AustralianMonitor-XRS10P-pwr-sm维修电路原理图.pdf

《AustralianMonitor-XRS10P-pwr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《AustralianMonitor-XRS10P-pwr-sm维修电路原理图.pdf（10页珍藏版）》请在收音机爱好者资料库上搜索。

1、 Australian Monitor 1 Clyde Street, Silverwater NSW 2128 Australia +61 2 9647 1411 .au SERVICE INFORMATION XRS10P POWERED LOUDSPEAKER CONTENTS: OPERATION MANUAL SCHEMATIC DIAGRAM RadioFans.CN 收音机爱 好者资料库XRS SERIESPOWERED AND PASSIVE LOUDSPEAKERSINSTALLATION AND OPERATION MANUALRadioFans.CN 收音机爱 好者资料库

2、1. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original factory packing.2. Read all documentation before operating your equipment. Retain all documentation for future reference.3. Follow all instruction

3、s printed on unit chassis for proper operation.4. Do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.5. Make sure power outlets conform to the power requirements listed on the back of the unit.6. Do not use the unit if the electrical power cord is f

4、rayed or broken. The power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance.7. Always operate the unit w

5、ith the AC ground wire connected to the electrical system ground. Precautions should be taken so that the means of grounding of a piece of equipment is not defeated.8. Mains voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC volta

6、ge is not covered by any warranty.9. Have gain controls on amplifi ers turned down during power-up to prevent speaker damage if there are high signal levels at the inputs.10 Power down and disconnect units from mains voltage before making connections.11. Never hold a power switch in the “ON” positio

7、n if it wont stay there itself!12. Do not use the unit near stoves, heat registers, radiators, or other heat producing devices.13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal fl ow of air around the unit, such as a

8、bed, rug, weathersheet, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky environment, the unit should be periodically “blown free” of foreign matter.14. Do not remove the cover. Removing the cover will expose you to potentially dangerous voltages. There are no

9、user serviceable parts inside.15. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.16. Do not connect the inputs / outputs of amplifi ers or consoles to any other voltage source, such as a battery, mains source, or power supply, regardless of w

10、hether the amplifi er or console is turned on or off.17. Do not run the output of any amplifi er channel back into another channels input. Do not parallel- or series-connect an amplifi er output with any other amplifi er output. Australian Monitor is not responsible for damage to loudspeakers for an

11、y reason.18. Do not ground any “hot” (red) terminal. Never connect a “hot” (red) output to ground or to another “hot” (red) output!19. Non-use periods: the power cord of equipment should be unplugged from the outlet when left unused for a long period of time.20. Service Information Equipment should

12、be serviced by qualifi ed service personnel when: A. The power supply cord or the plug has been damaged. B. Objects have fallen, or liquid has been spilled into the equipment C. The equipment has been exposed to rain D. The equipment does not appear to operate normally, or exhibits a marked change i

13、n performance E. The equipment has been dropped, or the enclosure damaged.THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUALIMPORTANT SAFETY INFORMATIONPAGE 3XRS SERIES INSTALLATION AND OPERATION MANUALBuilding on the reliability and son

14、ic quality of the very popular XR speaker series, Australian Monitor brings you the AM Pro XRS two way injection moulded speaker enclosures with more features and new aesthetic to suit both live sound reinforcement and permanent installation. From Front of House to fold back, the dance fl oor to bac

15、kground fi ll, the XRS series with both passive and powered options are designed with fl exibility and performance in mind.The AM Pro XRS range includes 8”, 10” and 12” models all with high quality compression drivers and represent a signifi cant advancement in injection moulded box design while mai

16、ntaining excellent audio quality and great value for money.AUS, EUR, USA REV A 24th Nov 2008This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the products enclosure that may be of suffi cient magnitude to constitute a risk of electric shock to person

17、s.This symbol is intended to alert the user to the presence of important operational and maintenance (servicing) instructions in the literature accompanying the appliance.To prevent electric shock do not use this (polarised) plug with an extension cord, receptacle or other outlet unless the blades c

18、an be fully inserted to prevent blade exposure. To prevent electric shock, match wide blade of plug to wide slot, fully insert.Caution:CAUTIONCAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE COVER (OR BACK), NO USER SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

19、WARNING!TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCKDO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.RISK OF ELECTRIC SHOCKDO NOT OPENINTRODUCTION 3FRONT AND REAR PASSIVE PANEL 4REAR POWERED PANEL 5SPECIFICATIONS 6INTRODUCTION AND CONTENTSPAGE 4XRS SERIES INSTALLATION AND OPERATION MANUALFRONT AND R

