Yamaha-RXV659-avr-sm 维修电路原理图.pdf
《Yamaha-RXV659-avr-sm 维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《Yamaha-RXV659-avr-sm 维修电路原理图.pdf(121页珍藏版)》请在收音机爱好者资料库上搜索。
1、SERVICE MANUAL100999IMPORTANT NOTICEThis manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are alreadyknown and understood by the users, an
2、d have therefore not been restated.WARNING:Failure to follow appropriate service and safety procedures when servicing this product may result in personalinjury, destruction of expensive components, and failure of the product to perform as specified. For these reasons,we advise all YAMAHA product own
3、ers that any service required should be performed by an authorizedYAMAHA Retailer or the appointed service representative.IMPORTANT:The presentation or sale of this manual to any individual or firm does not constitute authorization, certification orrecognition of any applicable technical capabilitie
4、s, or establish a principle-agent relationship of any form.The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, andservice departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore,
5、 inevitableand specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, pleasecontact the distributors Service Division.WARNING:Static discharges can destroy expensive components. Discharge any static electricity your body may haveaccumul
6、ated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).IMPORTANT:Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.I CONTENTSTO SERVICE PERSONNEL . 23FRONT PANELS. 35REAR PANELS . 58REMOTE
7、CONTROL PANELS. 9SPECIFICATIONS / 参考仕様 . 1012INTERNAL VIEW . 13DISASSEMBLY PROCEDURES / 分解手順 . 1417SELF DIAGNOSIS FUNCTION (DIAG) /自己診断機能 () . 1842AMP ADJUSTMENT / 部調整 . 43DISPLAY DATA . 4445IC DATA . 4655PIN CONNECTION DIAGRAM . 5657BLOCK DIAGRAMS . 5961PRINTED CIRCUIT BOARDS. 6278SCHEMATIC DIAGRAM
8、S. 7989REPLACEMENT PARTS LIST . 91120REMOTE CONTROL. 121ADVANCED SETUP . 122P.O.Box 1, Hamamatsu, JapanAV RECEIVER/AV AMPLIFIER 2006 All rights reserved.This manual is copyrighted by YAMAHA and may not be copied orredistributed either in print or electronically without permission.RX-V659/HTR-5960DSP
9、-AX759/DSP-AX759SERX-V659/HTR-5960DSP-AX759/DSP-AX759SE 06.02RadioFans.CN 收音机爱 好者资料库2RX-V659/HTR-5960DSP-AX759/DSP-AX759SERX-V659/HTR-5960DSP-AX759/DSP-AX759SEWALLOUTLETEQUIPMENTUNDER TESTAC LEAKAGETESTER OREQUIVALENTINSULATINGTABLEWARNING: CHEMICAL CONTENT NOTICE!The solder used in the production o
10、f this product contains LEAD. In addition, other electrical/electronic and/orplastic (where applicable) components may also contain traces of chemicals found by the California Health andWelfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm.DO NO
11、T PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANYREASON WHATSOEVER!Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes orexpose eyes to solder/flux vapor!If you come in contact with solder or components located
12、 inside the enclosure of this product, wash your handsbefore handling food.1. Critical Components InformationComponents having special characteristics are marked sand must be replaced with parts having specifications equal tothose originally installed.2. Leakage Current Measurement (For 120V Models
13、Only)When service has been completed, it is imperative to verifythat all exposed conductive surfaces are properly insulatedfrom supply circuits.GMeter impedance should be equivalent to 1500 ohms shuntedby 0.15F.GLeakage current must not exceed 0.5mA.“CAUTION”“F651, 652: FOR CONTINUED PROTECTION AGAI
