HarmanKardon-AVR145-avr-sm维修电路原理图.pdf

《HarmanKardon-AVR145-avr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《HarmanKardon-AVR145-avr-sm维修电路原理图.pdf（135页珍藏版）》请在收音机爱好者资料库上搜索。

1、 harman/kardon AVR145 AVR145 5 X 40W 5.1 CHANNEL A/V RECEIVER SERVICE MANUAL CONTENTSESD WARNING.2ELECTRICAL PARTS LIST.12LEAKAGE TESTING.3SEMICONDUCTOR PINOUTS48BASIC SPECIFICATIONS.4PCB DRAWINGS.119TROUBLESHOOTING GUIDE.5BLOCK DIAGRAM.126PROCESSOR RESET.5WIRING DIAGRAM.127PACKAGE LIST AND PARTS.6A

2、MP BIAS ADJUSTMENT128DISASSEMBLY7SCHEMATIC DIAGRAMS.129UNIT EXPLODED VIEW AND PARTS11Released 2007Discontinued XXXXRev 0, 10/2007harman/kardon, Inc.250 Crossways Park Dr.Woodbury, New York, 11797harman/kardonAVR 145/230 service manualPage 1 of 135RadioFans.CN 收音机爱 好者资料库Eachprecautioninthismanualshou

3、ldbefollowedduringservicing.Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a component identified with, use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in t

4、heparts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptablyinsulated from the supply circuit before retuming the product to the customer.Some semiconductor (solid state) devices can be damaged easily by static electricity. Such

5、components commonly are calledElectrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors andsemiconductor chip components.The following techniques should be used to help reduce the incidence of component damage caused by static

6、electricity.1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge onyour body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device,which should be removed f

7、or potential shock reasons prior to applying power to the unit under test.2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, toprevent electrostatic charge build-up or exposure of the assembly.3. Use only a grounded-ti

8、p soldering iron to solder or unsolder ES devices.4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can generate electrical chargessufficient to damage ES devices.5. Do not use freon-propelled chemicals. These can generate electrical change s

9、ufficient to damage ES devices.6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacementES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive mater

10、ial.)7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to thechassis or circuit assembly into which the device will be installed.Be sure no power is applied to the chassis or circuit, and observe all other safety precautio

11、ns.8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing togetheror your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices.CAUTION : AVR145 harman/k

12、ardonharman/kardon harman/kardonAVR 145/230 service manualPage 2 of 135RadioFans.CN 收音机爱 好者资料库2ELECTROSTATICALLY SENSITIVE DEVICESSAFETY PRECAUTIONSThe following check should be performed for the continuedprotection of the customer and service technician.LEAKAGE CURRENT CHECKMeasure leakage current

13、to a known earth ground (waterpipe, conduit, etc.) by connecting a leakage current testerbetween the earth ground and all exposed metal parts of theappliance (input/output terminals, screwheads, metaloverlays, control shaft, etc.). Plug the AC line cord of theappliance directly into a 120V AC 60Hz o

14、utlet and turn theAC power switch on. Any current measured must not exceedo.5mA.ANY MEASUREMENTS NOT WITHIN THE LIMITSOUTLINED ABOVE ARE INDICATIVE OF APOTENTIAL SHOCK HAZARD AND MUST BECORRECTED BEFORE RETURNING THE APPLIANCETO THE CUSTOMER.DeviceundertestTest allexposed metalsurfacesAlso test with

15、plug reversed(Using AC adapterplug as required)AC Leakage TestLeakagecurrenttesterReading shouldnot be above0.5mAEarthgroundharman/kardonAVR 145/230 service manualPage 3 of 135Technical Specifications AVR145/230Audio SectionStereo Mode Continuous Average Power (FTC)50Watts per channel, 20Hz20kHz, 0.

