HarmanKardon-AVR2000RDS-avr-sm维修电路原理图.pdf

《HarmanKardon-AVR2000RDS-avr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《HarmanKardon-AVR2000RDS-avr-sm维修电路原理图.pdf（80页珍藏版）》请在收音机爱好者资料库上搜索。

1、AVR2000RDS Audio/Video Receiver DD, DTS, HDCD, MP3 PRELIMINARY SERVICE MANUAL harman/kardon Power for the digital revolution Harman International SNC - Harman Consumer International 2,route de Tours 72500 Chteau du Loir RadioFans.CN 收音机爱 好者资料库TECHNICAL SPECIFICATIONS 2Technical SpecificationsAudio S

2、ectionStereo Mode Continuous Average Power (FTC)50 Watts per channel, 20Hz20kHz, 0.07% THD, both channels driven into 8 ohmsFive-Channel Surround Modes Power Per Individual ChannelFront L&R channels:40 Watts per channel, 0.07% THD, 20Hz20kHz into 8 ohmsCenter channel:40 Watts, 0.07% THD, 20Hz20kHz i

3、nto 8 ohmsSurround channels:40 Watts per channel, 0.07% THD, 20Hz20kHz into 8 ohmsInput Sensitivity/Impedance Linear (High Level)200mV/47kohmsSignal-to-Noise Ratio (IHF-A)95dBSurround System Adjacent Channel Separation Analog Decoding 40dB (Pro Logic, etc.) Dolby Digital (AC-3) 55dB DTS55dBFrequency

4、 Response 1W (+0dB, 3dB)10Hz100kHzHigh Instantaneous Current Capability (HCC)25 AmpsTransient Intermodulation Distortion (TIM)UnmeasurableRise Time16secSlew Rate40V/sec*FM Tuner SectionFrequency Range87.5108MHzUsable SensitivityIHF 1.3 V/13.2dBfSignal-to-Noise RatioMono/Stereo: 70/65dB (DIN)Distorti

5、onMono/Stereo: 0.15/0.3%Stereo Separation35dB 1kHzSelectivity300kHz: 65dBImage Rejection80dBIF Rejection90dBAM Tuner SectionFrequency Range5201611kHzSignal-to-Noise Ratio45dBUsable SensitivityLoop: 500VDistortion1kHz, 50% Mod: 0.8%Selectivity9kHz: 30dBVideo SectionVideo FormatPAL/NTSCInput Level/Imp

6、edance1Vp-p/75 ohmsOutput Level/Impedance 1Vp-p/75 ohmsVideo Frequency Response10Hz8MHz (3dB)GeneralPower RequirementAC 220-240V/50HzPower Consumption72W idle, 470W maximum Dimensions (Max)Width440mm Height167mm Depth435mm Weight14.0 kgDepth measurement includes knobs, buttons and terminal connectio

7、ns.Height measurement includes feet and chassis.All features and specifications are subject to change without notice.Harman Kardon is a registered trademark, and Power for the digital revolution is atrademark, of Harman International Industries, Inc.*Manufactured under license from Dolby Laboratorie

8、s.“Dolby,”“Pro Logic,”“AC-3” and the Double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. 19921999 Dolby Laboratories, Inc.All rights reserved.DTS and DTS Surround are trademarks of Digital Theater Systems, Inc. UltraStereo is a trademark of UltraStereo Corp.VMAx is

9、a trademark of Harman International Industries, Inc., and is an implementation of Cooper Bauck Transaural Stereo under patent license.Logic 7 is a registered trademark of Lexicon, Inc.Crystal is a registered trademark of Cirrus Logic Corp.*Without input anti slewing and output isolation networks.Rad

10、ioFans.CN 收音机爱 好者资料库FRONT PANEL CONTROLS 31Main Power Switch: Press this button toapply power to the AVR 2000.When the switchis pressed in, the unit is placed in a Standbymode, as indicated by the amber LED 3sur-rounding the System Power Control2.Thisbutton MUST be pressed in to operate the unit.To

