HarmanKardon-AVR330MK3-avr-sm维修电路原理图.pdf

《HarmanKardon-AVR330MK3-avr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《HarmanKardon-AVR330MK3-avr-sm维修电路原理图.pdf（130页珍藏版）》请在收音机爱好者资料库上搜索。

1、 harman/kardon AVR330 AVR330 7 X 55W 7.1 CHANNEL A/V RECEIVER SERVICE MANUAL CONTENTS ESD WARNING.2 LEAKAGE TESTING.3 BASIC SPECIFICATIONS.4 FRONT PANEL CONTROLS.5 REAR PANEL CONNECTIONS.7 REMOTE CONTROL FUNCTIONS.10 TROUBLESHOOTING GUIDE.14 PROCESSOR RESET.14 DISASSEMBLY.15 BULLETIN HK2003-10.16 TE

2、CH TIP HKTT2004-0318 TECH TIP HKTT2003-01.22 UNIT EXPLODED VIEW.23 BLOCK DIAGRAM.24 AMP BIAS ADJUSTMENT.25 PCB DRAWINGS.27 ELECTRICAL PARTS LIST.32 SEMICONDUCTOR PINOUTS.72 SCHEMATICS113 WIRING DIAGRAM.129 PACKAGING.130 harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev3 4/2007

3、RadioFans.CN 收音机爱 好者资料库Eachprecautioninthismanualshouldbefollowedduringservicing.Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a component identified with, use only the replacement parts designated, or parts with the same ratings or res

4、istance, wattage, or voltage that are designated in theparts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptablyinsulated from the supply circuit before retuming the product to the customer.Some semiconductor (solid state) devic

5、es can be damaged easily by static electricity. Such components commonly are calledElectrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors andsemiconductor chip components.The following techniques should be used to help reduc

6、e the incidence of component damage caused by static electricity.1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge onyour body by touching a known earth ground. Alternatively, obtain and wear a commercially available dis

7、charging wrist strap device,which should be removed for potential shock reasons prior to applying power to the unit under test.2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, toprevent electrostatic charge build-up

8、or exposure of the assembly.3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can generate electrical chargessufficient to damage ES devices.5. Do not use freon-propel

9、led chemicals. These can generate electrical change sufficient to damage ES devices.6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacementES devices are packaged with leads electrically shorted together by conducti

10、ve foam, aluminum foil or comparable conductive material.)7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to thechassis or circuit assembly into which the device will be installed.Be sure no power is applied to the chass

11、is or circuit, and observe all other safety precautions.8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing togetheror your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity suffici

12、ent to damage an ES devices.CAUTION :AVR330 AVR330 harman/kardon RadioFans.CN 收音机爱 好者资料库2SAFETY PRECAUTIONSThe following check should be performed for the continuedprotection of the customer and service technician.LEAKAGE CURRENT CHECKMeasure leakage current to a known earth ground (waterpipe, condu

13、it, etc.) by connecting a leakage current testerbetween the earth ground and all exposed metal parts of theappliance (input/output terminals, screwheads, metaloverlays, control shaft, etc.). Plug the AC line cord of theappliance directly into a 120V AC 60Hz outlet and turn theAC power switch on. Any

14、 current measured must not exceedo.5mA.ANY MEASUREMENTS NOT WITHIN THE LIMITSOUTLINED ABOVE ARE INDICATIVE OF APOTENTIAL SHOCK HAZARD AND MUST BECORRECTED BEFORE RETURNING THE APPLIANCETO THE CUSTOMER.DeviceundertestTest allexposed metalsurfacesAlso test withplug reversed(Using AC adapterplug as req

15、uired)AC Leakage TestLeakagecurrenttesterReading shouldnot be above0.5mAEarthgroundAVR330 AVR330 harman/kardon 3TECHNICAL SPECIFICATIONS 4AVR 330 TECHNICAL SPECIFICATIONSAudio SectionStereo Mode Continuous Average Power (FTC)65 Watts per channel, 20Hz20kHz, 0.07% THD, both channels driven into 8 ohm

16、sSeven-Channel Surround Modes Power per Individual ChannelFront L&R channels:55 Watts per channel 0.07% THD, 20Hz20kHz into 8 ohmsCenter channel:55 Watts 0.07% THD, 20Hz20kHz into 8 ohmsSurround (L & R side, L & R back) channels:55 Watts per channel 0.07% THD, 20Hz20kHz into 8 ohmsInput Sensitivity/

17、ImpedanceLinear (High-Level)200mV/47k ohmsSignal-to-Noise Ratio (IHF-A)100dBSurround System Adjacent Channel SeparationPro Logic I/II 40dBDolby Digital (AC-3)55dBDTS55dBFrequency Response 1W (+0dB, 3dB)10Hz 130kHzHigh Instantaneous Current Capability (HCC)35 AmpsTransient Intermodulation Distortion