16、07% THD, both channels driven into 8 ohms5 Channel Surround Modes Power Per Individual ChannelFront L&R channels:40Watts per channel, 0.07% THD, 20Hz20kHz into 8 ohmsCenter channel:40Watts, 0.07% THD, 20Hz20kHz into 8 ohmsSurround channels:40Watts per channel, 0.07% THD, 20Hz20kHz into 8 ohmsInput S

17、ensitivity/Impedance Linear (High Level)200mV/47kohmsSignal-to-Noise Ratio (IHF-A)100dBSurround System Adjacent Channel Separation Analog Decoding 40dB (Pro Logic, etc.) Dolby Digital (AC-3) 55dB DTS55dBFrequency Response 1W (+0dB, 3dB)10Hz130kHzHigh Instantaneous Current Capability (HCC)25AmpsTrans

18、ient Intermodulation Distortion (TIM)UnmeasurableRise Time16secSlew Rate40V/sec*FM Tuner SectionFrequency Range87.5108MHzUsable SensitivityIHF 1.3 V/13.2dBfSignal-to-Noise RatioMono/Stereo: 70/68dB (DIN)DistortionMono/Stereo: 0.2/0.3%Stereo Separation40dB 1kHzSelectivity400kHz: 70dBImage Rejection80

19、dBIF Rejection90dBAM Tuner SectionFrequency Range5221620kHzSignal-to-Noise Ratio45dBUsable SensitivityLoop: 500VDistortion1kHz, 50% Mod: 0.8%Selectivity10kHz: 30dBVideo SectionVideo FormatPAL/NTSCInput Level/Impedance1Vp-p/75 ohmsOutput Level/Impedance1Vp-p/75 ohmsVideo Frequency Response(Composite

20、and S-Video)10Hz8MHz (-3dB)Video Frequency Response (Component)10Hz100MHz (-3dB)GeneralPower RequirementAC 220240V/50HzPower Consumption65W idle, 540W maximum (5 channels driven) Dimensions (Max)Width440mm Height165mm Depth382mm Weight9.7 kgDepth measurement includes knobs, buttons and terminal conn

21、ections.Height measurement includes feet and chassis.All features and specifications are subject to change without notice.Harman Kardon,The Bridgeand Logic 7 are registered trademarks of Harman International Industries, Incorporated.is a trademark of Harman International Industries, Inc.*Manufacture

22、d under license from Dolby Laboratories.“Dolby,”“Pro Logic” and the Double-D symbol are trademarks of Dolby Laboratories.DTS and DTS Neo:6 are registered trademarks of DTS,Inc. 96/24 is a trademark of DTS, Inc.SA-CD is a trademark of Sony Electronics, Inc.Apple and iPod are registered trademarks of

23、Apple Computer, Inc.Cirrus is a registered trademark of Cirrus Logic Corp.*Without input anti slewing and output isolation networks.TMharman/kardonAVR 145/230 service manualPage 4 of 13545TROUBLESHOOTING GUIDESYMPTOMCAUSESOLUTIONUnit does not function when Main No AC Power Make certain AC power cord

24、 is plugged into Power Switch is pusheda live outlet Check to see whether outlet is switch-controlledDisplay lights, but no sound Intermittent input connections Make certain that all input and speaker connections or pictureare secure Mute is on Press Mute Button Volume control is down Turn up volume

25、 controlNo sound from any speaker; Amplifier is in protection mode Check speaker wire connections for shorts at receiver and light around power switch is reddue to possible shortspeaker ends Amplifier is in protection mode Contact your local Harman Kardon service centerdue to internal problemsNo sou

26、nd from surround or Incorrect surround mode Select a mode other than Stereocenter speakers Input is monaural There is no surround information from mono sources Incorrect configuration Check speaker mode configuration Stereo or Mono program material The surround decoder may not create center- or rear

27、-channel information from nonencoded programsUnit does not respond to Weak batteries in remote Change remote batteriesremote commands Wrong device selected Press the AVR selector Remote sensor is obscured Make certain front panel sensor is visible to remoteor connect an optional remote sensorIntermi

28、ttent buzzing in tuner Local interference Move unit or antenna away from computers, fluorescent lights, motors or other electrical appliancesLetters flash in the channel indicator Digital audio feed paused Resume play for DVDdisplay and digital audio stops Check that Digital Input is selectedIn addi

29、tion to the items shown above, additional information on troubleshooting possible problems with your AVR 145, or installation-related issues, maybe found in the list of Frequently Asked Questions which is located in the Product Support section of our Web site at .AVR 145 OM (New) 8/4/06 1:19 PM Page