11、turn the unit off completely and prevent theuse of the remote control, this switch should bepressed until it pops out from the front panelso that the word “OFF” may be read at the topof the switch.NOTE:This switch is normally left in the “ON”position.2System Power Control:When the MainPower Switch1i

12、s “ON,” press this button toturn on the AVR 2000; press it again to turn theunit off (to Standby). Note that the PowerIndicator surrounding the switch 3will turngreen when the unit is on.3Power Indicator:This LED will be illumi-nated in amber when the unit is in the Standbymode to signal that the un

13、it is ready to beturned on.When the unit is in operation, theindicator will turn green.4Headphone Jack:This jack may be used tolisten to the AVR 2000s output through a pairof headphones. Be certain that the headphoneshave a standard 6.3 mm stereo phone plug.Note that the speakers will automatically

14、beturned off when the headphone jack is in use.5Selector Buttons:When you are establish-ing the AVR 2000s configuration settings,usethese buttons to select from the choices available,as shown in the Main Information Display.6Tone Mode: Pressing this button enables ordisables the Balance, Bass and Tr

15、eble tone con-trols.When the button is pressed so that thewords TONE INappear in the MainInformation Display, the settings of theBassand Treble*controls and of theBalance control &will affect the output sig-nals.When the button is pressed so that thewords TONE OUT appear in the MainInformation Displ

16、ay, the output signalwill be “flat, ” without any balance, bass or treblealteration.Front Panel Controls1234 5 67 8 9 )! # $ % & * ( Main Power SwitchSystem Power ControlPower IndicatorHeadphone JackSelector ButtonsTone ModeSurround Mode SelectorTuningTuner Band SelectorPreset Stations SelectorInput

17、 Source SelectorRDS Select ButtonDigital Optical 3 InputDigital Coax 3 InputVideo 4 input jacksBass ControlBalance ControlTreble ControlVolume ControlSet ButtonInput IndicatorsDelayDigital Input SelectorMain Information DisplayChannel Select ButtonSpeaker Select ButtonTest Tone SelectorSurround Mode

18、 IndicatorsRemote Sensor Window4135789)!#$%*&(2926AVR 2000 RDSRDSPTYCTRTTA4 FRONT PANEL CONTROLSFront Panel Controls7Surround Mode Selector: Press this but-ton to change the surround mode by scrollingthrough the list of available modes. Note thatDolby Digital and DTS modes can be selectedonly when a

19、 digital input is used (See page 24for more information about surround modes.)8Tuning Selector: Press the left side of thebutton to tune lower frequency stations and theright side of the button to tune higher frequencystations.When a station with a strong signal isreached, the TUNED indicator Vwill

20、illuminatein the Main Information Display (see page 29 for more information on tuningstations).9Tuner Band Selector: Pressing this buttonwill automatically switch the AVR to the Tunermode. Pressing it again will switch between theAM and FM frequency bands, holding it pressedfor some seconds will swi

21、tch between stereoand mono receiving and between automatic andmanual tuning mode (See page 29 for moreinformation on the tuner).)Preset Stations Selector: Press this but-ton to scroll up or down through the list of sta-tions that have been entered into the presetmemory. (See page 29 for more informa

22、tion ontuner programming.)!Input Source Selector: Press this buttonto change the input by scrolling through the listof input sources. RDS Select Button: Press this button to dis-play the various messages that are part of theRDS data system of the AVR 2000s tuner.(Seepage 30 for more information on R

23、DS).#Digital Optical 3 Input: Connect the opti-cal digital audio output of an audio or video prod-uct to this jack.When the Input is not in use,becertain to keep the plastic cap installed to avoiddust contamination that might degrade future performance.$Digital Coax 3 Input:This jack is normallyused

24、 for connection to the output of portabledigital audio devices, video game consoles orother products that have a coax digital jack.%Video 4 Input Jacks: These audio/videojacks may be used for temporary connection tovideo games or portable audio/video productssuch as camcorders and portable audio pla

