Denon-AVR2310CI-avr-sm1维修电路原理图.pdf

《Denon-AVR2310CI-avr-sm1维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Denon-AVR2310CI-avr-sm1维修电路原理图.pdf（169页珍藏版）》请在收音机爱好者资料库上搜索。

1、eD&M Holdings lnc.SERVICE MANUALAV SURROUND RECEIVERAV SURROUND AMPLIFIERMODELJPE3E2EKEAE1CE1KEUTAVR-2310CI? ?AVR-2310? ?AVR-890?MODELJPE3E2EKEAE1CE1KEUTAVC-2310? ?Ver. 3For purposes of improvement, specifications and design are subject to change without notice.Please use this service manual with re

2、ferring to the operating instructions without fail.Some illustrations using in this service manual are slightly different from the actual set.Please refer to theMODIFICATION NOTICE.X0415V03DM/DG0910RadioFans.CN 收音机爱 好者资料库2AVR-2310CI/2310/890, AVC-2310Please heed the points listed below during servic

3、ing and inspection.Heed the cautions!Spots requiring particular attention when servicing, suchas the cabinet, parts, chassis, etc., have cautions indicatedon labels or seals. Be sure to heed these cautions and thecautions indicated in the handling instructions.Caution concerning electric shock!(1) A

4、n AC voltage is impressed on this set, so touching in-ternal metal parts when the set is energized couldcause electric shock. Take care to avoid electric shock,by for example using an isolating transformer andgloves when servicing while the set is energized, un-plugging the power cord when replacing

5、 parts, etc.(2)There are high voltage parts inside. Handle with extracare when the set is energized.Caution concerning disassembly andassembly!Though great care is taken when manufacturing parts fromsheet metal, there may in some rare cases be burrs on theedges of parts which could cause injury if f

6、ingers aremoved across them. Use gloves to protect your hands.Only use designated parts!The sets parts have specific safety properties (fire resis-tance, voltage resistance, etc.). For replacement parts, besure to use parts which have the same properties. In par-ticular, for the important safety par

7、ts that are marked z onwiring diagrams and parts lists, be sure to use the desig-nated parts.Be sure to mount parts and arrangethe wires as they were originally!For safety reasons, some parts use tape, tubes or other in-sulating materials, and some parts are mounted away fromthe surface of printed c

8、ircuit boards. Care is also taken withthe positions of the wires inside and clamps are used tokeep wires away from heating and high voltage parts, sobe sure to set everything back as it was originally.Inspect for safety after servicing!Check that all screws, parts and wires removed or discon-nected

9、for servicing have been put back in their original po-sitions, inspect that no parts around the area that has beenserviced have been negatively affected, conduct an insu-lation check on the external metal connectors and betweenthe blades of the power plug, and otherwise check thatsafety is ensured.(

10、Insulation check procedure)Unplug the power cord from the power outlet, disconnectthe antenna, plugs, etc., and turn the power switch on. Us-ing a 500V insulation resistance tester, check that the in-sulation resistance between the terminals of the powerplug and the externally exposed metal parts (a

11、ntenna ter-minal, headphones terminal, microphone terminal, inputterminal, etc.) is 1M or greater. If it is less, the set mustbe inspected and repaired.Concerning important safetypartsMany of the electric and structural parts used in the sethave special safety properties. In most cases these prop-er

12、ties are difficult to distinguish by sight, and using re-placement parts with higher ratings (rated power andwithstand voltage) does not necessarily guarantee thatsafety performance will be preserved. Parts with safetyproperties are indicated as shown below on the wiring dia-grams and parts lists is

13、 this service manual. Be sure to re-place them with parts with the designated part number.(1) Schematic diagrams . Indicated by the z mark.(2) Parts lists . Indicated by the z mark.Using parts other than the designatedparts could result in electric shock, fires orother dangerous situations.SAFETY PR

14、ECAUTIONSThe following check should be performed for the continued protection of the customer and service technician.LEAKAGE CURRENT CHECKBefore returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassisresistance check. If the leakage current

15、exceeds 0.5 milliamps, or if the resistance from chassis to either side of thepower cord is less than 460 kohms, the unit is defective.CAUTIONCAUTIONRadioFans.CN 收音机爱 好者资料库3AVR-2310CI/2310/890, AVC-2310DIMENSION AVR-2310CI/2310, AVC-2310 model 4AVR-2310CI/2310/890, AVC-2310 AVR-890 model 5AVR-2310CI

16、/2310/890, AVC-2310WIRE ARRANGEMENTIf wire bundles are untied or moved to perform adjustment or parts replacement etc., be sure to rearrange them neatly asthey were originally bundled or placed afterward.Otherwise, incorrect arrangement can be a cause of noisegeneration.Wire arrangement viewed from

