HarmanKardon-AVR760_230-avr-sm维修电路原理图.pdf

《HarmanKardon-AVR760_230-avr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《HarmanKardon-AVR760_230-avr-sm维修电路原理图.pdf（264页珍藏版）》请在收音机爱好者资料库上搜索。

1、harman/kardon Service Manual AVR 660/230 AVR 760/230 7 x 75W 7.1 CHANNEL A/V RECEIVER 7 x 85W 7.2 CHANNEL A/V RECEIVER Released EU2010 Harman Consumer Group, Inc. Rev 2, 07/2011 8500 Balboa Boulevard Northridge, California 91329 CONTENTS TROUBLESHOOTING GUIDE 64 PROCESSOR AND REMOTE RESET 65 EXPLODE

2、D VIEW AND PARTS 66 ALIGNMENT PROCEDURE, AMP BIAS 70 AVR 660 PARTS LIST 73 AVR 760 PARTS LIST 123 PCB DRAWINGS 177 SEMICONDUCTOR PINOUTS 195 CIRCUIT DESCRIPTION 234 BLOCK DIAGRAMS 235 WIRING DIAGRAM 238 SCHEMATIC DIAGRAMS 239-264 ESD WARNING 2 SAFETY PRECAUTIONS 3 BASIC SPECIFICATIONS 5 PACKING DRAW

3、ING AND PARTS 6 FRONT AND REAR PANELS 8 REMOTE CONTROLS 12 CONNECTIONS 15 GETTING STARTED 18 INSTALLATION 20 INITIAL SETUP 25 OPERATION 29 ADVANCED OWNERS MANUAL 36 Harman KardonAVR 660 -760, 230V Service ManualPage 1 of 264RadioFans.CN 收音机爱 好者资料库Eachprecautioninthismanualshouldbefollowedduringservi

4、cing.Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a component identified with, use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in theparts list in this ma

5、nual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptablyinsulated from the supply circuit before retuming the product to the customer.Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are

6、 calledElectrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors andsemiconductor chip components.The following techniques should be used to help reduce the incidence of component damage caused by static electricity.1. Immediat

7、ely before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge onyour body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device,which should be removed for potential shock reas

8、ons prior to applying power to the unit under test.2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, toprevent electrostatic charge build-up or exposure of the assembly.3. Use only a grounded-tip soldering iron to sol

9、der or unsolder ES devices.4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can generate electrical chargessufficient to damage ES devices.5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES

10、devices.6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacementES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.)7. Immediately bef

11、ore removing the protective material from the leads of a replacement ES device, touch the protective material to thechassis or circuit assembly into which the device will be installed.Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.8. Minimize bodily m

12、otions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing togetheror your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices.CAUTION :Harman KardonAVR 660 -760, 230V Service

13、 ManualPage 2 of 264RadioFans.CN 收音机爱 好者资料库2SAFETY PRECAUTIONSThe following check should be performed for the continuedprotection of the customer and service technician.LEAKAGE CURRENT CHECKMeasure leakage current to a known earth ground (waterpipe, conduit, etc.) by connecting a leakage current tes

14、terbetween the earth ground and all exposed metal parts of theappliance (input/output terminals, screwheads, metaloverlays, control shaft, etc.). Plug the AC line cord of theappliance directly into a 120V AC 60Hz outlet and turn theAC power switch on. Any current measured must not exceedo.5mA.ANY ME

15、ASUREMENTS NOT WITHIN THE LIMITSOUTLINED ABOVE ARE INDICATIVE OF APOTENTIAL SHOCK HAZARD AND MUST BECORRECTED BEFORE RETURNING THE APPLIANCETO THE CUSTOMER.DeviceundertestTest allexposed metalsurfacesAlso test withplug reversed(Using AC adapterplug as required)AC Leakage TestLeakagecurrenttesterRead

16、ing shouldnot be above0.5mAEarthgroundHarman KardonAVR 660 -760, 230V Service ManualPage 3 of 2645ENGLISHINTRODUCTIONPlease register your AVR 760/AVR 660 at .NOTE: Youll need the products serial number. At the same time, you can choose to be notified about new products and/or special promotions.than

