Yamaha-DSPN600-avr-sm 维修电路原理图.pdf
《Yamaha-DSPN600-avr-sm 维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《Yamaha-DSPN600-avr-sm 维修电路原理图.pdf(143页珍藏版)》请在收音机爱好者资料库上搜索。
1、SERVICE MANUAL101007IMPORTANT NOTICEThis manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are alreadyknown and understood by the users, an
2、d have therefore not been restated.WARNING:Failure to follow appropriate service and safety procedures when servicing this product may result in personalinjury, destruction of expensive components, and failure of the product to perform as specified. For these reasons,we advise all YAMAHA product own
3、ers that any service required should be performed by an authorizedYAMAHA Retailer or the appointed service representative.IMPORTANT:The presentation or sale of this manual to any individual or firm does not constitute authorization, certification orrecognition of any applicable technical capabilitie
4、s, or establish a principle-agent relationship of any form.The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, andservice departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore,
5、 inevitableand specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, pleasecontact the distributors Service Division.WARNING:Static discharges can destroy expensive components. Discharge any static electricity your body may haveaccumul
6、ated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).IMPORTANT:Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.I CONTENTSTO SERVICE PERSONNEL . 23FRONT PANELS. 34REAR PANELS . 58REMOTE
7、CONTROL PANELS. 9SPECIFICATIONS / 参考仕様. 1012INTERNAL VIEW . 13DISASSEMBLY PROCEDURES / 分解手順 . 1420UPDATING FIRMWARE /書込 . 2124SELF DIAGNOSIS FUNCTION (DIAG) /自己診断機能 () . 2550AMP ADJUSTMENT / 部調整 . 51DISPLAY DATA . 5255IC DATA . 5669PIN CONNECTION DIAGRAMS. 7071BLOCK DIAGRAMS . 7275PRINTED CIRCUIT BO
8、ARDS. 7695SCHEMATIC DIAGRAMS. 97108REPLACEMENT PARTS LIST . 109138REMOTE CONTROL. 139ADVANCED SETUP . 140141P.O.Box 1, Hamamatsu, JapanAV RECEIVER/AV AMPLIFIER 2006 All rights reserved.This manual is copyrighted by YAMAHA and may not be copied orredistributed either in print or electronically withou
9、t permission.RX-N600/RX-N600D/HTR-N5060/DSP-N600RX-N600/RX-N600D/HTR-N5060DSP-N600 06.06RadioFans.CN 收音机爱 好者资料库RX-N600/RX-N600D/HTR-N5060/DSP-N6002RX-N600/RX-N600D/HTR-N5060/DSP-N600WALLOUTLETEQUIPMENTUNDER TESTAC LEAKAGETESTER OREQUIVALENTINSULATINGTABLEWARNING: CHEMICAL CONTENT NOTICE!The solder u
10、sed in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (whereapplicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (andpossibly other entities) to cause cancer and/or birth defects or other
11、reproductive harm.DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REA-SON WHATSOEVER!Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or exposeeyes to solder/flux vapor!If you come in contact with sol
12、der or components located inside the enclosure of this product, wash your hands beforehandling food.I TO SERVICE PERSONNEL1. Critical Components InformationComponents having special characteristics are marked sand must be replaced with parts having specifications equalto those originally installed.2
13、. Leakage Current Measurement (For 120V Models Only)When service has been completed, it is imperative to verifythat all exposed conductive surfaces are properly insulatedfrom supply circuits.GMeter impedance should be equivalent to 1500 ohmsshunted by 0.15F.GLeakage current must not exceed 0.5mA.GBe
14、 sure to test for leakage with the AC plug in both polarities.“CAUTION”“F3000, 3001: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE8A, 125V FUSE.”CAUTIONF3000, 3001: REPLACE WITH SAME TYPE 8A, 125V FUSE.ATTENTIONF3000, 3001: UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE DE
15、 8A, 125V.本機搭載基板無鉛付。無鉛種類、修理時下記無鉛使用推奨。Sn+Ag+Cu (錫+銀+銅)Sn+Cu (錫+銅)Sn+Zn+Bi (錫+亜鉛+)注意:無鉛融点温度通常鉛入比3040程度高、合使用。All of the P.C.B.s installed in this unit are soldered usingthe lead free solder.Among some types of lead free solder currently available,it is recommended to use one of the following types for
16、therepair work. Sn + Ag + Cu (tin + silver + copper) Sn + Cu (tin + copper) Sn + Zn + Bi (tin + zinc + bismuth)Caution:As the melting point temperature of the lead free solder isabout 30C to 40C (50F to 70F) higher than that of the leadsolder, be sure to use a soldering iron suitable to each solder.
