Z11/DSP-Z116RX-Z11/DSP-Z11 REAR PANELSRX-Z11 (U model)RX-Z11 (C model)RX-Z11/DSP-Z117RX-Z11/DSP-Z11RX-Z11 (R model)RX-Z11 (T model)RX-Z11/DSP-Z118RX-Z11/DSP-Z11RX-Z11 (K model)RX-Z11 (A model)RX-Z11/DSP-Z119RX-Z11/DSP-Z11DSP-Z11 (B model
23、)DSP-Z11 (G, E models)RX-Z11/DSP-Z1110RX-Z11/DSP-Z11DSP-Z11 (L model)DSP-Z11 (J model)RX-Z11/DSP-Z1111RX-Z11/DSP-Z11 REMOTE CONTROL PANELSRAV380RX-Z11 (U, C models)RAV382RX-Z11 (R, T, K, A models)DSP-Z11 (B, G, E, L models)RAV33RX-Z11 (U, C, R, T, K, A models)DSP-Z11 (B, G, E, L, J models)RAV381DSP-
24、Z11 (J model)RX-Z11/DSP-Z1112RX-Z11/DSP-Z11 Audio Section / 部Minimum RMS Output Power (Power Amp. Section) /定格出力 (部) (20 Hz to 20 kHz, 0.04 % THD)FRONT L/RU, C, R, T, K, A, B, G, E, L models (8 ohms). 140 W + 140 WJ model (6 ohms) . 140 W + 140 WCENTERU, C, R, T, K, A, B, G, E, L models (8 ohms). 14
25、0 WJ model (6 ohms) . 140 WSURROUND L/RU, C, R, T, K, A, B, G, E, L models (8 ohms). 140 W + 140 WJ model (6 ohms) . 140 W + 140 WSURROUND BACK L/RU, C, R, T, K, A, B, G, E, L models (8 ohms). 140 W + 140 WJ model (6 ohms) . 140 W + 140 WFRONT PRESENCE L/RU, C, R, T, K, A, B, G, E, L models (8 ohms)
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Yamaha-RXZ11-avr-sm1 维修电路原理图 Yamaha RXZ11 avr sm 维修 电路 原理图