17、k you for choosing a Harman Kardon product!For more than fifty years, the Harman Kardon mission has been to share a passion for music and entertainment, using leading-edge technology to achieve premium performance. Harman Kardon, Inc., invented the receiver, a single component designed to simplify h

18、ome entertainment without compromising performance. Over the years, Harman Kardon products have become easier to use, while offering more features and sounding better than ever. The AVR 760 multizone 7.2-channel digital audio/video receiver (AVR 660 is 7.1-channel) continues this tradition with some

19、 of the most advanced audio and video processing capabilities yet, and a wealth of listening and viewing options.To obtain the maximum enjoyment from your new receiver, please read this manual and refer back to it as you become more familiar with its features and their operation.If you have any ques

20、tions about this product, its installation or its operation, please contact your Harman Kardon retailer or custom installer, or visit the Web site at .Harman Kardon aVr 760/aVr 660 7.2-channel audio/Video receiverAudio SectionAVR 760 : 85 Watts x 7, seven channels driven at full power at 8 ohms, 20H

21、z 20kHz, 0.07% THD, 595 watts total. AVR 660: 75 Watts x 7, 525 watts total.High-current capability, ultrawide-bandwidth amplifier design with low negative feedbackAll-discrete amplifier circuitry Quadruple-crossover bass management with DVD-Audio bass management capabilityDual 32-bit TI DA 710 DSP

22、processors 192kHz/24-bit A/D and D/A conversion Sampling upconversion to 96kHz Dolby Volume processing Surround ModesDolby Digital EX, Dolby Digital Plus, Dolby TrueHD Dolby Pro Logic II and IIx (Movie, Music and Game), up to 96kHz Dolby Virtual Speaker Version 2 (Reference or Wide, 2-channel) Dolby

23、 Headphone Version 2, up to 96kHz DTS-HD High Resolution Audio, DTS-HD Master Audio DTS (5.1; DTS Stereo; DTS-ES 6.1 Discrete and Matrix) DTS 96/24 (DTS Stereo) DTS Neo:6 (Cinema 5-,6- or 7-channel; Music 5-, 6- or 7-channel), up to 96kHzLogic 7 (Movie, Music and Game), up to 96kHz 5- or 7-Channel S

24、tereo, up to 96kHz Surround Off (DSP or Analog Bypass) Harman KardonPage 4 of 26440TECHNICAL SPECIFICATIONSAudio SectionStereo Mode, Continuous Average Power (FTC) AVR 760: 100 Watts per channel, 20Hz20kHz, 0.07% THD, both channels driven into 8 ohms AVR 660: 85 Watts per channel, 20Hz20kHz, 0.07% T

25、HD, both channels driven into 8 ohmsSeven-Channel Surround Modes Power per Individual Channel for AVR 760/AVR 660 Front L & R channels: 85/75 Watts per channel 0.07% THD, 20Hz20kHz into 8 ohms Center channel: 85/75 Watts 0.07% THD, 20Hz20kHz into 8 ohms Surround (L & R Side, L & R Back) channels: 85

26、/75 Watts per channel 0.07% THD, 20Hz20kHz into 8 ohmsInput Sensitivity/Impedance Linear (High-Level) 200mV/47k ohmsSignal-to-Noise Ratio (IHF-A) 100dBSurround System Adjacent Channel Separation Pro Logic I/II 40dB Dolby Digital (AC-3) 55dB DTS 55dBFrequency Response 1W (+0dB, 3dB) 10Hz 130kHzHigh I

27、nstantaneous Current Capability (HCC) AVR 660 50 Amps AVR 760 60 AmpsTransient Intermodulation Distortion (TIM) UnmeasurableSlew Rate 40V/secFM Tuner Section Frequency Range 87.5108.0MHz Usable Sensitivity IHF 1.3V/13.2dBf Signal-to-Noise Ratio Mono/Stereo 70/68dB Distortion Mono/Stereo 0.2/0.3% Ste

