HarmanKardon-ServicingDSP维修电路原理图.pdf

《HarmanKardon-ServicingDSP维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《HarmanKardon-ServicingDSP维修电路原理图.pdf（17页珍藏版）》请在收音机爱好者资料库上搜索。

1、 Servicing DSP By Andy Andersen harman consumer group SERVICE CENTER TRAINING GUIDE RadioFans.CN 收音机爱 好者资料库 DSP technology is a very broad term covering many different functions and purposes in the world of electronics. The basic function of DSP is to take some form of digital data and make sense ou

2、t of it for our hardware. It sounds fairly simple but its a complex and growing portion of todays advanced audio equipment. The possibilities, features, and enhancements capable with DSP may be enough to discourage anyone but the architect from understanding it. Luckily, there are enough consistenci

3、es in the DSP section of todays home audio video receivers so that we dont have to specialize in designing them in order to repair them. Our mission today is to provide the fundamentals for approaching a DSP related problem using standard troubleshooting techniques. Harman Consumer Group 250 Crosswa

4、ys Park Dr. Woodbury New York 11797Email Web RadioFans.CN 收音机爱 好者资料库 DSP Service Know what works! Tame the beast. If the unit under test turns on and stays on; Do the 6/8 channel analog test 1st! Using the 6/8 input will quickly isolate audio problems in an AVR receiver. Most audio problems are not

5、DSP related but are common Analog and power supply problems. Please review Tech Tip TIP#HKTT2004-03 Isolating audio problems in an AVR receiver Using 6/8 Direct In. Use the following procedures to help find what is working, then to locate the problem area. Equipment needed: ? 1 set of (RCA) Y adapto

6、rs. ? Function/signal generator. ? Oscilloscope. Procedure: 1) Do a factory reset of the receiver. (This may eliminate common micro processor problems.) 2) Print the block diagram from the service manual. 3) With no inputs or speakers attached to the AVR turn on the receiver and turn the volume all

7、the way down. 4) Turn unit off. 5) Hook up an oscillator to the 6/8 Direct in jacks using the Y adaptors. Adjust the oscillator to about 0db (.775Volts RMS). 6) Hook up an oscilloscope to monitor the line out jacks. Or, if there are no line out (preamp out) jacks monitor the input to the power amps

8、or the speaker outs. (AVR125, 225, 130 do not have preamp out jacks) 7) Turn the AVR on. Select 6 or 8 direct in, depending on the receiver. 8) Slowly turn the volume control up until you can easily measure the voltage at the line out jacks. ( -40 to -25db ) 9) At this point you will be able to chec

9、k and assure all output levels are the same. 10) IF THE OUTPUT LEVELS ARE NOT THE SAME STOP! Go no further. At this point you will need to use the charts to see where you are losing your signal. The chart shows the analog signal flow from the input jacks to the output jacks. 11) If the output levels

10、 are the same check the power out stage at the speaker out jacks. 12) If you find the levels at the speaker out jacks are OK, your problem will be in the DSP part of the receiver. Congratulations! You have now eliminated 90% of the electronics in the AVR and confirmed that the problem is in the DSP

11、section. Harman Consumer Group 250 Crossways Park Dr. Woodbury New York 11797Email Web Page 3 If it fails, repair the analog portion of the AVR first before proceeding with the DSP check. Preamp Out 8/6 Ch. Analog Input Master Volume Control DAC DSP ADC Analog Power Amps DSP Analog flow chart What d

12、oes work! If the Analog passes through this is what we know. 1. The Analog path is OK from the input 6/8 channel direct jacks to the preamp out or the power amps. 2. Input selector switch is OK along with the +/- 15 volt power supply and the digital control of the device. 3. DSP, analog, 6/8 selecto

13、r switch is OK. 4. Master Volume control is OK. 5. Power amps, and Op Amps are OK. 6. The main micro and sub micros along with the front panel display. 7. Clock, Data, CE lines to all controlled devices in the analog path are OK 8. Main Power supply voltages including the 5 volt, +/- 15 volt and som

14、e times a 3.3/2.5 volts for the DSP and micro. Figure 1. Harman Consumer Group 250 Crossways Park Dr. Woodbury New York 11797Email Web Page 4Moving on to DSP check. Setup your bench for ease of service. Equipment needed: Dvd with Coaxial and TOSLINK (optical) S/P DIF out Dolby Digital test disk (mus

15、t include a 400Hz -20 dbfs sine wave Dolby Prologic signal, and a 30Hz -3 dbfs sine wave Dolby signal) 1 set of (RCA) Y adaptors to check analog path. 1 Toslink cable (optical) 1 Coaxial cable (or a good quality audio cable) Function/signal generator for analog path. Oscilloscope. TIP: Try not to us

16、e the speakers for DSP service. Too many wires can lead to confusion, and mistakes can easily be made. If the amp has preamp out jacks, use them! If you are still in the preliminary test setup continue to use speakers until all of the failures can be identified. Once the cover has been removed for s

17、ervicing, there is no further need to use the speaker out jacks to service the DSP board. Step 1: Do an AVR speaker test. You will need a remote control to perform this test on most AVRs. This will test of the DSP board. The speaker test tones are generated from inside the DSP chip. The first thing

18、that will happen is the microprocessor has to communicate with the DSP chip. If the DSP successfully receives the signal the DSP will return a signal to let the micro know what speaker is being tested. You will see what speaker is passing the test tone by seeing that speaker flash. If the DSP and th