20、EAR PANEL PASSIVE VERSION1 High Frequecy DriverHorn loaded compression driver. Directivity 90deg x 90deg. Passive crossover in the XRS8/10/12.XRS8/XRS8P 1.5”XRS10/XRS10P 1.5”XRS12/XRS12P 2”Active crossover and power amp in XRS8P/10P/12P.XRS8P 50WXRS10P 50WXRS12P 100W2 Low Frequency WooferDriver size

21、s:XRS8/XRS8P 8”XRS10/XRS10P 10”XRS12/XRS12P 12”Active crossover and power amp in XRS8P/10P/12P.XRS8P 100WXRS10P 100WXRS12P 300WNote that the XRS8 ships as a pair.1 Speaker InputThe input connector is a 4 pole speakon compatible connector. Pins 1+ and 1- are wired to the +ve and -ve respectively of t

22、he speaker. The XRS10 and XRS12 have 2 connectors. They are wired in parallel so either connector can be used as an input, the other as a loop through.Accessories:XRS8/XRS8PXR8PMA Pole mount adapterXR8UMB Universal mounting bracketXRS10/XRS10PXR10CVR Heavy duty coverAMISLSB1 Wall mount bracketsATC30

23、3 Tripod speaker standATC304 Heavy duty tripod speaker standATC305 Winch up speaker standXR10-12UB Universal bracketXRS12/XRS12PXR12CVR Heavy duty coverAMISLSB1 Wall mount bracketsATC303 Tripod speaker standATC304 Heavy duty tripod speaker standATC305 Winch up speaker standXR10-12UB Universal bracke

24、t112XRS8 shown herePAGE 5XRS SERIES INSTALLATION AND OPERATION MANUALREAR PANEL POWERED VERSION1513 141011127892465311 MIC INThis is a balanced XLR microphone input.2 Mic SIGNALThis is a green LED signal present indicator for the Mic input. It indicates signal present on the input and is not affecte

25、d by the level control.3 LINE INThis is a balanced XLR line level input.4 Line SIGNALThis is a green LED signal present indicator for the Line input. It indicates signal present on the input and is not affected by the level control.5 LINE OUTThe LINE OUT is on an XLR connector. This output can be co

26、nnected to the LINE IN on another XRS Powered speaker to expand the system.6 Output CLIPThis is a red LED clip indicator for the mixed mic and line audio signal. Some fl ashing of red is acceptable on program transients. Continuous fl ashing of red could be placing undue stress on the speaker and wi

27、ll sound distorted. Turn down the input level until the clip LED is no longer lit.7 Mic LEVELThis controls the level of the MIC input (1).8 Mic BASSThis is the bass control for the MIC input (1). There is 12dB of cut and boost at 100Hz. This EQ is the shelving type.9 Mic TREBLEThis is the treble con

28、trol for the MIC input (1). There is 10dB of cut and boost at 10kHz. This EQ is the shelving type.10 Line LEVELThis controls the level of the LINE input. (3)11 Line BASSThis is the bass control for the LINE input (3). There is 12dB of cut and boost at 100Hz. This EQ is the shelving type.12 Line TREB

29、LEThis is the treble control for the LINE input (3). There is 10dB of cut and boost at 10kHz. This EQ is the shelving type.13 Power SwitchThis switch turns the power on or off to the unit.14 IEC Mains Input SocketThis is a standard IEC 3 pin socket. It accepts a standard IEC mains cable, (provided).

30、 The fuse draw contains the mains fuse and a spare.The mains fuse is a time lag (slow blow) HRC 20mm x 5mm ceramic or glass type fuse. XRS8P XRS10P XRS12P 2.5A 2.5A 5.0A IMPORTANT: Always replace the fuse with one of the same value and type. NOTE: Always disconnect power to the amplifi er before rep

31、lacing fuses.15 Voltage Select SwitchThis switch is used to select the mains voltage for your region. Select either 230V or 115V. IMPORTANT: Disconnect power to the amplifi er before operating this switch. IMPORTANT: Make sure this setting is correct before connecting the unit to the mains.PAGE 6XRS

32、 SERIES INSTALLATION AND OPERATION MANUALSPECIFICATIONS XRS8P XRS10P XRS12PDrivers 1 x 8” woofer 1 x 10” woofer 1 x 12” woofer 1 x 1.5” HF driver 1 x 1.5” HF driver 1 x 2” HF driverFrequency Response(-3dB) 65Hz-18kHz 55Hz-18kHz 50Hz-18kHzFrequency Response(-10dB) 55Hz-18kHz 50Hz-18kHz 40Hz-20kHzPeak