28、reo Separation 40dB 1kHz Selectivity 400kHz, 70dB Image Rejection 80dB IF Rejection 90dBAM Tuner Section Frequency Range 5201720kHz Signal-to-Noise Ratio 45dB Usable Sensitivity Loop 500V Distortion 1kHz, 50% Mod 0.8% Selectivity 10kHz, 30dBVideo Section Television Format PAL Input Level/Impedance 1

29、Vp-p/75 ohms Output Level/Impedance 1Vp-p/75 ohms Video Frequency Response (Composite and S-Video) 10Hz8MHz (3dB) Video Frequency Response (Component Video) 10Hz100MHz (3dB) HDMI Version 1.3a with 10-bit Deep ColorGeneral Power Requirement AC 230V/50Hz Power Consumption 170W idle, 1220W maximum (7 c

30、hannels driven, both models) Stand-by consumption AVR 760: 1 Watt, AVR 660: 1 Watt Dimensions (Product) (Shipping) Width 440mm 520mm Height 165mm 280mm Depth 435mm 580mm Weight (Product) (Shipping) AVR 660 19kg (42 lb) 22.3kg (49 lb) AVR 760 20kg (44 lb) 23.3kg (51 lb)Depth measurement includes knob

31、s, buttons and terminal connections.Height measurement includes feet and chassis.Features, specifications and appearance are subject to change without notice.Please register your AVR 760/AVR 660 at .NOTE: Youll need the products serial number. At the same time, you can choose to be notified about ne

32、w products and/or special promotions.AVR 660 -760, 230V Service ManualPage 5 of 2645Harman KardonAVR 660 -760, 230V Service ManualPage 6 of 264PACKING DRAWING AVR 660 AVR 760AVR 660 / AVR 760 PACKAGE PARTS LISTSNOQ,ty1CPS1A801CUSHION , POLY L AVR75512CPP1A081ZBAG,POLY SET13CPS1A802CUSHION , POLY R A

33、VR75514CQE1A172XCARD , WARRANTY15SHEET , QUICK SETUP GUIDE AVR6601678CQX1A1395ZMANUAL , INSTRUCTION AVR655/2401910 CABLR03PBBATTERY , ALKALINE AAA 2PCS IN211 CPB1061WBAG , POLY(ENGLISH/FRANCH)112 CPG1A847WBOX , OUT CARTON AVR655/240113 CQB1A928ZLABEL , MADE IN PRC214 CQB1A907ZLABEL , BAR CODE AVR154

34、215 CPG1A849ZBOX , ACCESSORY116 CMA1A001ZAEXTENSION PIECE ASSY117 CJA2B054ZCORD , POWER(DETACHABLE/EUR)118 CPG1A851BOX , ANTENNA AVR755119 CSA1A035ZANT , AM LOOP (ANTLOOP-300)120 CSA1A018ZFM 1 POLE ANT121 CPG1A852BOX , ZONE2122 CARTAVR755Z2ZONE 2 REMOCON TRANSMITTER ASSY123 CPG1A853BOX , MIC AVR7551

35、24CJXAVR7550HDMICROMICRO PHONE ASSY125 CARTAVR760UREMOCON TRANSMITTER ASSY (AVR760/AVR660)126 CXZBRIDGE2354BRIDGE2 ASSY1NOQ,ty1CPS1A801CUSHION , POLY L AVR75512CPP1A081ZBAG,POLY SET13CPS1A802CUSHION , POLY R AVR75514CQE1A172XCARD , WARRANTY15SHEET , QUICK SETUP GUIDE AVR7601678CQX1A1393ZMANUAL , INS

36、TRUCTION AVR755/2401910 CABLR03PBBATTERY , ALKALINE AAA 2PCS IN211 CPB1061WBAG , POLY(ENGLISH/FRANCH)112 CPG1A847YBOX , OUT CARTON AVR755/240113 CQB1A928ZLABEL , MADE IN PRC214 CQB1A907ZLABEL , BAR CODE AVR154215 CPG1A849ZBOX , ACCESSORY116 CMA1A001ZAEXTENSION PIECE ASSY117 CJA2B054ZCORD , POWER(DET

