Yamaha-HTR3063-hts-sm 维修电路原理图.pdf
《Yamaha-HTR3063-hts-sm 维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《Yamaha-HTR3063-hts-sm 维修电路原理图.pdf(105页珍藏版)》请在收音机爱好者资料库上搜索。
1、1 0 11 6 7SERVICE MANUALIMPORTANT NOTICEThis manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.It has been assumed that basic service procedures inherent to the industry, and more specifi cally YAMAHA Products, are already known and understood by the use
2、rs, and have therefore not been restated.WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components, and failure of the product to perform as specifi ed. For these reasons, we advise all YAMAHA p
3、roduct owners that any service required should be performed by an authorized YAMAHA Retailer or the appointed service representative.IMPORTANT: The presentation or sale of this manual to any individual or fi rm does not constitute authorization, certifi cation or recognition of any applicable techni
4、cal capabilities, or establish a principle-agent relationship of any form.The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications
5、 are, therefore, inevitable and specifi cations are subject to change without notice or obligation to retrofi t. Should any discrepancy appear to exist, please contact the distributors Service Division.WARNING: Static discharges can destroy expensive components. Discharge any static electricity your
6、 body may have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit. CONTENTSTO SERVICE PERSONNEL .2FRONT PANELS .34REA
7、R PANELS .510REMOTE CONTROL PANELS .11SPECIFICATIONS .1216INTERNAL VIEW .17DISASSEMBLY PROCEDURES .1820UPDATING FIRMWARE .2123SELF-DIAGNOSTIC FUNCTION .2448DISPLAY DATA .4950IC DATA .5162BLOCK DIAGRAM .63PRINTED CIRCUIT BOARDS .6477PIN CONNECTION DIAGRAMS .78SCHEMATIC DIAGRAMS .7987REPLACEMENT PARTS
8、 LIST .8997REMOTE CONTROL .98102ADVANCED SETUP . 103104AV RECEIVER10.03RX-V367/HTR-3063Copyright 2010 All rights reserved.This manual is copyrighted by YAMAHA and may not be copied orredistributed either in print or electronically without permission.When the following parts are replaced, the model n
9、ame and the destination MUST be written to the back-up IC (EEPROM: IC222 of the DIGITAL P.C.B.) to have proper operation. (See No. 22 SOFT SWITCH menu of the self-diagnostic function.) EEPROM (IC222) of DIGITAL P.C.B. DIGITAL P.C.B.P.O.Box 1, Hamamatsu, JapanRX-V367/HTR-3063This product contains che
10、micals known to the State of California to cause cancer, or birth defects or other reproductive harm.DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHATSOEVER!Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inha
11、le solder fumes or expose eyes to solder/flux vapor!If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food.1. Critical Components InformationComponents having special characteristics are marked and must be replaced with par
12、ts having specifications equal to those originally installed.2. Leakage Current Measurement (For 120V Models Only)When service has been completed, it is imperative to verify that all exposed conductive surfaces are properly insulated from supply circuits. Meter impedance should be equivalent to 1500
13、 ohms shunted by 0.15 F.All of the P.C.B.s installed in this unit and solder joints are soldered using the lead free solder.Among some types of lead free solder currently available, it is recommended to use one of the following types for the repair work. Sn + Ag + Cu (tin + silver + copper) Sn + Cu