18、(TIM)UnmeasurableSlew Rate40V/secFM Tuner SectionFrequency Range87.5108.0MHzUsable SensitivityIHF 1.3V/13.2dBfSignal-to-Noise RatioMono/Stereo 70/68dBDistortionMono/Stereo 0.2/0.3%Stereo Separation40dB 1kHzSelectivity400kHz, 70dBImage Rejection80dBIF Rejection90dBAM Tuner SectionFrequency Range33017

19、10kHzSignal-to-Noise Ratio45dBUsable SensitivityLoop 500VDistortion1kHz, 50% Mod 0.8%Selectivity10kHz, 30dBVideo SectionTelevision FormatNTSCInput Level/Impedance1Vp-p/75 ohmsOutput Level/Impedance1Vp-p/75 ohmsVideo Frequency Response (Composite and S-Video)10Hz8MHz (3dB)Video Frequency Response (Co

20、mponent Video) 10Hz30MHz (3dB)GeneralPower RequirementAC 120V/60HzPower Consumption118W idle, 890W maximum (7 channels driven)Dimensions (Product)(Shipping)Width17.3 inches (440mm)21.5 inches (545mm)Height6.6 inches (168mm)9.9 inches (251mm)Depth15 inches (381mm)17.9 inches (455mm)Weight(Product)(Sh

21、ipping)30.6 lb (13.9kg)35.2 lb (16kg)Depth measurement includes knobs, buttons and terminal connections.Height measurement includes feet and chassis.All features and specifications are subject to change without notice.Harman Kardon and Power for the Digital Revolution are registered trademarks of Ha

22、rman International Industries, Incorporated.is a trademark of Harman International Industries, Incorporated (patent no. 5,386,478).*Manufactured under license from Dolby Laboratories.“Dolby,”“Pro Logic” and the Double-D symbol are trademarks of Dolby Laboratories.DTS, DTS Surround, DTS-ES and DTS Ne

23、o:6 are registered trademarks of Digital Theater Systems, Inc.VMAx is a registered trademark of Harman International Industries, Incorporated, and is an implementation of Cooper Bauck Transaural Stereo under patent license.Logic 7 is a registered trademark of Harman International Industries, Incorpo

24、rated.TMTECHNICAL SPECIFICATIONS AVR330 AVR330 harman/kardon 4FRONT-PANEL CONTROLS1 Main Power Switch: Press this button to applypower to the AVR 330. When the switch is pressedin, the unit is in a Standby mode, as indicated by theamber LED 2 above the Standby/On Switch 3.This button MUST be pressed

25、 in to operate the unit.To turn the unit off and prevent the use of the remotecontrol, this switch should be pressed until it popsout from the front panel and the word “OFF” is seenat the top of the switch.NOTE: This switch is normally left in the “ON” position.2 Power Indicator: This LED lights amb

26、er when theunit is in the Standby mode to signal that the AVR isready to be turned on.When the unit is in operation,the indicator is blue.3 Standby/On Switch: When the Main PowerSwitch 1 is “ON,” press this button to turn on theAVR 330; press it again to turn the unit off.The PowerIndicator 3 turns

27、blue when the unit is on.4 Headphone Jack: This jack may be used to listento the AVR 330s output through a pair of headphones.The speakers will automatically be turned off when theheadphone jack is in use.5 Tone Mode: Pressing this button enables or dis-ables the Bass and Treble tone controls.When t

28、he but-ton is pressed so that TONE IN appears in theLower Display Line , the Bass and Treble controls may be used to adjust the output signals.When the button is pressed once or twice so that thewords TONE OUT appear in the Lower DisplayLine , the output signal will be “flat, ” no matter howthe actu

29、al Bass and Treble Controls areadjusted.6 Speaker Select Button: Press this button tobegin the process of configuring the unit to match thetype of speakers used in your listening room. (Seepages 17 and 2022 for more information on speakersetup and configuration.)7 Surround Mode Group Selector: Press

30、 this but-ton to select the top-level group of surround modes.Each press of the button will select the current or lastused mode in each of the surround mode groups(e.g., Dolby, DTS, DTS Neo:6, Logic 7, DSP, Stereo).When the button is pressed so that the name of thedesired surround mode group appears

31、 in the on-screen display and in the Lower Display Line ,press the Surround Mode Selector 8 to cyclethrough the individual modes available. For example,press this button to select Dolby modes, and thenpress the Surround Mode Selector 8 to choosefrom the various mode options.8 Surround Mode Selector:

32、 Press this button to select from among the available surround mode1 Main Power Switch2 Power Indicator 3 Standby/On Switch4 Headphone Jack5 Tone Mode 6 Speaker Selector7 Surround Mode Group Selector8 Surround Mode Selector9 Tuning Selector)/Buttons! Tuner Band Selector Set Button# Digital Input Sel

