HarmanKardon-HKTS7-htss-sm维修电路原理图.pdf

《HarmanKardon-HKTS7-htss-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《HarmanKardon-HKTS7-htss-sm维修电路原理图.pdf（27页珍藏版）》请在收音机爱好者资料库上搜索。

1、harman/kardon SUB-TS7SUB-TS7 (HKTS 7 SUBWOOFER) SERVICE MANUAL harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev1 6/2004 RadioFans.CN 收音机爱 好者资料库 CONTENTS BASIC SPECIFICATIONS . . . . . . . . . . . . . . . . 1 DETAILED SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . .

2、 2 CONTROLS & CONNECTIONS. . . . . . . . . . . . . . 4 SPEAKER CONNECTIONS. . . . . . . . . . . . 6 OPERATION. . . . . . . . . . . . . . .9 BASIC TROUBLESHOOTING GUIDE . . . . . . . . .10 UNIT EXPLODED VIEW. . . . . . . . . . . . . . 11 AMPLIFIER EXPLODED VIEW. . . . . . . . . . . . . . . . 12 TEST

3、SET-UP AND PROCEDURE. . . . . . . . .13 BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 PCB DRAWINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 ELECTRICAL PARTS LIST . . . . . . . . . . . . . . . . . 19 SEMICONDUCTOR PINOUTS . . . . . . . .

4、 . . . . . .23 SCHEMATIC DIAGRAMS . . . . . . . . . . . . . . . . . . .24 PACKAGING. . . . . . . . . . . . . . . . . . . . 26 SPECIFICATIONS Amplifier Power (RMS) 100 Watts Driver 10 woofer, Bass Reflex Enclosure Inputs Stereo Line Level, dedicated Subwoofer (LFE) and Speaker Level with gold-plated

5、binding posts Outputs Speaker Level with gold-plated binding posts Frequency Response 35Hz 120Hz (Filter switch ON) 35Hz 450Hz (Filter switch OFF) Dimensions (H x W x D) 18-7/8 x 13-3/8 x 13-3/8 479mm x 340mm x 340mm Weight 33 lb/15kg Occasional refinements may be made to existing products without n

6、otice but will always meet or exceed original specifications unless otherwise stated. SUB-TS7 SUB-TS7 harman/kardon harman/kardon 1RadioFans.CN 收音机爱 好者资料库SUB-TS7 100W Powered Sub/ Plate AmpLINE VOLTAGEYes/NoHi/Lo LineNom.UnitNotesUS 120vac/60HzYes108-132120VrmsNormal OperationParameterNonimal Specif

7、icationUnitQA Test LimitsConditionsNotesAmp SectionType (Class AB, D, other)ABn/an/aLoad Impedance (speaker)4Ohmsn/aNominalRated Output Power100Watts7550 - 250 Hz, 1 input driven, limiter offTHD Rated Power0.08%0.122k filterTHD 1 Watt0.15%0.522k filterDC Offset5mV-DC30 Speaker OutputsDamping factor1

8、00n/a30Measured at amplifier board Measured at the speaker at speaker output terminals on the amp board.Input SensitivityInput Frequency50Hzn/aNominal Freq.Line (L&R) Input 220mVrms154 - 308 To Rated PowerSingle input drivenSUB (LFE) Input125mVrms87 - 175To Rated PowerSUB (LFE) input driven onlySpea

9、ker/Hi Level Input2.2Vrms1.5 - 3.0To Rated Power(20 dB below Line In), Single input drivenHi Level Max. Input Voltage32Vrms30Nominal Freq., Min. VolumeSignal to NoiseSNR-A-Weighted100dB85relative to rated powerA-Weighting filterSNR-unweighted90dB80relative to rated power22k filterSNR rel. 1W-unweigh

10、ted65dB60relative to 1W Output22k filterResidual Noise Floor1.2mVrms3.0Volume max, using RMS reading DMM/VOM (or A/P)Residual Noise Floor0.8mVrms2.0Volume max, w/ A/P Swept Bandpass Measurement (Line freq.+ harmonics)Input ImpedanceLine Input (L, R,LFE)10Kohmsn/aNominalSpeaker/Hi Level Input4.7Kohms

11、n/aNominalFiltersL&R Fixed Low-Pass Filter170Hz150 - 200 -6dB ref. 100Hz2nd order fixedSUB (LFE) Low pass Filter270Hz240 - 300 -3dB ref. 100Hz2nd order fixedSubsonic filter (HPF) 3rd Order28Hz22 - 28 -3dB ref. 30Hz3rd order fixedLimiter THD at Max. Output Power2.0%5.0FeaturesAuto - On -Off Selection