37、ACHABLE/EUR)118 CPG1A851BOX , ANTENNA AVR755119 CSA1A035ZANT , AM LOOP (ANTLOOP-300)120 CSA1A018ZFM 1 POLE ANT121 CPG1A852BOX , ZONE2122 CARTAVR755Z2ZONE 2 REMOCON TRANSMITTER ASSY123 CPG1A853BOX , MIC AVR755124CJXAVR7550HDMICROMICRO PHONE ASSY125 CARTAVR760UREMOCON TRANSMITTER ASSY (AVR760/AVR660)1

38、26 CXZBRIDGE2354BRIDGE2 ASSY1AVR760AVR660Harman KardonAVR 660 -760, 230V Service ManualPage 7 of 2647USBENGLISHFRONT-PANEL CONTROLSPower indicatorStandby/On SwitchInfo SettingsMain Power SwitchAVR SettingsResolutionVideo ModesSource ListOKUSB PortDigital Audio Inputs (Optical and Coaxial Front)Video

39、 Inputs (S- and Composite Front)EzSet/EQ II Microphone InputBack/ExitAudio EffectsSurround ModesMenuAnalog Audio Front InputsHeadphone JackKLM NNavigationRemote IR SensorMessage DisplayVolumePower Indicator: This LED has three possible modes: Main Power Off : When the AVR is unplugged or the Main Po

40、wer Switch is off, this LED is off. Standby : Amber indicates that the AVR is ready to be turned on.On : When the AVR is turned on, this LED turns white.NOTE: If the PROTECT message ever appears, turn off the AVR and unplug it. Check all speaker wires for a possible short. If none is found, bring th

41、e unit to an authorized Harman Kardon service center for inspection and repair before using it again.Standby/On Switch: This electrical switch turns the receiver on, or places it in Standby mode for quick turn-on.Front-Panel Door (not shown): Most of the controls and connectors described below are h

42、idden behind this door. To open it, gently grab the right or left edge of the door and pull it forward and down.Main Power Switch: This mechanical switch turns the power supply on or off. It is usually left on, and cannot be turned on or off using the remote control.AVR Settings Button: Press this b

43、utton to access the AVRs main menu.Info Settings Button: Press this button to directly access the AVRs Source Info submenu, which contains the settings for the current source.Resolution: Press this button to access the AVRs video output resolution setting: 480i, 480p, 576i, 720p, 1080i or 1080p.IMPO

44、RTANT NOTE: If the AVRs video output resolution is set higher than the capabilities of the actual connection, you will not see a picture. If the best available video connection from the AVR to the TV is either composite or S-video, press this button and change the resolution to 576i.Audio Effects: P

45、ress this button to directly access the Audio Effects submenu, which allows adjustment of the tone and other audio controls. See the Initial Setup section for more information.Video Modes: Press this button for direct access to the Video Modes submenu, which contains settings that may be used to imp

46、rove the picture, if necessary, after you have adjusted the picture settings using the video display or TV.Surround Modes: Press this button to select a surround sound (e.g., multichannel) mode. The Surround Modes menu will appear on screen, and the menu line will appear in the front-panel display.

47、See the Advanced Functions section for more information on surround modes. Source List: Press this button to select a source device, which is a component where a playback signal originates, e.g., DVD.Menu Button: Press to display the menus for the tuner, the USB device, The Bridge II, the Network or

48、 Internet Radio, when any of those sources is in use.Back/Exit: Press this button to return to the previous menu, or to exit the menu system.Harman KardonPage 8 of 2648FRONT-PANEL CONTROLSKLM N Navigation: These buttons are used to navigate the AVRs menus, including the menus for the tuner, the USB

49、device, The Bridge II, the Network and Internet Radio.OK: Press this button to select the currently highlighted item.Headphone Jack: Plug a 1/4 stereo headphone plug into this jack for private listening. USB Port: Connect a USB flash drive, to play audio files in the MP3 or WMA format or still image

50、s in the JPEG format. DO NOT connect a PC, keyboards, pointing devices or other peripheral products to the AVR 760/AVR 660. Do not connect an iPod here; use The Bridge II instead. Do not connect a USB hub or multi-card device.Digital Audio, Video and Analog Audio Front Inputs: Connect a source compo