14、(tin + copper) Sn + Zn + Bi (tin + zinc + bismuth)Caution:As the melting point temperature of the lead free solder is about 30C to 40C (50F to 70F) higher than that of the lead solder, be sure to use a soldering iron suitable to each solder. TO SERVICE PERSONNEL Leakage current must not exceed 0.5mA
15、. Be sure to test for leakage with the AC plug in both polarities.WARNING: CHEMICAL CONTENT NOTICE!About lead free solderFor U model“CAUTION”“F1501: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 6A, 125V FUSE.”For C modelCAUTIONF1501: REPLACE WITH SAME TYPE 6A, 125V FUSE
16、.ATTENTIONF1501: UTILISER UN FUSIBLE DE RECHANGE DE MME TYPE DE 6A, 125V.WALLOUTLETEQUIPMENTUNDER TESTAC LEAKAGETESTER OREQUIVALENTINSULATINGTABLE2RX-V367/HTR-3063RX-V367/HTR-3063 FRONT PANELS3RX-V367/HTR-3063RX-V367/HTR-3063Top viewFront viewRX-V367 (R, K, A, B, G, F, L models)RX-V367 (U, C, T mode
17、ls)RX-V367 / HTR-30634RX-V367/HTR-3063RX-V367/HTR-3063HTR-3063 (U, C, T models)HTR-3063 (R, K, A, G, F, L models) REAR PANELS5RX-V367/HTR-3063RX-V367/HTR-3063RX-V367 (U model)RX-V367 (C model)RX-V367 (R model)6RX-V367/HTR-3063RX-V367/HTR-3063RX-V367 (T model)RX-V367 (K model)RX-V367 (A model)7RX-V36
18、7/HTR-3063RX-V367/HTR-3063RX-V367 (B, G, F models)RX-V367 (L model)HTR-3063 (U model)8RX-V367/HTR-3063RX-V367/HTR-3063HTR-3063 (T model)HTR-3063 (C model)HTR-3063 (R model)9RX-V367/HTR-3063RX-V367/HTR-3063HTR-3063 (K model)HTR-3063 (A model)HTR-3063 (G, E, F models)10RX-V367/HTR-3063RX-V367/HTR-3063
19、HTR-3063 (L model) REMOTE CONTROL PANELSSheet (T model)11RX-V367/HTR-3063RX-V367/HTR-3063RAV331(U, C models)RAV332(R, T, K, A, L models)RAV333(B, G, E, F models) SPECIFICATIONS Audio SectionMinimum RMS Output Power (Power Amp. Section)(1 kHz, 0.9 % THD)U, C models (8 ohms)FRONT L/R .100 W/chCENTER .
20、100 WSURROUND L/R .100 W/chR, T, K, A, B, G, F, L models (6 ohms)FRONT L/R .100 W/chCENTER .100 WSURROUND L/R .100 W/chMaximum Power (JEITA) (1 kHz, 10 % THD, 6 ohms)R, T, K, L modelsFRONT L/R .135 W/chCENTER .135 WSURROUND L/R .135 W/chMax. Power Per Channel (1 kHz, 0.7 % THD, 4 ohms)B, G, F, L mod
21、elsFRONT L/R .120 W/chCENTER .120 WSURROUND L/R .120 W/chIEC Power (1 kHz, 0.9 % THD, 8 ohms) B, G, F, L modelsFRONT L/R .95 W/chDynamic Power Per Channel (IHF) (FRONT L/R drive)U, C models(8/6/4/2 ohms) .110/130/160/180 WR, T, K, A, B, G, F, L models (6/4/2 ohms) .105/130/150 WDynamic Headroom U, C
22、 models(8 ohms) .0.23 dBInput Sensitivity/Input ImpedanceAV5, etc. . 200 mV / 47 k-ohmsMaximum Input Signal (1 kHz, 0.5 % THD, Effect on)AV5, etc. .2.3 V or moreOutput Level/Output ImpedanceAUDIO OUT (REC) . 200 mV / 1.2 k-ohmsSUBWOOFER (2 ch STEREO and FRONT SP: Small) . 1 V / 1.2 k-ohmsHeadphone J
23、ack Rated Output/ImpedanceAV5, etc. (1 kHz, 50 mV, 8 ohms) . 100 mV / 470 ohmsFrequency Response (10 Hz to 100 kHz)AV5, etc. to FRONT L/R .0 / -3.0 dBTotal Harmonic Distortion (1 kHz, 50 W)AV5, etc. (straight) to FRONT L/R SP OUTU, C models(8 ohms) .0.06 % or lessR, T, K, A, B, G, F, L models(6 ohms
24、) .0.06 % or lessSignal to Noise Ratio (IHF-A Network)AV5, etc. (STEREO) (Input shorted) to SP OUT250 mV . 98 dB or moreResidual Noise (IHF-A Network)FRONT L/R SP OUT .150 V or lessChannel SeparationAV5, etc. (Input 5.1 k-ohms shorted, 1 kHz / 10 kHz) . 60 dB or more / 45 dB or moreVolume Control .M
25、UTE / -80 dB to +16.5 dB / 0.5 dB stepTone Control CharacteristicsBASSBoost/Cut . 10 dB / 2 dB step / 50 HzTurnover frequency .350 HzTREBLEBoost/Cut .10 dB / 2 dB step / 20 kHzTurnover frequency .3.5 kHzFilter CharacteristicsFRONT, CENTER, SURROUND (H.P.F.) .fc=40/60/80/90/100/110/120/160/200 Hz, 12
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Yamaha-HTR3063-hts-sm 维修电路原理图 Yamaha HTR3063 hts sm 维修 电路 原理图