25、yers.Bass Control:Turn this control to modify thelow frequency output of the left/right channels byas much as 10dB.Set this control to a suitableposition for your taste or room acoustics.&Balance Control:Turn this control tochange the relative volume for the frontleft/right channels.NOTE: For proper

26、 operation of the surroundmodes this control should be at the midpoint or“12 oclock” position.*Treble Control:Turn this control to modifythe high frequency output of the left/right chan-nels by as much as 10dB.Set this control to asuitable position for your taste or room acoustics.(Volume Control:Tu

27、rn this knob clockwiseto increase the volume, counterclockwise todecrease the volume. If the AVR is muted,adjusting volume control will automaticallyrelease the unit from the silenced condition.Set Button:When making choices duringthe setup and configuration process,press thisbutton to enter the des

28、ired setting as shown inthe Main Information Display into theAVR 2000s memory.The set button may also beused to change the display brightness.(See page 28.)Input indicators: A green LED will light infront of the input that is currently being used asthe source for the AVR 2000.Delay: Press this butto

29、n to begin thesequence of steps required to enter delay timesettings. (See page 20 for more information ondelay times.)Digital Input Selector:When playing asource that has a digital output, press thisbutton to select between the Optical# ?and Coaxial$ ?Digital inputs. (See pages 25-27 for more infor

30、mation on digital audio.)Main Information Display:This displaydelivers messages and status indications to helpyou operate the receiver. (See pages 78 for acomplete explanation of the InformationDisplay.)Channel Select Button: Press this buttonto begin the process of trimming the channeloutput levels

31、 using an external audio source.(For more information on output level trimadjustment, see page 28.)Speaker Select Button: Press this buttonto begin the process of selecting the speakerpositions that are used in your listening room.(See page 19 for more information on setup andconfiguration.)Test Ton

32、e Selector: Press this button tobegin the process of adjusting the channel out-put levels using the internal test tone as a refer-ence. (For more information on output leveladjustment, see page 21.)Surround Mode Indicators: A green LEDwill light in front of the surround mode that iscurrently in use.

33、Remote Sensor Window:The sensorbehind this window receives infrared signalsfrom the remote control.Aim the remote at thisarea and do not block or cover it unless anexternal remote sensor is installed.ABCDEFGHIJKLMNOPQRRTUVWXAA ABACADAEFRONT PANEL INFORMATION DISPLAY 5Front Panel Information DisplayC

34、OAXIALTHEATER5 CH STEREOHALL 3-STEREOPRO LOGICDIGITALDTSDOLBY DPCMMP3NIGHTOPTICALANALOGLFE0CL0123123MEMORYPRESETSLEEPAUTO5.1 LOGIC 7 CMVMAx NFMUTETUNEDSTABD EMNKLSTRQPXW V UFHIJOOROOLSOORSOOCGRDSA EPTYA DCTA CRTA BTAA AOBitstream IndicatorsOptical Source IndicatorsDTS Mode IndicatorDolby Digital Ind

35、icatorCoaxial Source IndicatorsDolby Pro Logic IndicatorAnalog Input IndicatorDolby 3 Stereo IndicatorVMAx Mode Indicator5 Channel Stereo IndicatorLogic 7 Mode IndicatorsHall Mode IndicatorTheater Mode IndicatorNight Mode IndicatorMute IndicatorSpeaker/Channel Input IndicatorsPreset Number/Sleep Tim

36、erPreset IndicatorSleep IndicatorMemory IndicatorStereo IndicatorTuned IndicatorAuto IndicatorMain Information DisplayTraffic IndicatorRadiotext IndicatorClock Timer IndicatorProgram Type IndicatorRDS IndicatorABitstream Indicators:When the input is adigital source,one of these indicators will light