30、 45harman/kardonAVR 145/230 service manualPage 5 of 135NODESCRIPTIONPARTS NO.Q,ty123451ACCESSORY-1BOX,OUT CARTON5613DESCRIPTIONNOCPS4A564CQXAVR145/230CPG1A820W111Q,tyPARTS NO.CPS4A565SNOW,PAD(R)411. Instruction manual assy - Accessories2. Package Drawing711SNOW,PAD(L)AVR145/230SETAVR145/230SET1FM 1

31、POL ANTCSA1A018Z11NODESCRIPTIONPARTS NO.Q,ty9101112131CPB1061YPOLY BAGCQX1A1135YMANUAL,INSTRUCTIONMANUAL ,SETUP GUIDE11BOOKLET,INFORMATIONCQE1A180Z1STAPLECPL09053ACCESSORY-2ACCESSORY-1CPB1061YPOLY BAGCSA1A027ZAM LOOP ANTENNA ASSY1CABR03P3BATTERY3COVER ASSYCGRAVR130/230ZAPOLY BAG112723AM LOOP ANTENNA

32、 ASSYBATTERY ASSY4FM 1 POLE ANT5COVER ASSY6BOOKLET,INFORMATION9MANUAL INSTRUCTION10MANUAL SETUP CODE1111CGR1A332M7H43CQE1A220ZCPS1A6761CPB1A176Z112 345CGR1A331M7H431PAD , COVERCOVER ACOVER BSHEET,FRONT COVERBAG , POLYACCESSORY-2CQXAVR145/230CQX1A1138X131IMAGE BROCHURESHQE1A273ZIMAGE BROCHURESSTAPLEP

33、OLY BAGACCESSORY-11SNOW PAD (R)3BOX ,OUT CARTON5SET4SNOW PAD (L)2ACCESSORY-26REMOCONTRANSMITTER ASSY26STAPLE88STAPLECPL09053REMOCON ASSYCARTAVR145/2301harman/kardonAVR 145/230 service manualPage 6 of 1351211. Removing the Top Cabinet Remove the Screws546DISASSEMBLY13111079133128756894321 Remove the

34、Screws2. Removing the Front Panel196347 Remove the Screws4. Removing the Main PCB12517125 Remove the Screws3. Removing the Rear PanelAVR145/23025109819765202122161543211718232411121314harman/kardonAVR 145/230 service manualPage 7 of 135AVR145 DISASSEMBLY PROCEDURE 1 TOP-CABINET (21) REMOVAL 1. Remov

35、e 13 screws (S1,S7) and then remove the Top-cabinet. 2 FRONT PANEL ASSY REMOVAL 1. Remove the Top-cabinet, referring to the previous step 1. 2. Disconnect the card cable between connector (CN72-17p) on the FIP PCB (37-1) and connector (CN72) on the Input PCB (39-1). 3. Disconnect the lead wire (BN81

36、-8P) on the FIP PCB (37-1) from connector (CN81) on the Trans PCB (40-4). 4. Disconnect the lead wire (BN22-6P) on the Phone PCB (37-5) from connector (CN22) on the Input PCB (39-1). 5. Disconnect the lead wire (BN18-5P) on the Phone PCB (37-5) from connector (CN18) on the Input PCB (39-1) 6. Discon

37、nect the lead wire (BN10-4P) on the Volume PCB (37-6) from connector (CN10) on the Input PCB (39-1) 7. Disconnect the lead wire (BN41-6P) on the Volume PCB (37-6) from connector (CN41) on the Video PCB (41) 8. Remove 1 screw (S10) and then lead wire (JW82-1P,JW83-1P) on the Phone PCB (37-5). 9 .Remo

38、ve 1screw (S10) and then lead wire (JW84-1P) on the Volume PCB (37-3). 10. Remove 10 screws (S1) and then remove the Front Panel ASSY. 3 VOLUME PCB (37-6) REMOVAL 1. Remove the Top-cabinet, referring to the previous step 1. 2. Remove the Front Panel ASSY, referring to the previous step 2. 3. Pull ou

39、t the Volume Knob ASSY. 4. Disconnect connector (CN84) on the Volume PCB (37-6) from the lead wire (BN84-5P) on the FIP PCB (37-1). 5. Remove 8 screws (S2,S14), and then remove the Volume PCB (37-6). 4 PHONE PCB (37-5) REMOVAL 1. Remove the Top-cabinet, referring to the previous step 1. 2. Remove th

