DBX-3BXIII-de-sm维修电路原理图.pdf

《DBX-3BXIII-de-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《DBX-3BXIII-de-sm维修电路原理图.pdf（37页珍藏版）》请在收音机爱好者资料库上搜索。

1、Model 3BX IIIThree-Band Dynamic-Range Expander with Impact Restoration SERVICE MANUAL All dbx products are manufactured under patents in the US and abroad, and on all dbx circuit designs dbx holds copyright in one or more of the following years: 1979-85. “dbx” is a registered trademark of dbx, Newto

2、n, Mass. USA. RadioFans.CN 收音机爱 好者资料库RadioFans.CN 收音机爱 好者资料库CONTENTS SPECIFICATIONS (performance minimums). 4 CIRCUIT DESCRIPTION. 1 SCHEMATIC CONVENTIONS . 1 SIGNAL PATH . 1 CONTROL-VOLTAGE (CV) PATH . 3 High-Band CV Path . 5 Low-Band CV Path . 7 Mid-Band CV Path . 7 LED DISPLAYS . 7 POWER SUPPLY a

3、nd MUTE GENERATOR . 8 ALIGNMENT PROCEDURE. 9 1. INSTRUMENTS REQUIRED . 9 2. INSPECTION and WARMUP . 9 3. POWER-SUPPLY TESTS . 9 4. CONTROL-CIRCUITRY TESTS . 9 5. VCA-SYMMETRY ADJUSTMENTS . 12 6. VCA-GAIN ADJUSTMENTS . 13 7. PERFORMANCE TESTS . 14 MODEL 3BX III PRINTED CIRCUIT BOARD ASSEMBLY. 20 MODE

4、L 3BX III MAIN ASSEMBLY. 25 SPECIFICATIONS (performance minimums) Expansion To 50% increase, maximum 12 dB upward and 20 dB downward Impact restoration To +12 dB (upward only), program-dependent Frequency response +0.5 dB 20 Hz 20 kHz, any setting Dynamic range 107 dB Total harmonic distortion (THD)

5、, no expansion 0.15% Intermodulation distortion (IMD) IHF or SMPTE 0.1%, any setting Equivalent input noise 90 dBV Attack rates Program-dependent, optimized for each bandRelease rates Linear expander program -dependent, optimized; impact restorer adjustable Maximum input and output 7 V Notes 1) Spec

6、ifications are subject to change without notice. 2) All data are for 20 Hz-20 kHz unless otherwise specified; line inputs are driven by a source impedance of 1 k-ohms and outputs are loaded by 10 k-ohms in parallel with 1000 pF; all voltages are rms (root-mean-square). 3) Dynamic range is defined as

7、 the difference between the maximum rms output signal and A-weighted noise. All noise figures are A-weighted. 4) Frequency response figures are for pink noise (or music). 5) SMPTE IMD is measured with 60 Hz and 7 kHz mixed 4:1; IHF (difference-tone) IMD is measured with 19 kHz and 20 kHz mixed 1:1;

8、output 1 V. 6) Inputs and outputs have identical polarity. 7) All dbx home products are designed to be used with components whose output impedance is less than or equal to 5 k-ohms. All units are designed to drive loads of at least 5 k-ohms in parallel with 1000 pF or less. Model 3BX III Service Man

9、ual 1 CIRCUIT DESCRIPTION SCHEMATIC CONVENTIONSThe 3BX III is a stereo unit, with two independent, identical signal paths. We will refer here to the left channel only (channel 1). Almost all of its components are identified by designations ending in L (e.g., C705L, R708L); the right channels compone

10、nt designations generally end in R; and components common to the channels generally end in numbers (e.g., C803, R801). Furthermore, components are coded according to their function within the system. The 700 series indicates the signal path or detector path (the detector section is common to both ch