37、 todisplay the specific type of signal in use.BOptical Source Indicators:These indica-tors light to show when a Optical Digital Inputhas been selected.CDTS Mode Indicator:This indicator illumi-nates when the DTS mode is selected.DDolby Digital Indicator:This indicator illu-minates when Dolby Digital

38、 mode is selected.ECoaxial Source Indicators:These indica-tors light to show when a Coaxial Digital Inputhas been selected.FDolby Pro Logic Indicator:This indicatorlights when the Dolby ProLogic mode has beenselected.GAnalog Input Indicator:This indicatorlights when an analog input source has beense

39、lected.HDolby 3 Stereo Indicator:This indicatorlights when the Dolby 3 Stereo Mode has beenselected.IVMAx Mode Indicator:This indicator illu-minates to show that the VMAx mode is in use.VMAx F appears when the Far Field VMAxmode is selected; VMAx N appears when theNear Field VMAx mode is selected. (

40、See page 24for a description of the VMAx Modes.)J5 Channel Stereo Indicator:This indica-tor lights when the 5 Channel Stereo mode hasbeen selected.KLogic 7 Mode Indicators:These indicatorsilluminate when the Logic 7 mode is in use.LOGIC 7C appears for the Cinema versionof Logic 7, LOGIC 7M appears f

41、or theMusic version of Logic 7. (See page 24 for adescription of the Logic 7 Modes.)LHall Mode Indicator: This indicator lightswhen the Hall mode has been selected.MTheater Mode Indicator:This indicator illu-minates to show that the Theater mode is in use.NNight Mode Indicator:This indicatorlights w

42、hen the AVR 2000 is in the Night mode,which preserves the dynamic range of digitalprogram material at low volume levels.OMute Indicator:This indicator illuminatesto remind you that the AVR 2000s output hasbeen silenced by pressing the Mute button?. Press the Mute button again to return tothe previou

43、sly selected output level.PSpeaker/Channel Input Indicators:Theseindicators are multipurpose,indicating either thespeaker type selected for each channel or theincoming data-signal configuration.The left,cen-ter,right,right surround and left surround speakerindicators are composed of three boxes,whil

44、e thesubwoofer is a single box.The center box lightswhen a “Small”speaker is selected,and the twoouter boxes light when “Large”speakers areselected.When none of the boxes are lit for thecenter,surround or subwoofer channels,nospeaker has been selected for that position.(Seepage 18 for more informati

45、on on configuringspeakers.) The letters inside each of the centerboxes display active input channels.For standardanalog inputs,only the L and R will light,indicat-ing a stereo input.When a digital source is play-ing,the indicators will light to display the chan-nels begin received at the digital inp

46、ut.When theletters flash,the digital input has been interrupt-ed.(See page 26 for more information on theChannel Indicators).QPreset Number/Sleep Timer: When thetuner is in use, these numbers indicate the spe-cific preset memory location in use. (See page 29for more information on preset stations.)

47、Whenthe Sleep function is in use, these numbers showhow many minutes remain before the unit goesinto the Standby mode.6 FRONT PANEL INFORMATION DISPLAYFront Panel Information DisplayRPreset Indicator:This indicator lights whenthe tuner is in use to show that the PresetNumber/Sleep TimerQis showing t

48、he sta-tions preset memory number. (See page 29 formore information on tuner presets.)SSleep Indicator:This indicator lights whenthe Sleep function is in use.The numbers in thePreset/Sleep Number Indicators will show theminutes remaining before the AVR 2000 goesinto the Standby mode. (See page 23 fo

49、r moreinformation on the Sleep function.)TMemory Indicator:This indicator flasheswhen entering presets and other informationinto the tuners memory.UStereo Indicator:This indicator illuminateswhen an FM station is being tuned in stereo.VTuned Indicator:This indicator illuminateswhen a station is bein

50、g received with sufficient sig-nal strength to provide acceptable listening quality.WAuto Indicator:This indicator illuminateswhen the tuners Auto mode is in use.XMain Information Display:This displayshows messages relating to the status, inputsource, surround mode, tuner, volume level orother aspec