Yamaha-RXV2600-avr-sm(1) 维修电路原理图.pdf
《Yamaha-RXV2600-avr-sm(1) 维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《Yamaha-RXV2600-avr-sm(1) 维修电路原理图.pdf(155页珍藏版)》请在收音机爱好者资料库上搜索。
1、SERVICE MANUAL100980IMPORTANT NOTICEThis manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are alreadyknown and understood by the users, an
2、d have therefore not been restated.WARNING:Failure to follow appropriate service and safety procedures when servicing this product may result in personalinjury, destruction of expensive components, and failure of the product to perform as specified. For these reasons,we advise all YAMAHA product own
3、ers that any service required should be performed by an authorizedYAMAHA Retailer or the appointed service representative.IMPORTANT:The presentation or sale of this manual to any individual or firm does not constitute authorization, certification orrecognition of any applicable technical capabilitie
4、s, or establish a principle-agent relationship of any form.The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, andservice departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore,
5、 inevitableand specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, pleasecontact the distributors Service Division.WARNING:Static discharges can destroy expensive components. Discharge any static electricity your body may haveaccumul
6、ated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).IMPORTANT:Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit. CONTENTSTO SERVICE PERSONNEL . 2FRONT PANELS. 3REAR PANELS . 46REMOTE CON
7、TROL PANELS. 7SPECIFICATIONS / 参考仕様 . 810INTERNAL VIEW . 11DISASSEMBLY PROCEDURES / 分解手順. 1215UPDATING FIRMWARE /書込. 1623SELF DIAGNOSIS FUNCTION (DIAG) /自己診断機能(). 2459AMP ADJUSTMENT / 部調整 . 6061DISPLAY DATA . 6263IC DATA . 6471BLOCK DIAGRAM. 7375PIN CONNECTION DIAGRAM . 7677PRINTED CIRCUIT BOARD . 7
8、899SCHEMATIC DIAGRAM . 101113PARTS LIST. 115150REMOTE CONTROL. 151153ADVANCED SETUP /設定 . 154Parts List for Carbon Resistors . 155AV RECEIVER/AV AMPLIFIERRX-V2600/DSP-AX2600P.O.Box 1, Hamamatsu, JapanRX-V2600/DSP-AX2600 2005 All rights reserved.This manual is copyrighted by YAMAHA and may not be cop
9、ied orredistributed either in print or electronically without permission. 05.11RadioFans.CN 收音机爱 好者资料库RX-V2600/DSP-AX26002RX-V2600/DSP-AX2600WALLOUTLETEQUIPMENTUNDER TESTAC LEAKAGETESTER OREQUIVALENTINSULATINGTABLEWARNING: CHEMICAL CONTENT NOTICE!The solder used in the production of this product con
10、tains LEAD. In addition, other electrical/electronic and/or plastic (whereapplicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (andpossibly other entities) to cause cancer and/or birth defects or other reproductive harm.DO NOT PLACE SOLDER, EL
11、ECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REA-SON WHATSOEVER!Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or exposeeyes to solder/flux vapor!If you come in contact with solder or components located inside the encl
12、osure of this product, wash your hands beforehandling food. TO SERVICE PERSONNEL1. Critical Components InformationComponents having special characteristics are marked sand must be replaced with parts having specifications equalto those originally installed.2. Leakage Current Measurement (For 120V Mo
13、dels Only)When service has been completed, it is imperative to verifythat all exposed conductive surfaces are properly insulatedfrom supply circuits.Meter impedance should be equivalent to 1500 ohmsshunted by 0.15F.“CAUTION”“F2: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME T