11、annels, so 700 components ending in a number are in this area, while those ending in L or R are in the signal path). The 800 series indicates the power supply. Finally, the L# series indicates the LED display (e.g., RL21, UL05). SIGNAL PATHRefer to Fig. 1, a block diagram of the signal path (note th

12、at L, R suffixes are not shown and that test points TPs are for both channels, left first.) Audio input signals first are buffered by 1/2-U701L and its associated circuitry. The output of 1/2-U701L is TP1 (TP2, right channel). The signal there should be identical to that at the input except for a sm

13、all attenuation (-0.83 dB) and a roll-off at 175 kHz. Figure 1, Signal Path Model 3BX III Service Manual 2 This signal is applied to a 4.21 kHz, two-pole high-pass filter (2/2-U702L), a 210 Hz, two-pole low-pass filter (1/2-U702L), and a summing stage (2/2-U701L). The summer subtracts the outputs of

14、 the high-pass and low-pass filters from the output of the buffer, forming a band-pass filter with cut-offs at about 4.21 kHz and 210 Hz. Its roll-off will be 6 dB/octave (with some peaking at each corner frequency), while that of the high-pass or low-pass filters is 12 dB/octave. Fig. 2 shows the f

15、requency responses of these filters. Note that in their pass-bands the high-pass and low-pass filters are unity (0 dB) gain. Figure 2, Low, Mid, and high Filters, 10 dB/division The outputs of each filter are applied to the inputs of voltage-controlled amplifiers (VCAs), one each for the low (U706L)

16、, mid (U705L), and high (U704L) ranges. The gain of each VCA is independently controlled by a voltage derived from the rms-level detector for each band and the front-panel control settings. This circuitry is described in the Control-Voltage Path section, next page. The VCAs gain in decibels is propo

17、rtional to the voltage at pin 3 of each IC. Ideally the gain is 0 dB when the voltage is 0.00 mV; gain trims in the control-voltage (CV) path (see section 6 in the Alignment section) allow for a small adjustment. When pin 3 is positive, the gain in dB is negative (less than unity); when pin 3 is neg

18、ative, the gain in dB is positive (greater than unity). Also under ideal conditions, variations in pin 3 voltage will not cause any variations in the dc level at the output of a VCA, but in the 3BX III, symmetry adjustments (VR701L for the low band, VR702L for the mid, VR703L for the high) are provi

19、ded to compensate for non-ideal performance. (See the Alignment Procedure, sections 5.1 through 5.6, p.12 and following.) For a detailed explanation of this part, refer to the booklet on the VCA IC. The outputs of all three VCAs are connected to a single summer stage, 2/2-U703 (in the right channel

20、this stage is 1/2-U703). This op-amp converts the VCA-current output to a voltage signal and recombines the three bands into one. Note that the signal at pin 6 of U703 (pin 8 of the VCAs) is a current, not a voltage, which means that there wont be very much voltage at pin 6 of U703 even if the VCA i

21、s working properly. By the way, a relatively large signal at this pin (more than 10-20 mV) usually indicates a fault with U703. The output of 2/2-U703 goes through an RC-coupling stage (R731L, C776L, R732L) before connecting to the FET-based muting circuit (Q802 in the left channel, Q801 in the righ

22、t channel). These FETs are turned on for a short time whenever power is applied or turned off, to attenuate the output during power-up and power-down transients. Model 3BX III Service Manual 3 Finally, the signal passes to the switching circuitry. The switching allows the 3BX III signal path (a) to

23、come either before or after a tape deck plugged into the tape jacks of the 3BX III, (b) to receive its signal from either the tape deck or the source, and (c) to bypass the circuitry. CONTROL-VOLTAGE (CV) PATHThe 3BX III has two main purposes: first, to make loud signals louder while making soft sig

24、nals softer (upward and downward expansion), and second, to emphasize musical transients (impact restoration). The three rms detectors translate the signal level in each of the three bands into voltages (at dc or nearly so) that indicate how loud the input signal is in each of these bands. These vol

