Yamaha-EMX3000-mix-sm 维修电路原理图.pdf
《Yamaha-EMX3000-mix-sm 维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《Yamaha-EMX3000-mix-sm 维修电路原理图.pdf(82页珍藏版)》请在收音机爱好者资料库上搜索。
1、EMX30001SERVICE MANUALPA01156920010501-135000 1.389K-0221 Printed in Japan 2001.4HAMAMATSU, JAPAN CONTENTSThis document is printed on chlorine free (ECF) paper with soy ink.SPECIFICATIONS. 3/5PANEL LAYOUT. 7CIRCUIT BOARD LAYOUT. 10WIRING. 11DIMENSIONS. 11BLOCK & LEVEL DIAGRAM.12DISASSEMBLY PROCEDURE
2、. 14LSI PIN DESCRIPTION. 17IC BLOCK DIAGRAM. 19CIRCUIT BOARDS. 20INSPECTIONS. 27/33CIRCUIT DIAGRAMS.C1PARTS LIST POWERED MIXERRadioFans.CN 收音机爱 好者资料库EMX30002WARNING: THIS APPARATUS MUST BE EARTHEDIMPORTANTTHE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: GREEN-AND-YELL
3、OW : EARTH BLUE : NEUTRAL BROWN : LIVEAs the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:The wire which is coloured GREEN and YELLOW must be connected to the terminal in the plug whi
4、ch is marked by the letter E or by the safety earth symbol or coloured GREEN and YELLOW.The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.The wire which is coloured BROWN must be connected to the terminal which is marked with the le
5、tter L or coloured RED.* This applies only to products distributed by YAMAHA KEMBLE MUSIC (U.K.) LTD.WARNINGComponents having special characteristics are marked and must bereplaced with parts having specification equal to those originally installed.IMPORTANT NOTICEThis manual has been provided for t
6、he use of authorized Yamaha Retailers and their service personnel. It has been assumedthat basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and under-stood by the users, and have therefore not been restated.WARNING :Failure to follow appropr
7、iate service and safety procedures when servicing this product may result in per-sonal injury, destruction of expensive components and failure of the product to perform as specified. Forthese reasons, we advise all Yamaha product owners that all service required should be performed by anauthorized Y
8、amaha Retailer or the appointed service representative.IMPORTANT :This presentation or sale of this manual to any individual or firm does not constitute authorization certifi-cation, recognition of any applicable technical capabilities, or establish a principal-agent relationship ofany form.The data
9、 provided is belived to be accurate and applicable to the unit(s) indicated on the cover. The research engineering, andservice departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitableand changes in specification are subject to change without
10、 notice or obligation to retrofit. Should any discrepancy appear toexist, please contact the distributors Service Division.WARNING :Static discharges can destroy expensive components. Discharge any static electricity your body may haveaccumulated by grounding yourself to the ground bus in the unit (
11、heavy gauge black wires connect tothis bus.)IMPORTANT :Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply powerto the unit.WARNING: CHEMICAL CONTENT NOTICE!The solder used in the production of this product contains LEAD. In addition, other electrical/electr
12、onic and/or plastic (Whereapplicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possiblyother entities) to cause cancer and/or birth defects or other reproductive harm.DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOU
13、R MOUTH FOR ANY REASON WHATSO EVER!Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or exposeeyes to solder/flux vapor!If you come in contact with solder or components located inside the enclosure of this product, wash your hands before ha