14、YPE 10A,125V FUSE.”CAUTIONF2: REPLACE WITH SAME TYPE 10A, 125V FUSE.ATTENTIONF2: UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE DE 10A, 125V.Leakage current must not exceed 0.5mA.Be sure to test for leakage with the AC plug in both polarities.About lead free solder / 無鉛The P.C.B.s installed in this un
15、it are soldered using thefollowing solder.本機搭載基板付使用下記通。Side ASide BSMT REFLOW ProcessMI FLOW ProcessSolder Dip無鉛種類、修理時下記無鉛使用推奨。Sn+Ag+Cu (錫+銀+銅)Sn+Cu (錫+銅)Sn+Zn+Bi (錫+亜鉛+)注意: 無鉛融点温度通常鉛入比3040程度高、合使用。 鉛入使得場合、交換部品端子部周辺部無鉛取除、無鉛鉛入十分溶状態付。Among some types of lead free solder currently available,it is recomm
16、ended to use one of the following types for therepair work. Sn + Ag + Cu (tin + silver + copper) Sn + Cu (tin + copper) Sn + Zn + Bi (tin + zinc + bismuth)Caution:1. As the melting point temperature of the lead free solderis about 30C to 40C (50F to 70F) higher than that ofthe lead solder, be sure t
17、o use a soldering iron suitableto each solder.2. If lead solder must be used, be sure to remove lead freesolder from each terminal section of the parts to bereplaced and from the area around it completely beforesoldering, or make sure that the lead-free solder andlead solder melt together fully.DSP
18、P.C.B.FUNCTION P.C.B.OPERATION P.C.B.MAIN P.C.B.POWER PC.B.INPUT P.C.B.A-VIDEO P.C.B.D-VIDEO P.C.B.Side A / A 面Lead Free Solder / 無鉛Lead Free Solder / 無鉛Lead Free Solder / 無鉛Lead Free Solder / 無鉛Lead Free Solder / 無鉛Side B / B 面Lead Free Solder / 無鉛Lead Free Solder / 無鉛Lead Free Solder / 無鉛Lead Free
19、 Solder / 無鉛Lead Free Solder / 無鉛Lead Free Solder / 無鉛Lead Free Solder / 無鉛Lead Free Solder / 無鉛RadioFans.CN 收音机爱 好者资料库RX-V2600/DSP-AX26003RX-V2600/DSP-AX2600 FRONT PANELSRX-V2600 (U, C models)DSP-AX2600 (J model)RX-V2600 (R, T, K, A, B, G, L models)RX-V2600/DSP-AX26004RX-V2600/DSP-AX2600 REAR PANEL
20、SRX-V2600 (U, C models)RX-V2600 (R model)RX-V2600 (T model)RX-V2600/DSP-AX26005RX-V2600/DSP-AX2600RX-V2600 (K model)RX-V2600 (A model)RX-V2600 (B model)RX-V2600/DSP-AX26006RX-V2600/DSP-AX2600RX-V2600 (G model)RX-V2600 (L model)DSP-AX2600 (J model)RX-V2600/DSP-AX26007RX-V2600/DSP-AX2600 REMOTE CONTRO
21、L PANELSRX-V2600 (U, C models)RX-V2600 (R, T, K, A, B, G, L models)DSP-AX2600 (J model)RX-V2600 (U, C models)RX-V2600 (R, T, K, A, B, G, L models)DSP-AX2600 (J model)RX-V2600/DSP-AX26008RX-V2600/DSP-AX2600 SPECIFICATIONS / 参考仕様 Audio Section / 部Minimum RMS Output Power (Power Amp. Section) / 定格出力 (部
22、) (20 Hz to 20 kHz)FRONT L/RU, C, R, T, K, A, B, G, L models (0.04 % THD, 8 ohms).130 W + 130 WJ model (0.06 % THD, 6 ohms) .130 W + 130 WCENTERU, C, R, T, K, A, B, G, L models (0.04 % THD, 8 ohms) . 130 WJ model (0.06 % THD, 6 ohms) . 130 WSURROUND L/RU, C, R, T, K, A, B, G, L models (0.04 % THD, 8
23、 ohms). 130 W + 130 WJ model (0.06 % THD, 6 ohms) .130 W + 130 WSURROUND BACK L/RU, C, R, T, K, A, B, G, L models (0.04 % THD, 8 ohms).130 W + 130 WJ model (0.06 % THD, 6 ohms) .130 W + 130 WMaximum Power / 実用最大出力 (EIAJ, 1kHz, 10 % THD)FRONT L/RR, T, K, L models (8 ohms). 180 W + 180 WJ model (6 ohm
24、s) . 180 W + 180 WCENTERR, T, K, L models (8 ohms). 180 WJ model (6 ohms) . 180 WSURROUND L/RR, T, K, L models (8 ohms). 180 W + 180 WJ model (6 ohms) . 180 W + 180 WSURROUND BACK L/RR, T, K, L models (8 ohms). 180 W + 180 WJ model (6 ohms) . 180 W + 180 WDynamic Power Per Channel / (IHF)U, C, R, T,
25、 K, A, L models (8/6/4/2 ohms) . 165/205/260/340 WMax. Power Per Channel / Max. B, G models (1 kHz, 0.7 %THD, 4 ohms)FRONT L/R . 190 W + 190 WCENTER . 190 WSURROUND L/R . 190 W + 190 WSURROUND BACK L/R . 190 W + 190 WDynamic Headroom / U, C, R, T, K, A, L models (8 ohms) . 1.11 dBIEC Power / IEC B,
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Yamaha-RXV2600-avr-sm1 维修电路原理图 Yamaha RXV2600 avr sm 维修 电路 原理图