Yamaha-RXZ7-avr-sm(1) 维修电路原理图.pdf
《Yamaha-RXZ7-avr-sm(1) 维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《Yamaha-RXZ7-avr-sm(1) 维修电路原理图.pdf(235页珍藏版)》请在收音机爱好者资料库上搜索。
1、RX-Z7/DSP-Z71 0 111 6SERVICE MANUALIMPORTANT NOTICEThis manual has been provided for the use of authorized YAMAHA Retailers and their service personnelIt has been assumed that basic service procedures inherent to the industry, and more specifi cally YAMAHA Products, are already known and understood
2、by the users, and have therefore not been restatedWARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components, and failure of the product to perform as specifi ed For these reasons, we advise all
3、YAMAHA product owners that any service required should be performed by an authorized YAMAHA Retailer or the appointed service representativeIMPORTANT: The presentation or sale of this manual to any individual or fi rm does not constitute authorization, certifi cation or recognition of any applicable
4、 technical capabilities, or establish a principle-agent relationship of any formThe data provided is believed to be accurate and applicable to the unit(s) indicated on the cover The research, engineering, and service departments of YAMAHA are continually striving to improve YAMAHA products Modificat
5、ions are, therefore, inevitable and specifi cations are subject to change without notice or obligation to retrofi t Should any discrepancy appear to exist, please contact the distributors Service DivisionWARNING: Static discharges can destroy expensive components Discharge any static electricity you
6、r body may have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss)IMPORTANT: Turn the unit OFF during disassembly and part replacement Recheck all work before you apply power to the unit CONTENTSTO SERVICE PERSONNEL .23FRONT PANELS .45REAR
7、 PANELS .610REMOTE CONTROL PANELS .11SPECIFICATIONS / 参考仕様 .1217INTERNAL VIEW .18DISASSEMBLY PROCEDURES / 分解手順 .1927UPDATING FIRMWARE / 書込 .2831SELF-DIAGNOSTIC FUNCTION / (自己診断機能) .3284AMP ADJUSTMENT / 部調整 .85DISPLAY DATA .8687IC DATA .88105PIN CONNECTION DIAGRAMS .106110BLOCK DIAGRAMS .111115PRINTE
8、D CIRCUIT BOARDS . 116147SCHEMATIC DIAGRAMS .149175REPLACEMENT PARTS LIST .177223REMOTE CONTROL .224227ADVANCED SETUP / 本機設定変更 .228234AV RECEIVER/AV AMPLIFIERanimate 08.11P.O.Box 1, Hamamatsu, JapanCopyright 2008 All rights reserved.This manual is copyrighted by YAMAHA and may not be copied orredist
9、ributed either in print or electronically without permission.RX-Z7/DSP-Z7RadioFans.CN 收音机爱 好者资料库2RX-Z7/DSP-Z7RX-Z7/DSP-Z7This product contains chemicals known to the State of California to cause cancer, or birth defects or other reproductive harm.DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC
10、 COMPONENTS IN YOUR MOUTH FOR ANY REASON WHATSOEVER!Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor!If you come in contact with solder or components located inside the enclosure of this product, wash yo
11、ur hands before handling food.1. Critical Components InformationComponents having special characteristics are marked and must be replaced with parts having specifications equal to those originally installed.2. Leakage Current Measurement (For 120V Models Only)When service has been completed, it is i
12、mperative to verify that all exposed conductive surfaces are properly insulated from supply circuits. Meter impedance should be equivalent to 1500 ohms shunted by 0.15 F.本機搭載基板付接合部無鉛付。無鉛種類、修理時下記無鉛使用推奨。 Sn+Ag+Cu(錫 + 銀 + 銅) Sn+Cu(錫 + 銅) Sn+Zn+Bi(錫 + 亜鉛 + )注意:無鉛融点温度通常鉛入比 30 40程度高、 合使用。All of the P.C.B.