14、ndlingfood.RadioFans.CN 收音机爱 好者资料库EMX30003SPECIFICATIONSGeneral specificationsMaximum output powerSTEREO: 300 W+300 W/4 0.5% THD at 1 kHz215 W+215 W/8 0.5% THD at 1 kHzBRIDGE: 600 W/80.5% THD at 1 kHzFrequency response20 Hz20 kHz +1 dB, 3 dB1 W output into 8(SPEAKER OUT)Channel Gain control at minim
15、um.20 Hz20 kHz +1 dB, 3 dB+4 dB output into 600(ST OUT, MONO OUT, EFFECT SEND, MONITOR OUT)Channel Gain control at minimum.Total harmonic distortionLess than 0.5% 20 Hz20 kHz, 150 W output into 4 (SPEAKER OUT)Less than 0.3% 20 Hz20 kHz, +14 dB output into 600(ST OUT, MONO OUT, EFFECT SEND, MONITOR O
16、UT)Hum & noise(Average, Rs=150 )(with 20 Hz20 kHz BPF)128 dB equivalent input noise63 dB residual output noise (SPEAKER OUT)95 dB residual output noise (ST OUT, MONO OUT, EFFECT SEND, MONITOR OUT)87 dB(ST OUT, MONO OUT)ST master/MONO master fader at maximum level and all channel fader at minimum.64
17、dB (68 dB S/N)(ST OUT, MONO OUT)ST master/MONO master fader and 1 channel fader at maxi-mum level. And 1 channel Gain control at maximum.80 dB(EFFECT SEND, MONITOR OUT)Master fader at maximum level and all channel level control at minimum.Maximum voltage gain91 dBMIC IN to SPEAKER OUT (CH 18)64 dBMI
18、C IN to ST OUT(CH 18)38 dBLINE IN to ST OUT(CH 18)38 dBST IN to ST OUT(CH 9/10, 11/12)70 dBMIC IN to EFFECT SEND (CH 18)64 dBMIC IN to MONITOR OUT (CH 18)Crosstalk at 1 kHz70 dB adjacent input, 70 dB input to outputMIC IN gain control44 dB variablePOWER AMP level control14 dB variableInput channel e
19、qualizationHIGH10 kHzshelving*MID2.5 kHzpeakingLOW100 Hzshelving* Turn over/roll off frequency of shelving: 3 dB below maximum variable level.Meters13 points LED meterCH peak indicatorsRed LED on each channel lits when POST EQ signal reaches the level 3 dB below clipping.LimiterComp. : THD0.5%LIMIT
20、indicatorsTurn on THD0.5%Graphic equalizer7 bands (125, 250, 500, 1k, 2k, 4k, 8k Hz), 12 dB MaximumInternal digital effect16 programs, PARAMETER controlFoot switchDigital effect mute: on/offProtection circuit (Power amp)POWER switch on/off mute, DC detection, TEMP (heatsink temp. 90C)Fan circuitstop
21、 low speed (50C) variable high speed (70C)Phantom power+48 V is supplied to electrically balanced inputs.OptionFC5 (Foot switch)Power requirement/Power consumptionUSA and Canada:120 V AC 60 Hz, 250 WEurope:230 V AC 50 Hz, 300 WOther:240 V AC 50 Hz, 300 WDimensions (WxHxD)480XX125 454 mmWeight16 kgAc
22、cessoriesPower cord, Owners ManualEMX30004Input terminalsGain trimActual load impedanceFor use withnominal Input levelConnectors on mixerSensitivity11. Sensitivity is the lowest level that can produce an output of +4 dB (1.23 V) or the nominal output level when the unit is set at maximum gain. (All
23、fader and level controls are at maximum position.)Max. before clipMIC INPUT (18)MAXMIN5 k50600 Mics60 dB (775 V)16 dB (123 mV)40 dB (7.75 mV)+4 dB (1.23 V)XLR-3-31 type22. Balanced. (T=HOT, R=COLD, S=GND)LINE INPUT (18)MAXMIN50 k600 Lines34 dB (15.5 mV)+10 dB (2.45 V)14 dB (155 mV)+30 dB (24.5 V)PHO
24、NE JACK (TRS)2ST INPUT (912)MAXMIN10 k34 dB (15.5 mV)+10 dB (2.45 V)14 dB (155 mV)+30 dB (24.5 V)PHONE JACK33. Unbalanced.ST SUB IN (1, 2)+4 dB (1.23 V)+20 dB (7.75 V)TAPE IN (L, R)10 dBV (316 mV)+10 dBV (3.16 V)PHONO JACKCH INSERT IN (14)0 dB (775 mV)+20 dB (7.75 V)PHONE JACK (I/O)44. Unbalanced. (
25、T=OUT, R=IN, S=GND)POWER AMP IN (L, R)+4 dB (1.23 V)55. POWER AMP level control= maximum (+4)In these specifications when dB represents a specific voltage, 0 dB is referenced to 0.775 Vrms, 0 dBV is referenced to 1 Vrms.+18 dB (6.16 V)5PHONE JACK3Output terminalsActual source impedanceFor use withno
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Yamaha-EMX3000-mix-sm 维修电路原理图 Yamaha EMX3000 mix sm 维修 电路 原理图