14、NST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE10A, 125V FUSE.”CAUTIONF651, 652: REPLACE WITH SAME TYPE 10A, 125V FUSE.ATTENTIONF651, 652: UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE DE 10A, 125V.本機搭載基板付使用下記通。The P.C.B.s installed in this unit are soldered using thefollowing solder.About Lead Free So
15、lder / 無鉛Side ASide BSMT REFLOW ProcessMI FLOW ProcessSolder DipGBe sure to test for leakage with the AC plug in bothpolarities.DSP P.C.B.OPERATION P.C.B.MAIN P.C.B.POWER P.C.B.SUBTRANS P.C.B.VIDEO P.C.B.SIDE A / A面lead free solder / 無鉛lead free solder / 無鉛SIDE B / B面lead free solder / 無鉛lead free s
16、older / 無鉛lead free solder / 無鉛lead free solder / 無鉛lead free solder / 無鉛lead free solder / 無鉛I TO SERVICE PERSONNELRadioFans.CN 收音机爱 好者资料库3RX-V659/HTR-5960DSP-AX759/DSP-AX759SERX-V659/HTR-5960DSP-AX759/DSP-AX759SE無鉛種類、修理時下記無鉛使用推奨。Sn+Ag+Cu (錫+銀+銅)Sn+Cu (錫+銅)Sn+Zn+Bi (錫+亜鉛+)注意:1. 無鉛融点温度通常鉛入比3040程度高、合
17、使用。2. 鉛入使得場合、交換部品端子部周辺部無鉛取除、無鉛鉛入十分溶状態付。Among some types of lead free solder currently available,it is recommended to use one of the following types for therepair work. Sn + Ag + Cu (tin + silver + copper) Sn + Cu (tin + copper) Sn + Zn + Bi (tin + zinc + bismuth)Caution:1. As the melting point tempe
18、rature of the lead free solder isabout 30C to 40C (50F to 70F) higher than that of the leadsolder, be sure to use a soldering iron suitable to each solder.2. If lead solder must be used, be sure to remove lead free solderfrom each terminal section of the parts to be replaced andfrom the area around
19、it completely before soldering, or makesure that the lead free solder and lead solder melt togetherfully.I FRONT PANELSRX-V659 (U, C models)RX-V659 (R, T, K, A, G, E, L models)4RX-V659/HTR-5960DSP-AX759/DSP-AX759SERX-V659/HTR-5960DSP-AX759/DSP-AX759SEHTR-5960 (A model)DSP-AX759 (J model)HTR-5960 (U,
20、 C models)5RX-V659/HTR-5960DSP-AX759/DSP-AX759SERX-V659/HTR-5960DSP-AX759/DSP-AX759SERX-V659 (U, C models)I REAR PANELSDSP-AX759SE (B model)RX-V659 (R model)6RX-V659/HTR-5960DSP-AX759/DSP-AX759SERX-V659/HTR-5960DSP-AX759/DSP-AX759SERX-V659 (K model)RX-V659 (A model)RX-V659 (T model)7RX-V659/HTR-5960
21、DSP-AX759/DSP-AX759SERX-V659/HTR-5960DSP-AX759/DSP-AX759SERX-V659 (G, E models)RX-V659 (L model)HTR-5960 (U, C models)8RX-V659/HTR-5960DSP-AX759/DSP-AX759SERX-V659/HTR-5960DSP-AX759/DSP-AX759SEHTR-5960 (A model)DSP-AX759 (J model)DSP-AX759SE (B model)9RX-V659/HTR-5960DSP-AX759/DSP-AX759SERX-V659/HTR
22、-5960DSP-AX759/DSP-AX759SERAV320I REMOTE CONTROL PANELSRAV321RX-V659 (U, C models)HTR-5960 (U, C models)RX-V659 (R, T, K, A, G, E, L models)HTR-5960 (A model)DSP-AX759 (J model)DSP-AX759SE (B model)10RX-V659/HTR-5960DSP-AX759/DSP-AX759SERX-V659/HTR-5960DSP-AX759/DSP-AX759SEI SPECIFICATIONS / 参考仕様I A
23、udio Section / 部Minimum RMS Output Power (Power Amp. Section) / 定格出力 (部)RX-V659/DSP-AX759SE(20 Hz to 20 kHz, 0.06 % THD, 8 ohms)FRONT L/R. 100 W + 100 WCENTER . 100 WSURROUND L/R . 100 W + 100 WSURROUND BACK L/R . 100 W + 100 WHTR-5960(1 kHz, 0.7 % THD, 8 ohms)FRONT L/R. 115 W + 115 WCENTER . 115 WS
24、URROUND L/R . 115 W + 115 WSURROUND BACK L/R . 115 W + 115 WDSP-AX759(20 Hz to 20 kHz, 0.09 % THD, 6 ohms)FRONT L/R. 100 W + 100 WCENTER . 100 WSURROUND L/R . 100 W + 100 WSURROUND BACK L/R . 100 W + 100 WMaximum Power / 実用最大出力 (EIAJ) (1 kHz, 10 % THD)RX-V659/HTR-5960 (R, T, K, L models)FRONT L/R (8
25、 ohms) . 140 WCENTER (8 ohms) . 140 WSURROUND L/R (8 ohms). 140 WSURROUND BACK L/R (8 ohms). 140 WDSP-AX759FRONT L/R (6 ohms) . 140 WCENTER (6 ohms) . 140 WSURROUND L/R (6 ohms). 140 WSURROUND BACK L/R (6 ohms). 140 WMaximum Power Per Channel / MAX(Sp impedance set: 8 ohms minimum/1 kHz, 0.7 % THD 4
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Yamaha-RXV659-avr-sm 维修电路原理图 Yamaha RXV659 avr sm 维修 电路 原理图