Yamaha-DVR700-hts-sm 维修电路原理图.pdf

《Yamaha-DVR700-hts-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Yamaha-DVR700-hts-sm 维修电路原理图.pdf（122页珍藏版）》请在收音机爱好者资料库上搜索。

1、* The DVX-700 consists of the DVR-700, NS-PSW700 and NS-P700.When accepting a repair order from the user, it is recommended to receive DVR-700, NS-PSW700 and NS-P700 as a set for the repair work.* When DVD MODULE P.C.B. of the DVR-700 is replaced, the serial number and new device key (ID number) MUS

2、T be reported to YCJ (Yamaha Corporation Japan) by email.Email: ycav-For more information, refer to “SERVICE PRECAUTIONS”.DVR-700/NS-PSW700/NS-P7001 0 11 2 0SERVICE MANUALIMPORTANT NOTICEThis manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.It has been

3、assumed that basic service procedures inherent to the industry, and more specifi cally YAMAHA Products, are already known and understood by the users, and have therefore not been restated.WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in p

4、ersonal injury, destruction of expensive components, and failure of the product to perform as specifi ed. For these reasons, we advise all YAMAHA product owners that any service required should be performed by an authorized YAMAHA Retailer or the appointed service representative.IMPORTANT: The prese

5、ntation or sale of this manual to any individual or fi rm does not constitute authorization, certifi cation or recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.The data provided is believed to be accurate and applicable to the unit(s) indi

6、cated on the cover. The research, engineering, and service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable and specifi cations are subject to change without notice or obligation to retrofi t. Should any discrepancy appear to exist,

7、please contact the distributors Service Division.WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).IMPORTANT: Turn the unit O

8、FF during disassembly and part replacement. Recheck all work before you apply power to the unit. CONTENTSTO SERVICE PERSONNEL .23PREVENTION OF ELECTROSTATIC DISCHARGE .4REGION MANAGEMENT INFORMATION .5SYSTEM COMPOSITION .5FRONT PANELS .68REAR PANELS .910REMOTE CONTROL PANELS .11SPECIFICATIONS .1214I

9、NTERNAL VIEW .15SERVICE PRECAUTIONS .1617DVR-700 DISASSEMBLY PROCEDURES .1820NS-PSW700 DISASSEMBLY PROCEDURES .2123UPDATING FIRMWARE .2437SELF-DIAGNOSTIC FUNCTION .3863DISPLAY DATA .6465IC DATA .6683PIN CONNECTION DIAGRAMS .8486BLOCK DIAGRAMS .8789PRINTED CIRCUIT BOARDS .9098SCHEMATIC DIAGRAMS .9910

10、6REPLACEMENT PARTS LIST .107117REMOTE CONTROL .118119SYSTEM MENU .120animate 08.12P.O.Box 1, Hamamatsu, JapanCopyright 2008 All rights reserved.This manual is copyrighted by YAMAHA and may not be copied orredistributed either in print or electronically without permission.DVD CONTROLLER DVR-700SUBWOO

11、FER / SYSTEM CONTROL NS-PSW700SPEAKERS NS-P700DVD HOME THEATER SYSTEMDVX-700本资料由O K X I A 视听皮带资源库w w w . o k x i a . c n 提供RadioFans.CN 收音机爱 好者资料库2DVR-700/NS-PSW700/NS-P700DVR-700/NS-PSW700/NS-P700This product contains chemicals known to the State of California to cause cancer, or birth defects or o

12、ther reproductive harm.DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHATSOEVER!Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor!If you come in contact wit

13、h solder or components located inside the enclosure of this product, wash your hands before handling food.1. Critical Components InformationComponents having special characteristics are marked and must be replaced with parts having specifications equal to those originally installed.2. Leakage Curren

14、t Measurement (For 120V Models Only)When service has been completed, it is imperative to verify that all exposed conductive surfaces are properly insulated from supply circuits. Meter impedance should be equivalent to 1500 ohms shunted by 0.15 F.All of the P.C.B.s installed in this unit and solder j

15、oints are soldered using the lead free solder.Among some types of lead free solder currently available, it is recommended to use one of the following types for the repair work. Sn + Ag + Cu (tin + silver + copper) Sn + Cu (tin + copper) Sn + Zn + Bi (tin + zinc + bismuth)Caution:As the melting point

16、 temperature of the lead free solder is about 30C to 40C (50F to 70F) higher than that of the lead solder, be sure to use a soldering iron suitable to each solder. TO SERVICE PERSONNEL Leakage current must not exceed 0.5mA. Be sure to test for leakage with the AC plug in both polari-ties.WALLOUTLETE

17、QUIPMENTUNDER TESTAC LEAKAGETESTER OREQUIVALENTINSULATINGTABLEWARNING: CHEMICAL CONTENT NOTICE!About lead free solderWARNING: Laser SafetyThis product contains a laser beam component. This component may emit invisible, as well as visible radiation, which may cause eye damage. To protect your eyes an