33、 Sound Level(dB 1m) 118dB 121dB 125dBTone controls Bass control 100Hz 12dB 12dB 12dBTreble control 10kHz 10dB 10dB 10dBOutput Power 100W(low) + 50W(high) 100W(low) + 50W(high) 300W(low) + 100W(high)Distortion (THD) Line 0.02% 0.02% 0.02%Microphone 0.04% 0.04% 0.04%Tweeter Dispersion(HxV) 90 x 90 90

34、x 90 90 x 90Input Impedance Line 20kOhm 20kOhm 20kOhmMicrophone 10kOhm 10kOhm 10kOhmConnectors XLR 3 XLR 3 XLR 3Power Supply AC 115V/230V, 50/60Hz AC 115V/230V, 50/60Hz AC 115/230V, 50/60HzDimensions(WxDxH) 277 x 265 x 407mm 325 x 308 x 478mm 415 x 391 x 600mmPacking Dimensions(WxDxH) 355 x 325 x 47

35、0mm 375 x 355 x 535mm 465 x 435 x 680mmNet Weight 8.6kg 10.5kg 23kgGross Weight 10.1kg 11.8kg 25.2kgPAGE 7XRS SERIES INSTALLATION AND OPERATION MANUALSPECIFICATIONS XRS8 XRS10 XRS12Drivers 1 x 8” woofer 1 x 10” woofer 1 x 12” woofer 1 x 1.5” HF driver 1 x 1.5” HF driver 1 x 2” HF driverFrequency Res

36、ponse(-3dB) 65Hz-18kHz 55Hz-18kHz 50Hz-18kHzFrequency Response(-10dB) 60Hz-20kHz 50Hz-20kHz 40Hz-20kHzSensitivity(dB 1W 1m) 92 dB 95 dB 97 dBImpedance 8 Ohm 8 Ohm 8 OhmRecommended Max Power(Wrms) 100 W 250 W 300 WMax Sound Level(dB 1m) 118dB 125dB 128dBDispersion(HxV) 90 x 90 90 x 90 90 x 90Harmonic

37、 Distortion 1% 1% 1%Speakon compatible connectors 1 2 2Dimensions(WxDxH) 277 x 257 x 400mm 321 x 321 x 464mm 415 x 382 x 620mmPacking Dimensions(WxDxH) 595 x 310 x 460mm 375 x 355 x 535mm 465 x 435 x 680mmNet Weight 6.5kg 10kg 18kgGross Weight 15kg (pair) 12kg 20kgSYDNEY(NSW SALES)1 Clyde StreetSilv

38、erwaterNSW 2128Private Bag 149Silverwater NSW 1811Phone: (02) 9647 1411Fax: (02) 9648 3698Email:.auCANBERRA(ACT SALES)1st Floor, Campion StreetDeakin ACT 2600PO Box 109Deakin West ACT 2600Phone: (02) 6260 4544Fax: (02) 6260 4744Email: .auMELBOURNE(VIC & TAS SALES)22/277Middleborough RoadBox Hill VIC

39、 3128PO Box 151 BlackburnSouth VIC 3130Phone: (03) 9890 7477Fax: (03) 9890 7977Email:.auBRISBANE(QLD SALES)42 Commercial RoadFortitude ValleyQLD 4006PO Box 2578 FortitudeValley BC QLD 4006Phone: (07) 3852 1312Fax: (07) 3252 1237Email:.auADELAIDE(SA & NT SALES)31 Walsh StreetThebartonSA 5031PO Box 15

40、7Hindmarsh SA 5007Phone: (08) 8352 4444Fax: (08) 8352 4488Email:.auPERTH(WA SALES)3/11 Howe StreetOsborne Park WA 6017PO Box 1281Osborne Park BCWA 6916Phone: (08) 9204 0200Fax: (08) 9244 3783Email:.auAUCKLAND(NZ SALES)9C Piermark Drive Albany 0752New ZealandPO Box 300-512Albany 0752Phone: (09) 415 9

41、426Fax: (09) 415 9864Email:nzhillssvl.co.nzAUSTRALIA AND NEW ZEALAND.auEUROPE / ASIA / MIDDLE EAST.auINTERNATIONAL SALES1 Clyde Street Silverwater NSW 2128 AustraliaPrivate Bag 149 Silverwater NSW 1811Phone: + 61 2 9647 1411Fax: + 61 2 9748 2537Email: .au12345678ABCD87654321DCBAR330KR430KD11N4148D31

