Yamaha-EMX5000-mix-sm 维修电路原理图.pdf
《Yamaha-EMX5000-mix-sm 维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《Yamaha-EMX5000-mix-sm 维修电路原理图.pdf(124页珍藏版)》请在收音机爱好者资料库上搜索。
1、EMX5000-12/201SERVICE MANUALPA011633 1.387K-9551 Printed in Japan 2002.3HAMAMATSU, JAPAN CONTENTSSPECIFICATIONS. 3/5PANEL LAYOUT. 7CIRCUIT BOARD LAYOUT. 11BLOCK & LEVEL DIAGRAM.12WIRING. 14DIMENSIONS. 14DISASSEMBLY PROCEDURE. 15LSI PIN DESCRIPTION. 20IC BLOCK DIAGRAM. 23CIRCUIT BOARDS. 24INSPECTIONS
2、. 39/46CIRCUIT DIAGRAMS. 54PARTS LISTThis document is printed on chlorine free (ECF) paper with soy ink.EMX5000-20本资料由O K X I A 视听皮带资源库w w w . o k x i a . c n 提供RadioFans.CN 收音机爱 好者资料库EMX5000-12/202WARNING: THIS APPARATUS MUST BE EARTHEDIMPORTANTTHE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANC
3、E WITH THE FOLLOWING CODE: GREEN-AND-YELLOW : EARTH BLUE : NEUTRAL BROWN : LIVEAs the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:The wire which is coloured GREEN and YELLOW must be
4、connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured GREEN and YELLOW.The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.The wire which is coloured BROWN must be connected to
5、 the terminal which is marked with the letter L or coloured RED.* This applies only to products distributed by YAMAHA KEMBLE MUSIC (U.K.) LTD.WARNINGComponents having special characteristics are marked and must bereplaced with parts having specification equal to those originally installed.IMPOR TANT
6、 NOTICEThis manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumedthat basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and under-stood by the users, and have therefore not been r
7、estated.WARNING :Failure to follow appropriate service and safety procedures when servicing this product may result in per-sonal injury, destruction of expensive components and failure of the product to perform as specified. Forthese reasons, we advise all Yamaha product owners that all service requ
8、ired should be performed by anauthorized Yamaha Retailer or the appointed service representative.IMPORTANT :This presentation or sale of this manual to any individual or firm does not constitute authorization certifi-cation, recognition of any applicable technical capabilities, or establish a princi
9、pal-agent relationship ofany form.The data provided is belived to be accurate and applicable to the unit(s) indicated on the cover. The research engineering, andservice departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitableand changes in s
10、pecification are subject to change without notice or obligation to retrofit. Should any discrepancy appear toexist, please contact the distributors Service Division.WARNING :Static discharges can destroy expensive components. Discharge any static electricity your body may haveaccumulated by groundin
11、g yourself to the ground bus in the unit (heavy gauge black wires connect tothis bus.)IMPORTANT :Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply powerto the unit.WARNING: CHEMICAL CONTENT NOTICE!The solder used in the production of this product contains
12、LEAD. In addition, other electrical/electronic and/or plastic (Whereapplicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possiblyother entities) to cause cancer and/or birth defects or other reproductive harm.DO NOT PLACE SOLDER, ELECTRIC
13、AL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHATSO EVER!Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or exposeeyes to solder/flux vapor!If you come in contact with solder or components located inside the enclosure