17、the topBack Panel sideFront Panel side6AVR-2310CI/2310/890, AVC-2310DISASSEMBLY Disassemble in order of the arrow of the figure of following flow. In the case of the re-assembling, assemble it in order of the reverse of the following flow. In the case of the re-assembling, observe attention of assem

18、bling it.CABINET TOP PANEL FRONT ASSYPCB HDMI ASSYRefer to DISASSEMBLY 1.PANEL FRONT ASSYRefer to DISASSEMBL 2.PCB HDMI ASSYand EXPLODED VIEWand EXPLODED VIEWPCB S/W PCB HDMI ASSY (Ref. No. of EXPLODED VIEW : B1) (Ref. No. of EXPLODED VIEW : B23)PCB FUNCTION ENCORDER (Ref. No. of EXPLODED VIEW : B2)

19、PCB FRONTPCB DIGI-CNT ASSYBRACKET HDMI (Ref. No. of EXPLODED VIEW : B3)Refer to DISASSEMBL 4.PCB DIGI-CNT ASSYRefer to DISASSEMBLY 3.BRACKET HDMIPCB H/Pand EXPLODED VIEWand EXPLODED VIEW? (Ref. No. of EXPLODED VIEW : B4)PCB DIGI-CNT ASSYBRACKET HDMI PCB V.AUX (Ref. No. of EXPLODED VIEW : B24) (Ref.

20、No. of EXPLODED VIEW : 42) (Ref. No. of EXPLODED VIEW : B5)PCB DIGI_POWER ASSYPCB FUNCTIONTUNER PACK (Ref. No. of EXPLODED VIEW : B32) (Ref. No. of EXPLODED VIEW : B6)Refer to DISASSEMBL 5.TUNER PACKPCB CNT FUNCTIONand EXPLODED VIEW (Ref. No. of EXPLODED VIEW : B7)TUNER PACKPCB ENCORDER (Ref. No. of

21、 EXPLODED VIEW : 36) (Ref. No. of EXPLODED VIEW : B8)PCB CNT ENCORDERE2/E2A/E1C model (Ref. No. of EXPLODED VIEW : B9)CHASSIS BACKPCB PRE OUT ASSYRefer to DISASSEMBLY 6.CHASSIS BACKRefer to DISASSEMBL 14.PCB PRE OUT ASSYand EXPLODED VIEWand EXPLODED VIEWTRANS MAINCHASSIS BACKPCB PRE OUT ASSYRefer to

22、 DISASSEMBLY 13.TRANS MAIN (Ref. No. of EXPLODED VIEW : 34) (Ref. No. of EXPLODED VIEW : B25)and EXPLODED VIEWPCB SPKTRANS MAIN? (Ref. No. of EXPLODED VIEW : B17) (Ref. No. of EXPLODED VIEW : 30)PCB SPK2 (Ref. No. of EXPLODED VIEW : B18)PCB SPK_CNT (Ref. No. of EXPLODED VIEW : B19)PCB SIRIUS ASSYPCB

23、 SUPPLY and PCB POWERRefer to DISASSEMBL 7.PCB SIRIUS ASSYRefer to DISASSEMBLY 12.PCB SUPPLYand EXPLODED VIEWand PCB POWER and EXPLODED VIEWPCB SIRIUS ASSYPCB SUPPLY (Ref. No. of EXPLODED VIEW : B13) (Ref. No. of EXPLODED VIEW : B26)PCB POWER (Ref. No. of EXPLODED VIEW : B14)PCB VIDEO ASSYRefer to D

24、ISASSEMBL 8.PCB VIDEO ASSYand EXPLODED VIEWPCB VIDEO ASSY (Ref. No. of EXPLODED VIEW : B23)PCB INPUT ASSYRefer to DISASSEMBL 9.PCB INPUT ASSYand EXPLODED VIEWPCB INPUT ASSY ( Ref. No. of EXPLODED VIEW : B21)PCB CNT1 (Ref. No. of EXPLODED VIEW : B30)PCB CPU ASSYRefer to DISASSEMBL 10.PCB CPU ASSYand

25、EXPLODED VIEWPCB CPU ASSY ( Ref. No. of EXPLODED VIEW : B27)PCB MAIN ASSYRefer to DISASSEMBL 11.PCB MAIN ASSYand EXPLODED VIEWPCB MAIN ASSY ( Ref. No. of EXPLODED VIEW : B20)PCB 2CH ASSY ( Ref. No. of EXPLODED VIEW : B11)PCB CNT3 ( Ref. No. of EXPLODED VIEW : B28)PCB CNT2 ( Ref. No. of EXPLODED VIEW