18、d skin from laser radiation, the following precautions must be used during servicing of the unit.1) When testing and/or repairing any component within the product, keep your eyes and skin more than 30 cm/1 feet away from the laser pick-up unit at all times. Do not stare at the laser beam at any time

19、.2) Do not attempt to readjust, disassemble or repair the laser pick-up, unless noted elsewhere in this manual.3) CAUTION: Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.For U model“CAUTION”“F701: FOR CONTINUED P

20、ROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 5A, 125V FUSE.”For C modelCAUTIONF701: REPLACE WITH SAME TYPE 5A, 125V FUSE.ATTENTIONF701: UTILISER UN FUSIBLE DE RECHANGE DE MME TYPE DE 5A, 125V.RadioFans.CN 收音机爱 好者资料库3DVR-700/NS-PSW700/NS-P700DVR-700/NS-PSW700/NS-P700Laser Emitting cond

21、itions:1) When the Top Cover is removed, and the STANDBY/ON SW is turned to the “ON” position, the laser component will emit a beam for several seconds to detect if a disc is present. During this time (5-10 sec.) the laser may radiate through the lens of the laser pick-up unit. Do not attempt any se

22、rvicing during this period!If no disc is detected, the laser will stop emitting the beam. When a disc is loaded, you will not be exposed to any laser emissions.2) The laser power level can be adjusted with the VR on the pick-up PWB, however, this level has been set by the factory prior to shipping f

23、rom the factory. Do not adjust this laser level control unless instruction is provided elsewhere in this manual. Adjustment of this control can increase the laser emission level from the device.Type: Semiconductor laser ALGaInPWave length: 655 nm (DVD) / 790 nm (VCD/CD)Output Power: 5 mW (DVD) / 7 m

24、W (VCD/CD)Beam divergence: 20 degreesLaser Diode PropertiesThe primary side of the power supply carries live mains voltage when the player is connected to the mains even when the player is switched off !This primary area is not shielded so it is possible to accidentally touch copper tracks and/or co

25、mponents when servicing the player.Service personnel have to take precautions to prevent touching this area or components in this area.Note:The screws on the DVD mechanism may never be touched, removed or re-adjusted.Handle the DVD mechanism with care when the unit has to be exchanged!The DVD mechan

26、ism is very sensitive for dropping or giving shocks.Warning for power supplyU, C modelsA, G, F, L, V models4DVR-700/NS-PSW700/NS-P700DVR-700/NS-PSW700/NS-P700Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Se

27、nsitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component damage caused by electro static discharge (ESD).1. Immediately before

28、handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power t

29、o the unit under test.2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.4.

30、 Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static (ESD protect-ed)” can generate electrical charge sufficient to damage ES devices.5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.6

31、. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material).7. Immediately before remo

32、ving the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed.CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.8. Minimize bodily

33、 motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as brushing together of your fabric clothes or lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device).Grounding for electrostatic breakdown preventio

34、n1. Human body grounding.Use the antistatic wrist strap to discharge the static electricity from your body.2. Work table grounding.Put a conductive material (sheet) or steel sheet on the area where the optical pickup is placed and ground the sheet.Caution:The static electricity of your clothes will

35、not be grounded through the wrist strap. So take care not to let your clothes touch the optical pickup. PREVENTION OF ELECTROSTATIC DISCHARGE1M-ohmsConductive material(sheet) or steel sheetAnti-static wrist strap5DVR-700/NS-PSW700/NS-P700DVR-700/NS-PSW700/NS-P700 DVR-700 NS-P700 L / R NS-PSW700DVX-7

36、00This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corpor

37、ation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.Region Management Information: This DVD player is designed and manufactured to respond to the Region Management Information tha

38、t is recorded on a DVD disc. If the Region number described on the DVD disc does not correspond to the Region number of this DVD player, this DVD player cannot play this disc. REGION MANAGEMENT INFORMATION14222255436The DVX-700 consists of the DVR-700, NS-PSW700 and NS-P700. SYSTEM COMPOSITION6DVR-7

39、00/NS-PSW700/NS-P700DVR-700/NS-PSW700/NS-P700U, C, A, G, F, L, V models FRONT PANELSDVR-700 Front view Top view(A, G, F, L, V models)POWER indicators(U, C model)7DVR-700/NS-PSW700/NS-P700DVR-700/NS-PSW700/NS-P700U, C, A, G, F, L, V modelsNS-PSW700 Front view Side view Top view8DVR-700/NS-PSW700/NS-P