13、s installed in this unit and solder joints are soldered using the lead free solder.Among some types of lead free solder currently available, it is recommended to use one of the following types for the repair work. Sn + Ag + Cu (tin + silver + copper) Sn + Cu (tin + copper) Sn + Zn + Bi (tin + zinc +
14、 bismuth)Caution:As the melting point temperature of the lead free solder is about 30C to 40C (50F to 70F) higher than that of the lead solder, be sure to use a soldering iron suitable to each solder. TO SERVICE PERSONNEL Leakage current must not exceed 0.5mA. Be sure to test for leakage with the AC
15、 plug in both polari-ties.WALLOUTLETEQUIPMENTUNDER TESTAC LEAKAGETESTER OREQUIVALENTINSULATINGTABLEWARNING: CHEMICAL CONTENT NOTICE!About lead free solder / 無鉛For U model“CAUTION”“F1: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 10A, 125V FUSE.”“F2: FOR CONTINUED PROTEC
16、TION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 4A, 125V FUSE.”For C modelCAUTIONF1: REPLACE WITH SAME TYPE 10A, 125V FUSE.F2: REPLACE WITH SAME TYPE 4A, 125V FUSE.ATTENTIONF1: UTILISER UN FUSIBLE DE RECHANGE DE MME TYPE DE 10A, 125V.F2: UTILISER UN FUSIBLE DE RECHANGE DE MME TYPE DE 4A, 125V
17、.RadioFans.CN 收音机爱 好者资料库3RX-Z7/DSP-Z7RX-Z7/DSP-Z7CAUTIONDanger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type.WARNING: Lithium batteries注意正電池交換爆発起。同一型名同等品以外電池絶対交換。WARNING: Lithium batteries are dangerous because they can be exploded by improper handling
18、. Observe the following precautions when handling or replacing lithium batteries. Leave lithium battery replacement to qualified service personnel. Always replace with batteries of the same type. When installing on the PC board by soldering, solder using the connection terminals provided on the batt
19、ery cells. Never solder directly to the cells. Perform the soldering as quickly as possible. Never reverse the battery polarities when installing. Do not short the batteries. Do not attempt to recharge these batteries. Do not disassemble the batteries. Never heat batteries or throw them into fire.AD
20、VARSEL!Lithiumbatteri Eksplosionsfare ved fejlagtig hndtering.Udskiftning m kun ske med batteri af samme fabrikat og type. Levr det brugte batteri tilbage til leverandren.VARNINGExplosionsfara vid felaktigt batteribyte. Anvnd samma batterityp eller an ekvivalent typ som rekommenderas av apparattillv
21、erkaren. Kassera anvnt batteri enligt fabrikan-tens instruktion.VAROITUSParisto voi rjht, jos se on virheellisesti asennettu.Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hvit kytetty peristo valmistajan ohjeiden mu-kaisesti.4RX-Z7/DSP-Z7RX-Z7/DSP-Z7RX-Z7 (U, C models) FRONT PA
22、NELSRX-Z7 (A model)U modelC model5RX-Z7/DSP-Z7RX-Z7/DSP-Z7DSP-Z7 (R, T, K, B, G, E, L models)DSP-Z7 (J model)6RX-Z7/DSP-Z7RX-Z7/DSP-Z7RX-Z7 (U model) REAR PANELSRX-Z7 (C model)7RX-Z7/DSP-Z7RX-Z7/DSP-Z7RX-Z7 (A model)DSP-Z7 (R model)8RX-Z7/DSP-Z7RX-Z7/DSP-Z7DSP-Z7 (T model)DSP-Z7 (K model)9RX-Z7/DSP-
23、Z7RX-Z7/DSP-Z7DSP-Z7 (B model)DSP-Z7 (G, E models)10RX-Z7/DSP-Z7RX-Z7/DSP-Z7DSP-Z7 (L model)DSP-Z7 (J model)11RX-Z7/DSP-Z7RX-Z7/DSP-Z7 REMOTE CONTROL PANELSRAV36RAV389U, C modelsRAV391R, T, K, A, B, G, E, L modelsRAV390J model12RX-Z7/DSP-Z7RX-Z7/DSP-Z7 Audio Section / 部Minimum RMS Output Power (Powe
24、r Amp. Section) / 定格出力 ( 部 ) (20 Hz to 20 kHz)FRONT L/RU, C, R, T, K, A, B, G, E, L models (0.04 % THD, 8 ohms) .140 W + 140 WJ model (0.06 % THD, 6 ohms) .140 W + 140 WCENTERU, C, R, T, K, A, B, G, E, L models (0.04 % THD, 8 ohms) .140 WJ model (0.06 % THD, 6 ohms) .140 WSURROUND L/RU, C, R, T, K,
25、A, B, G, E, L models (0.04 % THD, 8 ohms) .140 W + 140 WJ model (0.06 % THD, 6 ohms) .140 W + 140 WSURROUND BACK L/RU, C, R, T, K, A, B, G, E, L models (0.04 % THD, 8 ohms) .140 W + 140 WJ model (0.06 % THD, 6 ohms) .140 W + 140 WMaximum Power / 実用最大出力 (JEITA, 1 kHz, 10 % THD) FRONT L/RR, T, K, L mo
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Yamaha-RXZ7-avr-sm1 维修电路原理图 Yamaha RXZ7 avr sm 维修 电路 原理图