25、tages can then be processed and used to control the gain of the VCAs in the 3BX III to accomplish its two purposes. Choosing the correct time constants for the rms detectors in the first place is critical to doing this job right. Then the rms-detector signals must be processed to find the transients

26、 and produce signals suitable for increasing the musics impact. All of this detecting and processing takes place in the CV-path section of the 3BX III. Refer to Fig. 3, a block diagram of the CV path. The audio signals at the outputs of each of the signal-path filters are connected to the inputs of

27、three rms-level detectors, one for each band (U707 is the low-band detector, U708 the mid-band, U709 the high-band). For each band, the left- and right-channel signals are summed at pin 1 of the rms-detector IC. For a detailed explanation of this part, refer to the booklet on the rms-detector IC. Fi

28、gure 3, Control-Voltage Path Model 3BX III Service Manual 4 The output of these ICs (pin 7) is a dc voltage proportional to the dB signal level at the output of the filter that feeds them. TP9 is the low-band output, TP11 the mid-band, and TP13 the high-band. Table 1 shows the voltage and frequency

29、required (simultaneously at the L- and R-channel inputs) to cause (ideally) 0.00 mV at pin 7 of each rms-detector IC. The exact calibration of these voltages is not critical, since adjustments are provided in the stage following the rms detector. Input Voltage Input Frequency Rms IC Test Point Appro

30、x. Voltage 227 mV100 Hz U707 TP9 0.00 mV 88 mV 1 kHz U708 TP11 0.00 mV 69 mV 10 kHz U709 TP13 0.00 mV TABLE 1 Input levels and frequencies (both channels driven) for 0.00 mV at the rms output Along with the dc voltage is a small amount of ripple. Ideally, it will be at twice the frequency of the inp

31、ut, with no fundamental. Trim pots (VR704 in the low band. VR706 in the mid. and VR708 in the high) are provided to allow this waveform to be adjusted for perfect symmetry (see the Alignment Procedure, sections 4.1-4.3, p.9 and following). For larger input signals the rms-IC output is positive, and

32、negative for smaller input signals; it varies by 6 mV for each decibel of input-level change. The time-constant of the rms detector is dependent on the capacitance connected to pin 6. The larger the capacitor, the slower the time constant. The mid-band and high-band rms-detector ICs have small capac

33、itors connected directly between pin 6 and ground (C731 in the mid band and C741 in the high band). Also connected to pin 6 is a larger capacitor (C720, C729, C740), which connects to an op-amp. This capacitor and the circuit to which it connects form a “nonlinear capacitor” with an equivalent “valu

34、e” that changes with the signal conditions. If there are problems in verifying the expansion timing (see alignment procedure, section 7.2), check that this circuit is operating correctly by probing the output of the associated op-amp (pin 1 of U710 in the low band, of U711 in the mid band, and of U7

35、22 in the high band). The output of each op-amp should be a sinusoidal wave at twice the frequency of the input signal. See Table 2 for appropriate frequencies and levels. Input Voltage Input Frequency Op-amp Pin NumberApprox Voltage (p-p)1.0 v 50 Hz U710 1 60 mV 1.0 v 100 Hz U711 1 540 mV 1.0 v 100

36、 Hz U722 1 510 mV TABLE 2 Test conditions for the nonlinear-capacitor circuit Model 3BX III Service Manual 5 The rms-detector outputs connect to inverting buffer stages (2/2-U710, 2/2-U711, and 2/2-U722) with gains of 9. At these buffers, individual dc voltages from trim pots VR705, VR707 and VR709

37、are added to the rms-detector output voltages, and a single dc voltage from the Transition-Level control (VR710 on the front panel) is added to all three stages. The trim pots allow the outputs of the rms detectors to be calibrated to specific references (see the Alignment Procedure, sections 4.1, 4