42、N4148D21N4148D41N4148+15V+15V-15V-15VC522PC622PC710U/25V-NPC110U/25V-NPC310U/25V-NPR1510KC1522P+15V-15VCV8100U/50VR930KR1030KD51N4148D71N4148D61N4148D81N4148+15V+15V-15V-15VC1222PC1322PC1410U/25V-NPC810U/25V-NPC1010U/25V-NP231IC2AJRC4560657IC1BJRC4560231IC1AJRC4560R1560R2560R710KR810KC947PR1647R1747

43、C1610U/25V-NPC1710U/25V-NP123CON15044123CON25044123CON35040RP1-1RP2-184IC3CJRC456084IC1CJRC4560CV1104CV2104CV5104CV610484IC2CJRC4560CV3104CV4104R1410KR1310KRP1-3RP2-3C247PR2210KOPT1LCR0202C2222P231IC3AJRC4560R27100K+15VR23100KR26100R253K3R242K2-15VLED3REDIN2Q22N5401Q12N5551C1910U/25V-NPR1810KC1810U/

44、25V-NPR1910KIN1657IC2BJRC4560C2010U/25V-NPR2110K657IC3BJRC4560R2010K12345CT015P*100MM(2.5MM)-15V+15V-15VGNDSIN-OUTLIMITSIN-OUTLIMIT12345678910J1A10PIN2.54mmRP1-1IN1+15V-15V12345678910J2A10PIN2.54mmRP2-1IN2+15V-15VRP2-3RP1-3D10IN4148LED2GREER65K1R29150KR121K5C11473Q42N5551+15VD9IN4148LED1GREER55K1R28

45、150KR111K5C4473Q32N5551+15V123456CT01A6P*100MM(2.5MM)-15VGND+15VLIMITSIN-OUTC2122PR310KR110K84IC4CJRC4560231IC4AJRC4560R415KC122PR215KRP1-1R715KR815KR1010KR91MC4103C5103C3472R57K5R67K5C622PRP2B50KRP3B50KTREBLEBASS657IC4BJRC4560CV7104CV8104RP1-1OUT1+15V-15V-15V+15V12345678910J110PIN2.54mmRP1-3RP1-3RP

46、1A50KAC1V+2AC3V-4BR1KBU-806CV236800U/50VCV246800U/50VCV171000U/35VCV181000U/35VCV19220U/25VCV20220U/25VCV21104CV22104-15VGND+15VS-INLIMIT-15V+15VJP128VJP228VJP3GNDJP7HIGH+JP8HIGH-+15V-15V+35V-35VCV25470U/50VCV26470U/50VCV27104CV28104JP5LOW+JP6LOW-C15153C16153C17153C18153C4123C5392C6123C7392R268K2R27

47、6K8R288K2R296K8R915KR1015KR1115KR610KR310KC222PC81U/50VR1215KR1347KD21N4148D11N4148D31N4148R1410KR1510KR161MR171MR1810KC91U/50VR192K2R201M+15VR305K6R3147KD51N4148D41N4148D61N4148R3210KR3310KR341MR351MR3610KC20104R372K2C19104+15VD71N4148R815KCV29470U/50VCV30470U/50VCV31104CV32104R110KR5100KC110U/25V-

48、NPCV1104CV2104CV3104CV4104CV5104CV6104+15V-15VJP4EarthVin1GND2Vout3IC67815Vin2GND1Vout3IC77915STBY-GND1IN-2IN+3IN-GND4SUR5BOOTSTRAP6+VS7-VS8STAND-BY9MUTE10NC11NC12+PWVS13OUT14-PWVS15IC4TDA7294C10474C1122U/50VC1222U/50VC24 10U/50VC2510U/50VR2120KR221KR2322KR4220KR4410KR43 51KD81N4148+35V-35VSTBY-GND1

49、IN-2IN+3IN-GND4SUR5BOOTSTRAP6+VS7-VS8STAND-BY9MUTE10NC11NC12+PWVS13OUT14-PWVS15IC5TDA7294C21474C2222U/50VC2322U/50VR3820KR391K2R4022K+35V-35VR4510/1WR2410/1WC13104C26104R415K112345CZ01TJC3-5A231IC1ATL072657IC1BTL072121314IC2DTL0741098IC2CTL074567IC2BTL074321IC2ATL074121314IC3DTL0741098IC3CTL074567IC3BTL074321IC3ATL07484IC1CTL072V+4V-11IC2ETL074V+4V-11IC3ETL074Q12N5551Q22N5551R46440R47440C142.2U/100VJP9HIGH A+LIMITC3NP-10uF/25VR747KR2100KR4100K123CZ03AXP3123CZ02AXP3+15V-15VINPUT+INPUT-DZ11N4007C2710U/50VXRS10PAustralian Monitor