12、 SwitchYESfunctional Refer to ATO sectionPhase Switch0-180degfunctional Filter On/Off SwitchYESfunctional Volume Pot Taper (Lin/Log)LOGfunctional A TaperSpeaker OutYESfunctional Binding post connector L&R2-Color LED power indicatorYESfunctional Blue: On, Amber: Stand-byPower SwitchYESfunctional Fuse

13、 HolderYESfunctional Input ConfigurationLine In (L,R)YESfunctional Dual RCA jackSUB (LFE)YESfunctional RCA jackSpeaker/Hi Level InYESfunctional Binding post connector L&RSignal Sensing (ATO)Auto-Turn-On (yes/no)YESfunctional Auto - on selection switch in Auto ATO Input test frequency50Hzn/aAuto - on

14、 selection switch in Auto ATO Level Line & SUB Input4.0mV2.0 - 6.0Auto - on selection switch in Auto ATO Level Speaker in40mV25 - 55Auto - on selection switch in Auto ATO Turn-on time5msfunctional Amp connected and AC on, then input signal appliedATO Turn-OFF Time15minutes10 - 20Time before muting,

15、after signal is removedPower on Delay time3sec.functional AC Power AppliedTransients/PopsATO Transient5mV-peak10 Speaker OutputsTurn-on Transient50mV-peak100 Speaker OutputsAC Line cycled from OFF to ON2SUB-TS7 SUB-TS7 harman/kardon harman/kardon ParameterNonimal SpecificationUnitQA Test LimitsCondi

16、tionsNotesTurn-off Transient50mV-peak100 Speaker OutputsAC Line cycled from ON to OFFEfficiencyStand-by Input Power10Watts12 nom. line voltageMaximum allowable input power under nominal input voltage and frequency, in stand-by mode (HOTor COLD operation).Power Consumption rated powe170Watts200 nom.

17、line voltage100 Watts 4.0 ohms and nominal line voltageProtectionShort Circuit Protection YESfunctional Direct short at outputAmplifier should resume operation after short circuit condition is removed. Thermal Protection YESfunctionalAny user accessible metal parts should always remain at 65 degree

18、C or less for domestic version or 55 degree C or less for EU version.DC Offset ProtectionYESfunctional DC present at Speaker Out leadsRelay or crowbar (for driver/fire protection), Primary Fuse RatingUSA-Domestic (120V)2.5Ampsn/aType-T or Slo BloUser-replacable fuse with UL/SEMCO rated holder.3SUB-T

19、S7 SUB-TS7 harman/kardon harman/kardon SUB-TS7 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS 5SUB-TS7 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONSOFFONAUTOONFILTERNORMALREVERSEPHASEINOUTAC 120V60HzPOWERWARNING: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE,REPLACE ONLY WITH SAME TYPE T 2.

20、5A L/250 VOLT FUSEAVERTISSEMENT: UTILISEZ UN FUSIBLE DE RECHANGE DE MEMETYPE T 2.5A L/250VRLLINELEVELINMAXMINIMPORTANT: CONNECT STRIPED WIRETO RED ( ) SPEAKER TERMINAL.LRSUBWOOFERLEVELSUB-TS7For use withHKTS 7 SystemRISK OF ELECTRIC SHO CK DO NO T OPENCAUTI O NRISK OF ELECTRIC SHO CK DO NO T OPENCAU

21、TI O NRISK OF ELECTRIC SHO CK DO NO T OPENHIGH LEVELSUB Subwoofer-Level Control: Volume may be adjusted using the Subwoofer-Level Control.Turn the control clockwise to increase the SUB-TS7s volume, or counterclockwise to decrease it. High-Cut (Low-Pass) Filter Switch:Placing this switch in the ON po

22、sition acti-vates circuitry that cuts out all audio inputsignals above 120Hz.This allows the SUB-TS7 to focus its power on reproducing thelow-frequency portion of the signal, avoidinginefficiency and distortion. Engage this filterwhen using the Speaker-Level Inputs ,or when using the Line-Level Full

23、-RangeInputs , unless your receiver or processorprocesses its line-level output using a low-pass filter.The filter has no effect when theSUB Input is used. Music-Sense On/Off Switch:Whenplaced in the AUTO position,and when theMaster Power Switch is turned on,theSUB-TS7 will automatically turn itself