14、of this product, wash your hands before handlingfood.This mark urges servicemen to pay attention.RadioFans.CN 收音机爱 好者资料库EMX5000-12/203SPECIFICATIONSMaximum output powerSPEAKERS: 500 W+500 W/4 0.5% THD at 1 kHz325 W+325 W/8 0.5% THD at 1 kHzBRIDGE:1000 W/80.5% THD at 1 kHzFrequency response20 Hz20 kH
15、z +1 dB, 3 dB 1 W output into 8 (SPEAKERS OUT)20 Hz20 kHz +1 dB, 3 dB +4 dB output into 600 (ST OUT, ST SUB OUT, MONO OUT, AUX SEND, EFFECT SEND)Total harmonic distortionLess than 0.5% 20 Hz20 kHz, 250 W output into 4 (SPEAKERS OUT)Less than 0.3% 20 Hz20 kHz, +14 dB output into 600(ST OUT, ST SUB OU
16、T, MONO OUT, AUX SEND, EFFECT SEND)Hum & noise(Average, Rs=150)(with 20 Hz20 kHz BPF)128 dB equivalent input noise, 65 dB residual output noise (SPEAKERS OUT)95 dB residual output noise (ST OUT, ST SUB OUT, AUX SEND)84 dB (ST OUT, MONO OUT)ST master/MONO master fader at nominal level and all chan-ne
17、l On switches off and all channel fader at minimum.64 dB (68 dB S/N)(ST OUT, MONO OUT)ST master fader at nominal level and one channel On switch on and one channel fader at nominal level and one channel Gain control at nominal level.81 dB (AUX SEND)Master fader at nominal level and all channel On sw
18、itches off and all channel level control at minimum.80 dB (EFFECT SEND)All channel level control at minimum.Maximum voltage gain108 dBINPUT A/B to SPEAKERS OUT84 dBINPUT A/B to ST OUT, MONO OUT80 dBINPUT A/B to AUX SEND (PRE)90 dBINPUT A/B to AUX SEND (POST)78 dBINPUT A/B to EFFECT SEND58 dBST CH IN
19、 to ST OUTCrosstalk at 1 kHz68 dB adjacent input, 68 dB input to outputInput channel equalization15 dB MaximumHIGH10 kHzshelving*MID250 Hz5 kHzpeakingLOW100 Hzshelving* Turn over/roll off frequency of shelving: 3 dB below maximum variable level.ST Input channel equalization15 dB MaximumHIGH10 kHzshe
20、lving*MID2.5 kHzpeakingLOW100 Hzshelving* Turn over/roll off frequency of shelving: 3 dB below maximum variable level.CH peak indicatorsRed LED on each channel lits when POST EQ signal reaches the level 3 dB below clipping.CH signal indicatorsGreen LED on each channel lits when POST EQ signal reache
21、s the level 10 dB.Meters13 points LED meterPower amp select switch500W + 500W, 300W + 300W, 100W + 100WLimiterComp. : THD0.5% (SPEAKERS OUT)LIMIT indicatorsTurn on : THD0.5% (SPEAKERS OUT)Graphic equalizer9 bands (63, 125, 250, 500, 1k, 2k, 4k, 8k, 16k Hz), 12 dB MaximumInternal digital effect 116 p
22、rograms, parameter controlInternal digital effect 216 programs, parameter control, tap delay control, foot switch (DIGITAL EFFECT ON/OFF, TAP)Foot switch (FC5)Digital effect 2 mute: on/off, Tap delayProtection circuit (Power amp)POWER switch on/off mute, DC detection, TEMP (heatsink temp. 90C)Fan ci
23、rcuitstop low speed (50C) variable high speed (70C)Phantom power+48 V (balanced input)OptionFC5 (Foot switch), RK-124 (EMX5000-12)Power requirement/Power consumptionUSA and Canada:120 V AC 60 Hz, 400 WEurope:230 V AC 50 Hz, 550 WOther:240 V AC 50 Hz, 550 WGeneral specificationsDimensions (WxHxD)682
24、158 538 mm (EMX5000-20) / 478 158 538 mm (EMX5000-12)Weight19 kg (EMX5000-20) / 15 kg (EMX5000-12)AccessoriesPower cord, Owners ManualEMX5000-12/204For European ModelPurchaser/User Information specified in EN55103-1 and EN55103-2.Inrush Current: 70AConformed Environment: E1, E2, E3 and E4Input termi
25、nalsGain controlActual load impedanceFor use withnominal Input levelConnectors on mixerSensitivity11. Sensitivity is the lowest level that can produce an output of +4 dB (1.23 V) or the nominal output level when the unit is set at maximum gain. (All fader and level controls are at maximum position.)
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Yamaha-EMX5000-mix-sm 维修电路原理图 Yamaha EMX5000 mix sm 维修 电路 原理图