40、700DVR-700/NS-PSW700/NS-P700 Front view Side view Front view Side view Side view Top viewNS-P700 R Top viewNS-P700 L Side viewNS-P7009DVR-700/NS-PSW700/NS-P700DVR-700/NS-PSW700/NS-P700G modelL, V modelsA modelU, C modelsF model REAR PANELSU, C, A, G, F, L, V modelsDVR-70010DVR-700/NS-PSW700/NS-P700D

41、VR-700/NS-PSW700/NS-P700NS-P700 RNS-P700 LU, C, A, G, F, L, V modelsNS-PSW700U, C, A, G, F, L, V modelsNS-P700U, C modelsU, C modelsU, C modelsA modelG, F modelsL modelV model11DVR-700/NS-PSW700/NS-P700DVR-700/NS-PSW700/NS-P700 REMOTE CONTROL PANELSU, C modelsA, L, V modelsG, F models12DVR-700/NS-PS

42、W700/NS-P700DVR-700/NS-PSW700/NS-P700 SPECIFICATIONS Speaker SectionType .Bass reflex speaker systemMagnetic shielding typeDriver Woofer .16 cm (6-5/16) cone type x 1Frequency Response .35 Hz to 130 kHz (-10dB) Input/Output SectionInput Terminal Analog audio . INPUT4 (AUX L/R: pin jack)Digital audio

43、 .INPUT1, 2 (OPTICAL)INPUT3 (COAXIAL)Others .DOCK (YDS-10, YDS-11, YBA-10)FM antenna terminalXM tuner (U, C models)SIRIUS tuner (U, C models)Output Terminal Analog audio .SPEAKERS L/ROthers .SYSTEM CONNECTOR GeneralPower Supply U, C models . AC 120 V, 60 HzA model . AC 240 V, 50 HzG, F, L models . A

44、C 230 V, 50 HzV model . AC 110 V, 60 HzPower Consumption .50 WStandby Power Consumption (reference data) .Less than 1 WDimensions (W x H x D) Excluding legs .194 mm x 450 mm x 400 mm(7-5/8 x 17-11/16 x 15-3/4)Weight .13 kg (28 lbs. 10 oz.)Finish Black color .U, C, A, G, F, L, V models Speaker Sectio

45、nType .Magnetic shielding typeDriver Woofer .5.5 cm (2-3/16) cone type x 2Tweeter .2.5 cm (1) balanced dome type x 1Frequency Response .130 Hz to 20 kHz (-10dB)Input Power Nominal .40 WMaximum .100 W GeneralDimensions (W x H x D) Excluding stands .95 mm x 190 mm x 98 mm(3-3/4 x 7-1/2 x 3-7/8)Includi

46、ng standsUpright position .95 mm x 206 mm x 106 mm(3-3/4 x 8-1/8 x 4-3/16)Horizontal position .190 mm x 111 mm x 106 mm(7-1/2 x 4-3/8 x 4-3/16)Weight (Excluding stands) .1.2 kg (2 lbs. 10 oz.)Finish Black color .U, C, A, G, F, L, V modelsDVR-700NS-PSW700NS-P700 Input/Output SectionInput Terminal Oth

47、ers .USBOutput Terminal Video .VIDEO (composite)COMPONENT (Y, PB, PR)HDMIOthers .SYSTEM CONNECTOR GeneralDimensions (W x H x D) .360 mm x 68 mm x 224 mm(14-3/16 x 2-11/16 x 8-13/16)Weight .2.6 kg (5 lbs. 11 oz.)Finish Black color .U, C, A, G, F, L, V models Amplifier SectionMaximum Power (JEITA, 6 o

48、hms, 10 % THD) SP OUT (1 kHz) .70 WSUBWOOFER (100 Hz) .70 WMinimum RMS Output Power (6 ohms, 1 % THD) SP OUT (1 kHz) .55 WSUBWOOFER (100 Hz) .55 WInput Sensitivity/Input Impedance AUX . 350 mV/32 k-ohmsMaximum Input Signal Level (1 kHz, DSP=Thru) AUX .2.2 V or moreFrequency Response (Analog, Digital

49、 input) SP OUT . -2.0 1 dB (20 Hz)0 dB (1 kHz)-0.5 1 dB (20 kHz)Signal to Noise Ratio (IHF-A network) SP OUT Analog .82 dB or moreDigital .98 dB or moreTotal Harmonic Distortion (Analog, Digital 20 kHz-LPF, 1 kHz, 18.5 V/6 ohms) SP OUT .0.06 % or lessResidual Noise (Analog, Digital 20 kHz-LPF, 1 kHz

50、, 18.5 V/6 ohms) SP OUT .138 V13DVR-700/NS-PSW700/NS-P700DVR-700/NS-PSW700/NS-P700Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, “MLP Lossless” and the double-D symbol are trademarks of Dolby Laboratories.“DTS” and “DTS Digital Surround” are registered trademarks of DTS, I