24、 on orplace itself in the Standby mode,depending onwhether it is receiving an audio signal.Whenthis switch is placed in the ON position,theSUB-TS7 will remain on,whether or not it isreceiving an audio signal.An LED located on top of the SUB-TS7 indi-cates whether the SUB-TS7 is in the ON orSTANDBY s

25、tate when used with the Music-Sense On/Off Switch in the AUTOposition.The LED is lit blue to indicate thatthe SUB-TS7 is receiving an audio signal Subwoofer-Level Control High-Cut (Low-Pass) Filter Switch Music-Sense On/Off Switch Phase Switch Line-Level Subwoofer (SUB) Input Line-Level Full-Range I

26、nputs Speaker-Level Outputs Speaker-Level Inputs Master Power Switch AC Power CordHKTS 7 OM 11/4/03 11:30 AM Page 74 SUB-TS7 SUB-TS7 harman/kardon harman/kardon 6SUB-TS7 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONSSUB-TS7 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONSand is turned on, and

27、the LED is lit amber toindicate that no signal is being received andthe SUB-TS7 is in Standby mode.When the Music-Sense On/Off Switch is in the ON position, the LED will be lit blue, whether or not an audio signal is present.When the Master Power Switch isturned off, the LED goes dark, no matterwhic

28、h position the Music-Sense On/OffSwitch is in. Phase Switch: This switch determineswhether the SUB-TS7 subwoofers piston-like action moves in and out in phase withthe main speakers. If the speakers were toplay out of phase, the sound waves pro-duced by the subwoofer would be cancelledout, reducing b

29、ass response.This phenome-non depends in part on the relative place-ment of the speakers in the room. In mostcases, the Phase Switch should be leftin the NORMAL position. However, itdoes no harm to experiment with the PhaseSwitch , and you may leave it in theposition that maximizes bass response. Li

30、ne-Level Subwoofer (SUB) Input:Connect the subwoofer output of a receiverwith digital surround sound decoding, suchas Dolby* Digital or DTS, to this input.Thisinput bypasses the SUB-TS7s internalcrossover circuitry, and should only be usedwith a filtered signal. If your receiver does nothave digital

31、 decoding,you should use theLine-Level Full-Range Inputs instead. Line-Level Full-Range Inputs: Connectthe line-level subwoofer output or preamp out-put(s) of your receiver or amplifier to theseinputs.If your receiver does not have a sepa-rate subwoofer output,use a Y-adapter (notsupplied) to bridge

32、 the receivers preamp out-put to the main amp input for that channel,and connect the long end of the adapter to the corresponding line-level input on theSUB-TS7.If your receiver has only a singlesubwoofer output,you may connect it to either the left or right line-level input on theSUB-TS7,and no Y-a

33、dapter is needed. Speaker-Level Outputs: If you areusing the Speaker-Level Inputs on theSUB-TS7, you should connect these binding-post terminals to your front left and rightspeakers, remembering to maintain polarityby connecting the (+) terminal on the SUB-TS7 subwoofer to the (+) terminal on thespe

34、aker, and the () terminal on the SUB-TS7 subwoofer to the () terminal on thespeaker. If you are not using the Speaker-Level Inputs , then connect your frontleft and right speakers directly to your receiveror amplifier. See pages 9 through 12 for further information on speaker connections. Speaker-Le

35、vel Inputs: Connect thesebinding-post terminals to the main left andright speaker terminals of your receiver oramplifier, if your receiver or amplifier doesnot have a line-level subwoofer output.Remember to maintain polarity by connectingthe (+) terminal on the receiver/amplifier to the(+) terminal

36、on the SUB-TS7 subwoofer,andthe () terminal on the receiver/amplifier to the() terminal on the SUB-TS7 subwoofer. Master Power Switch: Place thisswitch in the “” position to power-on theSUB-TS7 subwoofer.The SUB-TS7 will thenbe either in the Standby mode or completelyon, depending on the position of

37、 the Music-Sense On/Off Switch . AC Power Cord: Make sure to plug this cord into an active, unswitched electrical out-let for proper operation of the SUB-TS7.The cord should not be plugged into theaccessory outlets found on some audiocomponents.HKTS 7 OM 11/4/03 11:30 AM Page 85 SUB-TS7 SUB-TS7 harm

38、an/kardon harman/kardon 10SPEAKER CONNECTIONSDolby* Digital or DTS(or OtherDigital Surround Mode) ConnectionUSE THIS INSTALLATION METHOD FORDOLBY DIGITAL, DTS OR OTHER DIGITALSURROUND PROCESSORS:Use the line-level input jack marked SUB for the Low-Frequency Effects channel.Connect this jack to the s