26、 : B29)7AVR-2310CI/2310/890, AVC-2310About the photos used for descriptions in the “DISASSEMBLY” section. The direction from which the photographs used herein were photographed is indicated at Direction of photograph: * at the left of the respective photographs. Refer to the table below for a descri

27、ption of the direction in which the photos were taken. Photographs for which no direction is indicated were taken from above the product.1. PANEL FRONT ASSY(1) Remove the screws.(2) Cut the wire clamp bands, then loose the style pin. Disconnect the connector wire.The viewpoint of each photograph(Pho

28、tografy direction)View from aboveFront sideDirection of photograph: BDirection of photograph: DDirection of photograph: CfProceeding : CABINET TOPPANEL FRONT ASSYProceeding : CABINET TOPPANEL FRONT ASSYView from bottomDirection of photograph: DStyle pin : LooseCP301cutcut8AVR-2310CI/2310/890, AVC-23

29、10(3) Loose the Cord holders, then disconnect the connector wires.(4) Disconnect the FFC Cable. (5) Remove the screws.(6) Disconnect the connector wire, then remove the screw. Cord holder : LooseCN306ACN305CN303CP503Cord holder : LooseDirection of photograph: CFFC CableCP541Direction of photograph:

30、DPlease refer to EXPLODED VIEW for the disassembly method of each P.W.B included in PANEL FRONT ASSY.9AVR-2310CI/2310/890, AVC-23102. PCB HDMI ASSY (1) Cut the wire clamp band, then disconnect the connector wires and FFC Cables.Remove the SUPPORTER, then disconnect the board to board. (2) Remove the

31、 screws.3. BRACKET HDMI(1) Cut the wire clamper, then disconnect the connector wire. Remove the screws. (2) Remove the screws.Proceeding : CABINET TOPHDMI PWB ASSYPCB HDMI ASSYBoard to boardFFC CableFFC CableCX047FFC CableSUPPORTERCX046cutDirection of photograph: AProceeding : CABINET TOPHDMI PWB AS

32、SYBRACKET HDMICP2270BRACKT HDMIcutDirection of photograph: A10AVR-2310CI/2310/890, AVC-23104. PCB DIGI-CNT ASSY (1) Disconnect the FFC cable and board to board. (2) Remove the screws.5. TUNER PACK(1) Remove the screws.Proceeding : CABINET TOPHDMI PWB ASSYDIGI-CNT PWB ASSYBRACKET HDMIFFC CableBoard t

33、o boardPCB DIGI-CNT ASSYDirection of photograph: ATUNER PACKProceeding : CABINET TOPHDMI PWB ASSYDIGI-CNT PWB ASSYBRACKET HDMIDirection of photograph: A11AVR-2310CI/2310/890, AVC-23106. CHASSIS BACK (1) Cut the wire clamp band, then loose the style pins. Disconnect the connector wires.(2) Remove the

34、 screws, then disconnect the connector wires.TUNER PACKCHASSIS BACKProceeding : CABINET TOPHDMI PWB ASSYDIGI-CNT PWB ASSYBRACKET HDMIStyle pin : LooseCP102BCN101BCN102CP501cutDirection of photograph: APCB SPK 2PCB SPKCP103CP101A12AVR-2310CI/2310/890, AVC-23107. PCB SIRIUS ASSY(1) Disconnect the boar

35、d to board. 8. PCB VIDEO ASSY(1) Disconnect the board to boards. TUNER PACKCHASSIS BACKProceeding : CABINET TOPHDMI PWB ASSYDIGI-CNT PWB ASSYPCB SIRIUS ASSYBRACKET HDMIvBoard to boardPCB DSIRIUS ASSYTUNER PACKCHASSIS BACKProceeding : CABINET TOPHDMI PWB ASSYDIGI-CNT PWB ASSYPCB SIRIUS ASSYPCB VIDEO

36、ASSYBRACKET HDMIvBoard to boardPCB VIDEO ASSY13AVR-2310CI/2310/890, AVC-23109. PCB INPUT ASSY(1) Cut the wire clamp bands. (2) Loose the Cord holder, then disconnect the connector wires and board to board.TUNER PACKCHASSIS BACKProceeding : CABINET TOPHDMI PWB ASSYDIGI-CNT PWB ASSYPCB SIRIUS ASSYPCB

37、VIDEO ASSYPCB INPUT ASSYBRACKET HDMIDirection of photograph: CcutPCB INPUT ASSYBoard to boardCord holder : LOOSECP515CN303CP70814AVR-2310CI/2310/890, AVC-231010. PCB CPU ASSY(1) Disconnect the FFC cable. (2) Disconnect the connector wires and board to board.TUNER PACKCHASSIS BACKProceeding : CABINET