17、About Lead Free Solder / 無鉛RadioFans.CN 收音机爱 好者资料库RX-N600/RX-N600D/HTR-N5060/DSP-N6003RX-N600/RX-N600D/HTR-N5060/DSP-N600I FRONT PANELSRX-N600 (U, C models)RX-N600 (R, T, K, A, G, E models)RX-N600D (B model)RX-N600/RX-N600D/HTR-N5060/DSP-N6004RX-N600/RX-N600D/HTR-N5060/DSP-N600HTR-N5060 (U, C models
18、)DSP-N600 (J model)HTR-N5060 (A, G models)RX-N600/RX-N600D/HTR-N5060/DSP-N6005RX-N600/RX-N600D/HTR-N5060/DSP-N600RX-N600 (U, C models)I REAR PANELSRX-N600 (R model)RX-N600 (T model)RX-N600/RX-N600D/HTR-N5060/DSP-N6006RX-N600/RX-N600D/HTR-N5060/DSP-N600RX-N600 (K model)RX-N600 (A model)RX-N600 (G, E
19、models)RX-N600/RX-N600D/HTR-N5060/DSP-N6007RX-N600/RX-N600D/HTR-N5060/DSP-N600RX-N600D (B model)HTR-N5060 (U, C models)HTR-N5060 (A model)RX-N600/RX-N600D/HTR-N5060/DSP-N6008RX-N600/RX-N600D/HTR-N5060/DSP-N600HTR-N5060 (G model)DSP-N600 (J model)RX-N600/RX-N600D/HTR-N5060/DSP-N6009RX-N600/RX-N600D/H
20、TR-N5060/DSP-N600I REMOTE CONTROL PANELSRX-N600 (U, C models)HTR-N5060 (U, C models)RX-N600 (R, T, K, A, G, E models)RX-N600D (B model)HTR-N5060 (A, G models)DSP-N600 (J model)RX-N600/RX-N600D/HTR-N5060/DSP-N60010RX-N600/RX-N600D/HTR-N5060/DSP-N600I SPECIFICATIONS / 参考仕様I Audio Section / 部Minimum RM
21、S Output Power / 定格出力RX-N600/RX-N600D(20 Hz to 20 kHz, 0.06 % THD, 8 ohms)FRONT L/R.95 W + 95 WCENTER . 95 WSURROUND L/R .95 W + 95 WSURROUND BACK . 95 WHTR-N5060(1 kHz, 0.7 % THD, 8 ohms)FRONT L/R. 110 W + 110 WCENTER . 110 WSURROUND L/R . 110 W + 110 WSURROUND BACK . 110 WDSP-N600(20 Hz to 20 kHz,
22、 0.09 % THD, 6 ohms)FRONT L/R.95 W + 95 WCENTER . 95 WSURROUND L/R .95 W + 95 WSURROUND BACK . 95 WMaximum Useful Output Power / 実用最大出力 (EIAJ)RX-N600 (R, T, K models)(1 kHz, 10 % THD, 8 ohms)FRONT L/R. 135 WCENTER . 135 WSURROUND L/R . 135 WSURROUND BACK . 135 WDSP-N600 (J model)(1 kHz, 10 % THD, 6
23、ohms)FRONT L/R. 135 WCENTER . 135 WSURROUND L/R . 135 WSURROUND BACK . 135 WDynamic Power Per Channel / (IHF)RX-N600/RX-N600D/HTR-N5060FRONT L/R (8/6/4/2 ohms) . 130/165/195/240 WDSP-N600FRONT L/R (-/6/4/2 ohms).-/135/165/210 WMaximum Output Power / MAX(SP IMPEDANCE SET: 8 ohms minimum/1 kHz, 0.7 %
24、THD, 4 ohms)RX-N600/RX-N600D/HTR-N5060 (B, G, E models)FRONT L/R. 145 W + 145 WCENTER . 145 WSURROUND L/R . 145 W + 145 WSURROUND BACK . 145 WDynamic Headroom / (IHF)RX-N600/HTR-N5060 (U, C models)FRONT L/R (8 ohms) . 1.6 dBIEC Output Power / IEC (1 kHz, 0.06 % THD, 8 ohms)RX-N600/RX-N600D/HTR-N5060
25、 (B, G, E models)FRONT L/R. 105 W + 105 WDamping Factor / FRONT L/R (20 Hz to 20 kHz, 8 ohms) . 120 or moreMaximum Input Voltage / 最大許容入力 (1 kHz, 0.5 % THD)CD, etc. (Effect on).2.2 V or moreFrequency Response / 周波数特性CD, etc. (10 Hz to 100 kHz) . +0/-3.0 dBV-AUX (10 Hz to 20 kHz) . +0/-3.0 dBTotal Ha
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Yamaha-DSPN600-avr-sm 维修电路原理图 Yamaha DSPN600 avr sm 维修 电路 原理图