39、ubwoofer output or LFE output on your receiver or amplifier.Connect each speaker to the correspondingspeaker terminals on your receiver or amplifier.Make sure youve configured your surroundsound processor for “Subwoofer On. ” Thefront left, front right, center and surroundspeakers should all be set

40、to “Small. ”When all connections have been made, plugthe AC power cord on the subwoofer intoan AC outlet.SPEAKER CONNECTIONSLINE LEVEL INLRSUBSUB/LFE OutSUB-TS7 SubwooferReceiverFrontLeftSurroundLeftFrontRightSurroundRightCenterSurroundRightFrontRightSurroundLeftFrontLeftCenter + + + + +HKTS 7 OM 11

41、/4/03 11:30 AM Page 126 SUB-TS7 SUB-TS7 harman/kardon harman/kardon SPEAKER CONNECTIONS 11Dolby Pro Logic* (Non-Digital) Line LevelUSE THIS INSTALLATION METHOD FORDOLBY PRO LOGIC APPLICATIONS (NOTDOLBY DIGITAL, DTS OR OTHER DIGITALPROCESSING),WHERE THE RECEIVER/PROCESSOR IS EQUIPPED WITH A SUB-WOOFE

42、R OUTPUT, OR A VOLUME-CONTROLLED PREAMP (LINE-) LEVEL OUTPUT:Use the supplied RCA-type interconnectcable to connect the line-level subwooferoutput on your receiveror amplifier to eitherthe left or right Line-Level Full-RangeInput on the SUB-TS7 subwoofer. Useboth the left and right inputs on the sub

43、-woofer if your receiver or processor hasboth left and right line-level outputs. In thatcase, you will need to supply a secondinterconnect cable.If your receiver is equipped with line-level out-puts but does not have a separate subwooferoutput,use a Y-adapter (not supplied) tobridge the receivers pr

44、eamp output to themain amp input for that channel,and connectthe long end of the adapter to the corre-sponding line-level input on the SUB-TS7.IMPORTANT: Do not use the SUB Input on the subwoofer with Dolby Pro Logicprocessors.If your receiver/processor has a built-in low-pass-crossover filter for t

45、he subwoofer out-put, you may use the SUB Input tobypass the subwoofers internal crossover.Connect each speaker to the correspondingspeaker terminals on your receiver or amplifier.Make sure that you have configured yoursurround sound processor for “SubwooferOn. ” The front left, front right, center

46、andsurround speakers should all be set to“Small. ”When all connections have been made, plugthe AC power cord on the subwoofer intoan AC outlet.SPEAKER CONNECTIONSReceiverSUB/LFE OutFrontLeftSurroundLeftFrontRightSurroundRightSUB-TS7SubwooferCenterLine-LevelRL + + + + +SurroundRightFrontRightSurround

47、LeftFrontLeftCenterHKTS 7 OM 11/4/03 11:30 AM Page 137 SUB-TS7 SUB-TS7 harman/kardon harman/kardon 12SPEAKER CONNECTIONSSPEAKER CONNECTIONSFront LeftSurround LeftCenterFront RightSurround RightReceiver + + + + +SUB-TS7SubwooferSurroundRightFrontRightSurroundLeftFrontLeftCenterLRHIGHLEVELDolby Pro Lo

48、gic (Non-Digital) Speaker LevelUSE THIS INSTALLATION METHOD FORDOLBY PRO LOGIC APPLICATIONS (NOTDOLBY DIGITAL, DTS OR OTHER DIGITALPROCESSING),WHERE THE RECEIVER/PROCESSOR DOES NOT HAVE A SUB-WOOFER OUTPUT, OR A VOLUME-CONTROLLED PREAMP (LINE-) LEVEL OUTPUT:Connect your receiver or amplifiers frontl

49、eft and right speaker terminals to the leftand right Speaker-Level Input termi-nals on the SUB-TS7 subwoofer that aremarked “High Level In.” Connect the left andright Speaker-Level Output terminalson the SUB-TS7 subwoofer that are marked“High Level Out” to the corresponding ter-minals on the back of

50、 your front left and rightspeakers.Connect your receiver or amplifiers centerand surround left and right speaker termi-nals to the corresponding terminals on theback of your center, and surround left andright speakers.When all connections have been made,plug the AC power cord on the subwooferinto an