Yamaha-RXSL80-avr-sm(1) 维修电路原理图.pdf
《Yamaha-RXSL80-avr-sm(1) 维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《Yamaha-RXSL80-avr-sm(1) 维修电路原理图.pdf(82页珍藏版)》请在收音机爱好者资料库上搜索。
1、I CONTENTSTO SERVICE PERSONNEL . 2IMPEDANCE SELECTOR . 3FRONT PANELS. 4REAR PANELS . 56REMOTE CONTROL PANELS. 6SPECIFICATIONS / 参考仕様. 710INTERNAL VIEW . 10DISASSEMBLY PROCEDURES / 分解手順. 1113SELF DIAGNOSIS FUNCTION (DIAG) /自己診断機能(). 1433D-AMP MODULE TROUBLESHOOTING /-故障診断. 33AMP ADJUSTMENT / 部調整.34DI
2、SPLAY DATA . 35IC DATA . 3642BLOCK DIAGRAM. 4344PIN CONNECTION DIAGRAM . 45PRINTED CIRCUIT BOARD . 4657SCHEMATIC DIAGRAM . 5864PARTS LIST . 6579REMOTE CONTROL. 8081 04.09100920P.O.Box 1, Hamamatsu, JapanSERVICE MANUALAV RECEIVER/AV AMPLIFIERRX-SL80RX-SL80IMPORTANT NOTICEThis manual has been provided
3、 for the use of authorized YAMAHA Retailers and their service personnel.It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are alreadyknown and understood by the users, and have therefore not been restated.WARNING:Failure to follow appr
4、opriate service and safety procedures when servicing this product may result in personalinjury, destruction of expensive components, and failure of the product to perform as specified. For these reasons,we advise all YAMAHA product owners that any service required should be performed by an authorize
5、dYAMAHA Retailer or the appointed service representative.IMPORTANT:The presentation or sale of this manual to any individual or firm does not constitute authorization, certification orrecognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.The da
6、ta provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, andservice departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitableand specifications are subject to change without notic
7、e or obligation to retrofit. Should any discrepancy appear to exist, pleasecontact the distributors Service Division.WARNING:Static discharges can destroy expensive components. Discharge any static electricity your body may haveaccumulated by grounding yourself to the ground buss in the unit (heavy
8、gauge black wires connect to this buss).IMPORTANT:Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.RadioFans.CN 收音机爱 好者资料库2RX-SL80RX-SL80WALLOUTLETEQUIPMENTUNDER TESTAC LEAKAGETESTER OREQUIVALENTINSULATINGTABLEI TO SERVICE PERSONNEL1. Cri
9、tical Components InformationComponents having special characteristics are marked s andmust be replaced with parts having specifications equal to thoseoriginally installed.2. Leakage Current Measurement (For 120V Models Only)When service has been completed, it is imperative to verifythat all exposed
10、conductive surfaces are properly insulatedfrom supply circuits.GMeter impedance should be equivalent to 1500 ohm shuntedby 0.15F.GLeakage current must not exceed 0.5mA.GBe sure to test for leakage with the AC plug in both polarities.WARNING: CHEMICAL CONTENT NOTICE!The solder used in the production
11、of this product contains LEAD. In addition, other electrical/electronic and/or plastic (whereapplicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (andpossibly other entities) to cause cancer and/or birth defects or other reproductive harm.DO N
12、OT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REA-SON WHATSOEVER!Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or exposeeyes to solder/flux vapor!If you come in contact with solder or components loca
13、ted inside the enclosure of this product, wash your hands beforehandling food.“CAUTION”“F1: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 5A, 125VFUSE.”CAUTIONF1: REPLACE WITH SAME TYPE 5A, 125V FUSE.ATTENTIONF1: UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE DE 5A, 125V.R
