Marantz-MA9S2-pwr-sm 维修电路原理图.pdf
《Marantz-MA9S2-pwr-sm 维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《Marantz-MA9S2-pwr-sm 维修电路原理图.pdf(27页珍藏版)》请在收音机爱好者资料库上搜索。
1、MA-9S2Please use this service manual with referring to the user guide ( D.F.U. ) without fail.ServiceManualMA-9S2 /F N/K1G/N1G/U1GPart no. 90M339J855010First Issue 2006.09MZMonaural Power Amplifi erTABLE OF CONTENTSSECTION PAGE 1. TECHNICAL SPECIFICATIONS . 1 2. CAUTION . 1 3. ALIGNMENTS . 2 4. BLOC
2、K DIAGRAM . 4 5. WIRING DIAGRAM . 5 6. SCHEMATIC DIAGRAM . 7 7. PARTS LOCATION .11 8. EXPLODED VIEW AND PARTS LIST . 23 9. ELECTRICAL PARTS LIST . 27MA-9S2MA-9S2METER OFFOFFONpower on/offmonaural power amplifier ma-9s2power on/offmonaural power amplifier ma-9s2BALANCEDUNBALANCED-2INPUTSELECTOR1Radio
3、Fans.CN 收音机爱 好者资料库MARANTZ DESIGN AND SERVICEUsing superior design and selected high grade components, MARANTZ company has created the ultimate in stereo sound.Only original MARANTZ parts can insure that your MARANTZ product will continue to perform to the specifi cations for which it is famous. Part
4、s for your MARANTZ equipment are generally available to our National Marantz Subsidiary or Agent. ORDERING PARTS : Parts can be ordered either by mail or by Fax. In both cases, the correct part number has to be specifi ed. The following information must be supplied to eliminate delays in processing
5、your order : 1. Complete address 2. Complete part numbers and quantities required 3. Description of parts 4. Model number for which part is required 5. Way of shipment 6. Signature : any order form or Fax. must be signed, otherwise such part order will be considered as null and void.SHOCK, FIRE HAZA
6、RD SERVICE TEST : CAUTION : After servicing this appliance and prior to returning to customer, measure the resistance between either primary AC cord connector pins ( with unit NOT connected to AC mains and its Power switch ON ), and the face or Front Panel of product and controls and chassis bottom.
7、 Any resistance measurement less than 1 Megohms should cause unit to be repaired or corrected before AC power is applied, and verifi ed before it is return to the user/customer. Ref. UL Standard No. 6500.In case of diffi culties, do not hesitate to contact the Technical Department at above mentioned
8、 address. 060607MZUSAMARANTZ AMERICA, INC100 CORPORATE DRIVEMAHWAH, NEW JERSEY 07430USAEUROPE / TRADINGMARANTZ EUROPE B.V.P. O. BOX 8744, BUILDING SILVERPOINTBEEMDSTRAAT 11, 5653 MA EINDHOVENTHE NETHERLANDSPHONE : +31 - 40 - 2507844FAX: +31 - 40 - 2507860AUSTRALIAQualiFi Pty Ltd,24 LIONEL ROAD,MT. W
9、AVERLEY VIC 3149AUSTRALIAPHONE : +61 - (0)3 - 9543 - 1522FAX: +61 - (0)3 - 9543 - 3677NEW ZEALANDWILDASH AUDIO SYSTEMS NZ14 MALVERN ROAD MT ALBERTAUCKLAND NEW ZEALANDPHONE : +64 - 9 - 8451958FAX: +64 - 9 - 8463554THAILANDMRZ STANDARD CO., LTD746 - 754 MAHACHAI ROAD.,WANGBURAPAPIROM, PHRANAKORN,BANGK
10、OK, 10200 THAILANDPHONE : +66 - 2 - 222 9181FAX: +66 - 2 - 224 6795TAIWANPAI- YUING CO., LTD.6 TH FL NO, 148 SUNG KIANG ROAD,TAIPEI, 10429, TAIWAN R.O.C.PHONE : +886 - 2 - 25221304FAX: +886 - 2 - 25630415MALAYSIAWO KEE HONG ELECTRONICS SDN. BHD.2ND FLOOR BANGUNAN INFINITE CENTRELOT 1, JALAN 13/6, 46
11、200 PETALING JAYASELANGOR DARUL EHSAN, MALAYSIAPHONE : +60 - 3 - 7954 8088FAX: +60 - 3 - 7954 7088KOREAMARANTZ KOREA CO., LTD.ROOM 604, ELECTRO OFFICE, 16-58,HANGGANG-RO 3GA, YONGSAN-KU,SEOUL, 140-013, KOREAPHONE : +82 - 2 - 323 - 2155FAX: +82 - 2 - 323 - 2154SINGAPOREWO KEE HONG DISTRIBUTION PTE LT
12、DNo.1 JALAN KILANG TIMOR#08-03 PACIFIC TECH CENTRESINGAPORE 159303PHONE : +65 6376 0338FAX: +65 6376 0166CANADAMARANTZ CANADA INC.5-505 APPLE CREEK BLVD.MARKHAM, ONTARIO L3R 5B1CANADAPHONE : 905 - 415 - 9292FAX: 905 - 475 - 4159JAPAND&M BUILDING, 2-1 NISSHIN-CHO,KAWASAKI-KU, KAWASAKI-SHI,KANAGAWA, 2