38、 TOPHDMI PWB ASSYDIGI-CNT PWB ASSYPCB SIRIUS ASSYPCB VIDEO ASSYPCB INPUT ASSYPCB CPU ASSYBRACKET HDMIDirection of photograph: CFFC CablevBoard to boardCN305PCB CPU ASSY15AVR-2310CI/2310/890, AVC-231011. PCB MAIN ASSY(1) Remove the screws. (2) Disconnect the connector wires, then remove the screws.TU

39、NER PACKCHASSIS BACKProceeding : CABINET TOPHDMI PWB ASSYDIGI-CNT PWB ASSYPCB SIRIUS ASSYPCB VIDEO ASSYPCB INPUT ASSYPCB CPU ASSYPCB MAIN ASSYBRACKET HDMIDirection of photograph: CView from bottomCP2270CP541CP104CP511PCB MAIN ASSY16AVR-2310CI/2310/890, AVC-231012. PCB SUPPLY and PCB POWER (1) Discon

40、nect the connector wires, then remove the screws. (2) Cut the wire clamp bands, then disconnect the connector wires and SUPPORTER.TUNER PACKCHASSIS BACKProceeding : CABINET TOPHDMI PWB ASSYDIGI-CNT PWB ASSYPCB SUPPLY and PCB POWERBRACKET HDMIvPCB SUPPLY ASSYCP501CP503CP511CP515Direction of photograp

41、h: DSUPPORTERCP513CP512cutcutPCB POWER ASSY17AVR-2310CI/2310/890, AVC-231013. TRANS MAIN(1) Cut the wire clamp bands, then disconnect the connector wires and SUPPORTER.(2) Cut the wire clamp band, then loose the style pin. Disconnect the connector wires, then remove the screws.Proceeding : CABINET T

42、OPTRANS MAINDirection of photograph: DCP513CP301CP512cutStyle pin : LooseCP2270CN306ACP104CP501cut18AVR-2310CI/2310/890, AVC-231014. PCB PRE OUT ASSY (E2/EA/E1C model) (1) Disconnect the connector wires.(2) Remove the screws. TUNER PACKPCB PRE OUT ASSYProceeding : CABINET TOPHDMI PWB ASSYDIGI-CNT PW

43、B ASSYBRACKET HDMIvCN702CN701PCB PRE-OUT ASSYDirection of photograph: A19AVR-2310CI/2310/890, AVC-2310CAUTION IN SERVICINGInitializing AV SURROUND RECEIVERAV SURROUND RECEIVER initialization should be performed when the com, peripheral parts of com, and Digital P.W.B. are replaced.1. Switch off the

44、unit.2. With the SURROUND MODE 0 and SURROUND MODE 1 buttons pressed, press the ON/OFF button to turn the power on.3. Check that the entire display is flashing with an interval of about 1 second, and release your fingers from the 2 buttons and the microprocessor will be initialized.JIG to use for se

45、rvicingWhen you repair the printing board, you can use the following JIG (Extension cable kit). Please order to Denon Official Service Distributor in your region if necessary.00D SPK- 561 EXTENSION UNIT KIT: 1 Set00D SPK- 562 9120 CONN. JOINT KIT : 1 SetWhen you update the firmware, you can use the

46、following JIG (RS232C to internal connector conversion adapter with 8P cable kit ). Please order to Denon Official Service Distributor in your region if necessary.00DSPK-581 WRITING UNIT: 1 SetNote:If step 3 does not work, start over from step 1. All user settings will be lost and this factory setti

47、ng will be recovered when this initialization mode.So make sure to m+emorize your setting for restoring after the initialization.SURROUNDMODE 0SURROUNDMODE 1ON/OFF20AVR-2310CI/2310/890, AVC-2310SPECIAL MODE dSpecial mode setting button Press the ON/OFF button to turn on while pressing both buttons A

48、 and B at the same time.ModeButton AButton BContentscom/DSP Version display modeSTATUSDIMMERSerial No. and firmware versions such as Main, Sub, DSP are displayed in the FL manager. Errors are displayed when they occur. (Refer to 21 page.)Errors checking mode(Displaying the protection history mode)ST

49、ATUSMULTEQDisplaying the protection history(Refer to 22 page.)Initialization modeSURROUNDMODE0SURROUNDMODE1Backup data initialization is carried out.(Refer to 19 page.)Mode for switching tuner frequency stepDYNAMICEQDYNAMIC VOL-E2 model only-Select with the SOURCE 0 1 button.Change tuner frequency s

50、tep to AM9k/FM50kHz STEP or AM:10k/FM:200kHz.Mode for preventing remote control acceptanceCURSOR 0RESTOREROperations using remote control are rejected.(Mode cancellation: Turn off power and execute the same button operations as when performing setup.)Panel lock modeSURROUNDMODE0RESTOREROperations us