14、adioFans.CN 收音机爱 好者资料库3RX-SL80RX-SL80本機搭載基板付使用下記通。The P.C.B.s installed in this unit are soldered using thefollowing solder.About Lead Free Solder / 無鉛無鉛種類、修理時下記無鉛使用推奨。Sn+Ag+Cu (錫+銀+銅)Sn+Cu (錫+銅)Sn+Zn+Bi (錫+亜鉛+)注意: 無鉛融点温度通常鉛入比3040程度高、合使用。 鉛入使得場合、交換部品端子部周辺部無鉛取除、無鉛鉛入十分溶状態付。Among some types of lead fre
15、e solder currently available,it is recommended to use one of the following types for therepair work. Sn + Ag + Cu (tin + silver + copper) Sn + Cu (tin + copper) Sn + Zn + Bi (tin + zinc + bismuth)Caution:1. As the melting point temperature of the lead free solderis about 30C to 40C (50F to 70F) high
16、er than that ofthe lead solder, be sure to use a soldering iron suitableto each solder.2. If lead solder must be used, be sure to remove lead freesolder from each terminal section of the parts to bereplaced and from the area around it completely beforesoldering, or make sure that the lead free solde
17、r andlead solder melt together fully.Side A / A面Side B / B面DIGITAL P.C.B.Lead Free Solder / 無鉛Lead Free Solder / 無鉛INPUT P.C.B.Lead Free Solder / 無鉛MAIN P.C.B.Lead Free Solder / 無鉛Lead Free Solder / 無鉛POWER P.C.B.Lead Free Solder / 無鉛I IMPEDANCE SELECTOR(B, G models only)IMPEDANCE SELECTORWARNING:Do
18、 not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise this unit may be damaged.Side ASide BSMT REFLOW ProcessMI FLOW ProcessSolder Dip4RX-SL80RX-SL80I FRONT PANELSRX-SL80 (U, C, R, T, K, A, L models)RX-SL80 (B, G models)RX-SL80 (J model)5RX-SL80RX-SL80RX-SL8
19、0 (T model)RX-SL80 (K model)RX-SL80 (A model)RX-SL80(B, G models)I REAR PANELSRX-SL80 (U, C models)RX-SL80 (R model)6RX-SL80RX-SL80I REMOTE CONTROL PANELSU, C, R, T, K, A, L, J modelsB, G modelsRX-SL80 (L model)RX-SL80 (J model)7RX-SL80RX-SL80I Audio Section / 部Minimum RMS Output Power (Power Amp. S
20、ection) /定格出力 (部) (1 kHz)FRONT L/RU, C models (0.9% THD, 6 ohms) .(FTC) 65W + 65WR, T, K, A, B, G, L, J models (0.9% THD, 6 ohms) . 70W + 70WCENTERU, C models (0.9% THD, 6 ohms) . (FTC) 65WR, T, K, A, B, G, L, J models (0.9% THD, 6 ohms) . 70WSURROUND L/RU, C models (0.9% THD, 6 ohms) .(FTC) 65W + 6
21、5WR, T, K, A, B, G, L, J models (0.9% THD, 6 ohms) . 70W + 70WMaximum Power / 実用最大出力 (EIAJ, 1kHz, 10% THD)FRONT L or RR, T, K, A, B, G, L, J models (6 ohms). 100WCENTERR, T, K, A, B, G, L, J models (6 ohms). 100WSURROUND L or RR, T, K, A, B, G, L, J models (6 ohms). 100WInput Sensitivity / Input Imp
22、edance (入力感度/入力) (U, C, R, T, K, A, L, J models)DVD/CD, etc.200 mV / 47 k-ohms (B, G models)VIDEO 2, EXT. IN, TV IN .200 mV / 47 k-ohmsMaximum Input Signal Level / 最大許容入力 (1 kHz, 0.5%THD) (U, C, R, T, K, A, L, J models)DVD/CD, etc. 2.0 V or more (B, G models)VIDEO 2, EXT. IN, TV IN . 2.0 V or moreOu
23、tput Level / Output Impedance (出力電圧/出力)VCR OUT (U, C, R, T, K, A, L, J models) . 200 mV / 820 ohmsEXT., TV (B, G models) .200 mV / 1.0 k-ohmsSUB WOOFER (FRONT SP: Small) .2.0 V / 1.2 k-ohmsHeadphone Jack Rated Output / Impedance (出力/出力)DVD/CD, etc. (1 kHz, 47 mV, 8 ohms) . 100 mV / 100 ohmsFrequency
24、 Response / 周波数特性DVD/CD, etc. to FRONT L/R (20 Hz to 50 kHz) .+0/-3.0 dBTotal Harmonic Distortion / 全高調波歪率 (1 kHz, 35W, 6ohms) (U, C, R, T, K, A, L, J models)DVD/CD, etc. (Effect Off) to FRONT L/R . 0.04 % or less (B, G models)EXT. IN (Effect Off) to FRONT L/R . 0.04 % or lessSignal to Noise Ratio /
25、 信号対雑音比 (IHF-A network) (U, C, R, T, K, A, L, J models)DVD/CD, etc. (Input shorted, 250 mV, Effect Off) to SPOUT . 100 dB or more (B, G models)EXT. IN (Input shorted, 250 mV, Effect Off) to SP OUT. 100 dB or moreResidual Noise / 残留 (IHF-A network)FRONT L/R . 150 V or lessChannel Separation / (Vol -1
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Yamaha-RXSL80-avr-sm1 维修电路原理图 Yamaha RXSL80 avr sm 维修 电路 原理图