13、10-8569 JAPAND&M Holdings Inc.CHINAMARANTZ SHANGHAI TRADING LTD.ROOM.506 SHANGHAI LIGHT INDUSTRY MANSION1578 NANJING (WEST) ROAD SHANGHAICHINATEL: 021 - 6248 - 1064FAX: 021 - 6248 - 3565RadioFans.CN 收音机爱 好者资料库11. TECHNICAL SPECIFICATIONSDIMENSIONS2. CAUTIONThe layout of this amplifier is well concer
14、ned for sound quality.1. When screws and washers are removed, those parts must be set to the same places.2. When wires are removed, the wires must be installed in the same roots, same places.3. Do not hold the side panel (001D/002D) and the bracket (915G) to move the unit when the unit is disassembl
15、ed.Rated power output (20 Hz to 20 kHz) .300 W (8 load) .600 W (4 load)Total harmonic distortion (20 Hz to 20 kHz, 8 load) . 0.01 %Output bandwidth (8 load, 0.05 %) F .5 Hz to 55 kHzFrequency response (1W, 8 load) .3 Hz to 150 kHz (+0 / -3 dB) Damping factor (20 Hz to 20 kHz, 8 load) . 200Inout sens
16、itivity / Inout impedance .1.7 V / 20 k (BALANCED) .1.7 V / 20 k (UNBALANCED)S/N (IHF A network, input shorted) . 123 dB (BALANCED) .123 dB (UNBALANCED)Level of voltage amplification F . 29 dB (BALANCED) F .29 dB (UNBALANCED)Attenuation . 0, -3, -6, -9, -12, - dBSupply voltage /F .100 V AC, 50 / 60
17、Hz /K .220 V AC, 50 / 60 Hz /N .AC 230V 50Hz /U .AC 120V 60HzPower consumption /F .450 W /K/N/U .500W 4 , 600 W driven .1200 WDimensions Width . 459 mm Height . 198 mm Depth . 451 mmWeight . 37.4 kg2. 注意当機音質考慮。1. 類取外場合、元位置取付。2. 類取外場合配線、元通戻。3. 当機分解状態移動、 (001D, 002D) 及 (915G) 持。18459819845120Unit : mm
18、23. ALIGNMENTSAdjustment ProcedureSet the power voltage to rated voltage for this adjustment.DC Offset Voltage Adjustment1. Before turning on power, set the attenuator switch (S201) at , and turn the variable resisters R691 and R692 on the PWB (P691) counterclockwise to the end. Insert digital volta
19、ge meters between the SPEAKERS1 + terminal on the rear panel and the GND terminal of C001/C002, and between the SPEAKERS1 terminal on the rear panel and the GND terminal of C001/C002.2. After the all preparation in Step 1 is done, turn on power. Just after the speaker relays turning on, make the adj
20、ustment to set the offset voltages of the SPEAKERS1 + terminal and the SPEAKERS1 terminal to 0V 20mV. Also, the difference between the offset voltages of the SPEAKERS1 + terminal and the SPEAKERS 1 terminal must be within 3mV. Offset voltage between the SPEAKERS1 + terminal and GND Adjust the variab
21、le resisters R507 on the PWB P501 so that the desired value is obtained. Offset voltage between the SPEAKERS1 terminal and GND Adjust the variable resisters R508 on the PWB P501 so that the desired value is obtained.Idling Current Adjustment1. After DC Offset Voltage Adjustment is completed, adjust
22、the idling current with the variable resisters R691 and R692 on the PWB (P691). The test point uses the 2pin connectors J675 and J677 on the PWB (P671).2. Connect a digital voltage meter in between the 1 pin and the 2 pin of J675 and in between the 1 pin and the 2 pin of J671 each. No. 2 terminal is
23、 + of DC range.3. With seeing the digital voltage meter, turn the variable resisters clockwise slowly to adjust the idling current. Idling current adjustment with R691 R691 is to adjust the idling current for the power transistor(s) on the upper side of the heat sink. Turn R691 clockwise to increase
24、 the idling current. The voltage measured by the digital voltage meter connected to J675 will increase. Idling current adjustment with R692 R692 is to adjust the idling current for the power transistor(s) on the lower side of the heat sink. Turn R692 clockwise to increase the idling current. The vol
25、tage measured by the digital voltage meter connected to J677 will increase.3. ALIGNMENTS調整手順調整時必電源電圧定格電圧合。DC電圧調整1. 電源投入前ATTENUATOR(S201)-、基板(P691)半固定抵抗R691R692反時計方向絞切状態(電流)。 SPEAKERS-1端子C001/C002GND端子間SPEAKERS-1-端子C001/C002GND端子間接続。2. 上記設定後電源投入ON直後、SPEAKERS-1端子SPEAKERS-1端子0V20mV調整。 、端子電圧端子電圧差3mV以内調整
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Marantz-MA9S2-pwr-sm 维修电路原理图 Marantz MA9S2 pwr sm 维修 电路 原理图