40、e Front Panel ASSY, referring to the previous step 2. 3. Disconnect connector (CN85)on the Phone PCB (37-5) from the lead wire (BN85-2P) on the FIP PCB (37-1). 4. Remove 2 screws (S2) and then remove the Phone PCB (37-5). 5 POWER LED PCB (37-3) REMOVAL 1. Remove the Top-cabinet, referring to the pre

41、vious step 1. 2. Remove the Front Panel ASSY, referring to the previous step 2. 3. Disconnect connector (CN88) on the Power Led PCB (37-3) from the lead wire (BN88-4P) on the FIP PCB (37-1) . 4. Remove 2 screws (S2) and then remove the Power led PCB (37-3). 6 FIP PCB (37-1) REMOVAL 1. Remove the Top

42、-cabinet, referring to the previous step 1. 2. Remove the Front Panel ASSY, referring to the previous step 2. 3. Disconnect the lead wire (BN84-5P) on the FIP PCB (37-1) from connector (CN84) on the Volume PCB (37-6). 4. Disconnect the lead wire (BN85-2P) on the FIP PCB (37-1) from connector (CN85)

43、on the Phone PCB (37-5). 5. Disconnect the lead wire (BN88-4P) on the FIP PCB (37-1) from connector (CN88) on the Power Led PCB (37-3). 6. Disconnect the connector (CN89) on the FIP PCB (37-1) from lead wire (BN89-4P) on the Key PCB (37-2). 7. Remove 3 screws (S2) and then remove the Guide PCB (37-8

44、) & the FIP PCB (37-1). 7 KEY PCB (37-2) REMOVAL 1. Remove the Top-cabinet, referring to the previous step 1. 2. Remove the Front Panel ASSY, referring to the previous step 2. 3. Remove the FIP PCB (37-1), referring to the previous step6. 4. Remove 10 screws (S2) and then remove the Key PCB (37-2).

45、AVR145 harman/kardonharman/kardon Page 8 of 1358 TUNER MODULE (42) REMOVAL 1. Remove the Top-cabinet, referring to the previous step 1. 2. Disconnect the card cable between connector (CON1-13p) on the Tuner module (42) and connector (CN13) on Input PCB (39-1). 3. Remove 2 screws (S8) and then remove

46、 the Tuner Module (42). 9 VIDEO PCB (41) REMOVAL 1. Remove the Top-cabinet, referring to the previous step 1. 2. Disconnect the card cable between connector (BN14-13p) on the Video PCB (41) and connector (CN14) on the Input PCB (39-1). 3. Disconnect connector (CN43) on the Video PCB (41) from the le

47、ad wire (BN43-4P) on the Regulator PCB (A)(40-2). 4. Disconnect the card cable between connector (CN42) on the Video PCB (41) and connector (BN44-7p) on the I-Pod PCB (39-2). 5. Disconnect connector (CN41) on the Video PCB (41) from the lead wire (BN41-6P) on the Volume PCB (37-6). 6. Remove 6 screw

48、s (S8) and then remove the Video PCB (41). 10 I-POD PCB (39-2) REMOVAL 1. Remove the Top-cabinet, referring to the previous step 1. 2. Remove the Video PCB (41), referring to the previous step9 3. Disconnect connector (CN46) on the I-Pod PCB (39-2) from the lead wire (BN46-3P) on the Input PCB (39-1

49、). 4. Disconnect the card cable between connector (BN19-9p) on the I-Pod PCB (39-2) and connector (CN19) on the Input PCB (39-1). 5. Disconnect the card cable between connector (BN44-7p) on the I-Pod PCB (39-2) and connector (CN42) on the Video PCB (41). 6. Disconnect the card cable between connecto

50、r (CN47-7p) on the I-Pod PCB (39-2) and connector (CN47) on the RS232 PCB (37-7). 7. Remove 2 screws (S13) and then remove the I-Pod PCB (39-2). 11 RS232 PCB (37-7) REMOVAL 1. Remove the Top-cabinet, referring to the previous step 1. 2. Remove the Video PCB (41), referring to the previous step9 3. D