33、ector$ Preset Station Selector% Delay Adjust Selector Input Source Selector& Tuner Mode Selector * Optical 3 Digital Input( Coaxial 3 Digital Input Video 4 Video Input Jacks Video 4 Audio Input Jacks Bass Control Balance Control Treble Control Channel Adjust Selector Volume Control Input Indicators

34、Speaker/Channel Input Indicators Upper Display Line Lower Display Line Surround Mode Indicators Remote Sensor WindowDIGITALLOGIC 7VID 1DVDCDFMAMTAPE68CHVID 2VID 3VID 4PRO LOGIC 3 STEREO DSP5 CH. STEREOSURR. OFF1267#(*8)!)&%3459$FRONT-PANEL CONTROLSFRONT-PANEL CONTROLS 5 5NOTE: To make it easier to f

35、ollow the instructions that refer to this illustration, a larger copy may be downloaded from the Product Support section for this productat .AVR330 AVR330 harman/kardon 5options for the mode group selected.The specificmodes will vary based on the number of speakersavailable, the mode group and if th

36、e input source isdigital or analog. For example, press the SurroundMode Group Selector 7 to select a mode groupingsuch as Dolby or Logic 7, and then press this buttonto see the specific mode choices available. For moreinformation on mode selection, see page 26.9 Tuning Selector: Press the left side

37、of the buttonto tune lower-frequency stations and the right side ofthe button to tune higher-frequency stations.When thetuner is in the Manual mode, each tap will increase ordecrease the frequency by one increment.When thetuner receives a strong enough signal for adequatereception, MANUAL TUNED will

38、 appear in theon-screen display and the Lower Display Line.When the tuner is in the Auto mode, press the buttononce, and the tuner will scan for a station with accept-able signal strength.When the next station with astrong signal is tuned the scan will stop andthe on-screen display and the Lower Dis

39、play Linewillindicate AUTO TUNED.When an FM Stereo sta-tion is tuned, the display will read AUTO STTUNED.To switch back and forth between the Auto andManual tuning modes, press the Tuning ModeSelector &.)/Buttons: When configuring the AVR 330ssettings,use these buttons to select from the availablech

40、oices.! AM/FM Selector: Press this button to turn theAVR on and to select the Tuner as the input source.Press it again to switch between the AM and FM fre-quency bands. (See page 29 for more information onthe tuner.) Set Button: When making choices during thesetup and configuration process, press th

41、is button to enter the desired setting into the AVR 330s memory.# Digital Input Selector: Press this button toselect one of the digital inputs or the analog input forany source. (See pages 2629 for more informationon digital audio.)$ Preset Station Selector: Press this button toscroll up or down thr

42、ough the list of stations that havebeen entered into the preset memory. (See page 29for more information on tuner presets.)% Delay Adjust Selector: Press this button tobegin the steps required to enter delay settings. (Seepage 22 for more information on delay times.) Input Source Selector: Press thi

43、s button tochange the input by scrolling up or down through thelist of Input Indicators .& Tuner Mode Selector: Press this button to selectAuto or Manual tuning.When the button is pressed sothat AUTO appears in the Lower Display Line ,the tuner will search for the next station with an accept-able si

44、gnal when the Tuning Selector 9uis pressed.When the button is pressed so that MANUAL appears in the Lower Display Line ,each press of the Tuning Selector 9u willincrease the frequency.This button may also be used toswitch between Stereo and Mono modes for FM radioreception.When weak reception is enc

45、ountered, pressthe button so that MANUAL appears in the LowerDisplay Line and on the on-screen display toswitch to Mono reception. Press it again to switch backto Stereo mode. (See page 29 for more information onusing the tuner.)* Optical 3 Digital Input: Connect the optical digitalaudio output of a

46、n audio or video product to this jack.When the input is not in use, be certain to keep theplastic cap installed to avoid dust contamination thatmight degrade future performance.( Coaxial 3 Digital Input: This jack is used forconnection to the output of portable audio devices,video game consoles or o

47、ther products that have acoax digital audio jack. Video 4 Video Input Jacks: These jacks may beused for temporary connection to the composite or S-Video output of video games, camcorders or otherportable video products.You may make a connectionto either jack at any time, but not to both simultane-ou

48、sly. Video 4 Audio Input Jacks: These audio jacksmay be used for temporary connection to videogames or portable audio/video products such as cam-corders and portable audio players. Bass Control:Turn this control to modify the low-frequency output of the left/right channels by as much as10dB. Balance

49、 Control: Turn this control to change therelative volume for the front left/right channels.NOTE: For proper operation of the surround modesthis control should be at the midpoint or “12 oclock”position.Treble Control:Turn this control to modify the highfrequency output of the left/right channels by a

50、s much as10dB. Channel Adjust Selector: Press this button tobegin the process of trimming the channel output lev-els using an external audio source. (For more informa-tion on output level trim adjustment, see page 30.) Volume Control: Turn this knob clockwise toincrease the volume, counterclockwise