38、.2 and 4.3), and the front-panel control allows the entire systems unity-gain point (no upward or downward expansion) to be adjusted by the customer to match the levels in his or her stereo system. TP10 is the low-band rms-buffer output, TP12 the mid-band, and TP14 the high-band. The CV path now spl

39、its in two, differently for the high- and low-bands from the mid-band. First the high band High-Band CV Path TP14 connects directly to the high-band-expansion control (VR715) on the front panel. This is one section of a three-gang pot (the other sections are labelled VR713 and VR711) which controls

40、the amount of rms-detector signal that eventually reaches pin 3 of the high-band VCA IC. Setting the pot for more expansion causes more of this signal to be allowed through. At 50% expansion, a 100 mV change at the rms output (TP13) causes a negative 50 mV change at pin 3 of the VCA (TP7). When the

41、signal at TP14 is positive, the gain of the high-band VCA will be either negative in dB or 0, depending on the position of the expansion control. When TP14 is negative, the gain will be positive or 0. The wiper of the expansion control connects to the positive input of a summer stage 2/2-U719) whose

42、 output is sent on to the VCA. TP14 also connects to the impact detector (U720 and associated circuitry), which differentiates the rms-detector-output waveform and clips off the negative-going portions of it. Its output looks like a sharp positive-going spike every time a sudden increase in input-si

43、gnal level takes place. This positive-going spike will cause the gain of the high-band VCA to increase (how much it increases depends on the setting of the Impact-Restoration control). Note that because the impact detector clips off the negative portions of the control signal, the impact restorer ne

44、ver causes negative gain (unlike the Expansion section). See Fig. 4, next page, for typical waveforms in the impact-restoration part of the CV path (note that column a is low, b is mid, c is high). The output of the impact detector connects to a time-constant circuit (1/2-U717, 2/2-U717), which stre

45、tches this spike out for a time determined by the setting of the rear Impact-Release-Rate control (VR723). The output of the time-constant circuit is directly connected to the impact-level control (VR716) on the front panel. This, too, is one section of a three-gang pot (the other sections are label

46、led VR714 and VR712), and it controls the amount of impact-control signal that reaches pin 3 of the high-band VCA. The wiper of the pot connects to the impact-disable circuit (Q703, driven from 1/2-U721), which turns off the impact-control signal at low signal levels. This prevents record-surface no

47、ise and other small signals from being raised in volume by the impact-restoration circuitry. Model 3BX III Service Manual 6 All photos: All front controls maximum; Rear trim (Impact Release Rate) centred a & b photos: c photos; 300 Hz tone-burst 316 mV rms (447 mV peak), 128 cycles on, 172 cycles of

48、f, 0.2 s/div 3 kHz tone-burst 316 mV rms (447 mV peak), 128 cycles on, 172 cycles off, 20 ms/div 4.a.14.b.14.c.1Top: Low-pass filter output, U702L, pin 1, or U702R, pin 7, 0.2 V/div; Top: Mid-band summer output, U701L, pin 7, or U701R, pin 1, 0.5 V/div; Top: High-pass filter output, U702L, pin 7, or

49、 U702R pin 1, 0.2 V/div; Bottom: Low-band rms-detector output, U707, pin 7 (TP9), 0.1 V/div. Bottom: Mid-band rms-detector output, U708, pin 7 (TP11), 50 mV/div. Bottom: High-band rms-detector output, U709, pin 7 (TP13), 0.1 V/div. 4.a.24.b.24.c.2Top: Low-band rms-buffer output, U710, pin 7 (TP10),

50、1 V/div; Top: Mid-band rms-buffer output, U711, pin 7 (TP12), 1 V/div; Top: High-band rms-buffer output, U722, pin 7 (TP14), 1 V/div; Bottom: Low-band impact-detector output, U713, pin 5, 0.2 V/div. Bottom: Mid-band impact-detector output, U714, pin 3, 0.5 V/div. Bottom: High-band impact-detector ou