19、e DACs are working, the amplitude will be the same for all channels including the subwoofer. Figure 2. Harman Consumer Group 250 Crossways Park Dr. Woodbury New York 11797Email Web Page 5Whew! That is a lot of information so far, but if successful we now know a few things: 1. The DSP chip can commun

20、icate to the micro. 2. The voltages to the dsp are probably ok. 3. If the DSP IC has an Eprom, the Eprom was successful in booting the DSP chip. (this does not mean the Eprom is ok but that it is not dead) 4. The DACs are communicating with the DSP 5. There is analog audio from the DACs through the

21、op-amps. DSP Eprom data flow Now we are looking to see audio at the preamp out jacks. This is just a go/no-go check to see if we see the signal and the amplitude is the same on all channels. TIP: Make a checklist that you can use to check all modes. If the speaker test checks out OK, we now know som

22、e more of the receiver that works. 1. The Data lines from the DSP to the DAC works. 2. The DACs work. 3. The Op Amps work. Figure 3. Page 6Harman Consumer Group 250 Crossways Park Dr. Woodbury New York 11797Email Web DAC Block of what is happening from the DSP to the audio out. FL FR SL SBR SBL SW C

23、NT SR DSP IC 4 Lines of DATA Out 4 Lines of Data L/R Clock Slave Clock Master Clock Chip Enable DSP IC +-+-+-+-+-+-+- +- +- +- +- +- +- +- +-+-AVR 520 L/R Clock Slave Clock Master Clock Chip Enable Data Lines Figure 4. Page 7Harman Consumer Group 250 Crossways Park Dr. Woodbury New York 11797Email W

24、eb Review: What we know works: CPU data to and from the DSP is OK of the DSP is OK Your voltages to the DACs are OK +/- 15 volt line to the Op Amps are OK Most of the DSP IC voltages are OK AVR 525 CS4382 AVR 520 CS4391 +5VD +V Digital Side +5VA +V Analog side +5VA +V Analog Side +3.3VL +V Logic/Dig

25、 side +3.3V +V Logic AVR 635 CS42518CQ OP-AMPS DSP ICs +5VA +V Digital Side +/- 15 volts 5V +5VD +V Analog Side 3.3V +3.3 VLB +V Logic 2.5V 1.24V Voltages of common DACs, DSP, and Op Amps What have we not checked so far? 1. Any input to the DSP. 2. The DSP clock frequency. 3. PCM or any compressed d

26、ecoding ( Dolby Digital, MPEG) 4. PCM matrix coding (Harmans Logic 7 ) 5. Analog to digital conversion 6. Coax in 7. Toslink in (optical) Figure 5. Page 8Harman Consumer Group 250 Crossways Park Dr. Woodbury New York 11797Email Web Next we need to check the input to the DSP. We have 3 types of signa

27、ls to check. 1. Analog (converted to serial data) 2. PCM (44.1khz CD) 3. Compressed digital (96khz Dolby digital, Mpeg, 44.1khz Mp3) Lets start with the digital input. Set up the bench using a DVD player for a source and test cd or cds. NOTE on Test Disk: Must have a Mono 400hz at 20db 44.1khz Mono

28、30hz at 3db 44.1khz Stereo music track 44.1khz Mono 5 tracks 400hz at 20db Dolby digital 96khz 1 track 30hz at 3db Dolby Digital 96khz 1 Track full audio all channels. Start with the CD using 400hz and 30hz Mono CD audio (PCM 44.1khz) If you get audio next check the stereo music track. If OK Now che

29、ck using Dolby Digital. First check using the tones, then the music track. If all of this passes. Then there is nothing wrong with this unit. Just kidding! This procedure should be the final check before service and done after the unit is serviced. A reminder: This is done with the cover on, and doe

30、s not need to be done by the tech that is doing the service. This procedure is a very important, and if done correctly it will reduce time spent, while improving the overall quality of service. Page 9Harman Consumer Group 250 Crossways Park Dr. Woodbury New York 11797Email Web IF DONE CORECTLY, SERV

31、ICE TIME WILL BE REDUCED AND QUALITY IMPROVED! Now the cover comes off ALL Service Procedures on the DSP starts with a quick check of all DC voltages. First possible problem: Lets start with the first thing we checked, the speaker test mode, and lets assume it has failed. We have no audio and the sp

32、eakers do not sequentially flash on the front display. Voltages were checked first and found OK (remember we checked all voltages first?). We know the CPU works, (the analog part of the receiver works and we are able to change functions) but the DSP is not responding to a command from the CPU. If yo

33、u are working with an AVR with the CPU on the front board check the cable first for loss of Data to the DSP. If your CPU is on the same board as the DSP, and if your data from the CPU is good I would suspect the DSP IC could be at fault. Note: When we are speaking of an IC being at fault we are not

34、just talking about the IC Itself being bad but any component associated with the IC. Page 10Harman Consumer Group 250 Crossways Park Dr. Woodbury New York 11797Email Web You should always look for the easy answer first! You do not need to change the engine in a car if all you need is to just add gas

35、. This also works for the DSP. For the DSP IC to work it needs lots of support from the components around it. Check all the voltages to the IC. 2.5, 3.5, 5 volts first! Then check the logic lines to the DSP chip. Start with the CPU clock to the DSP then the CPU data, CE lines. BE CAREFUL when checki

36、ng. The logic data lines have similar names to digital lines in the DSP IC. Also be aware that what one IC calls a pin, the same line could be called something different elseware. Second possible problem: Speakers sequence change on the front display but two channels are not working properly. Lets s

37、ay its FR dead and FL distorted. In diagram (4) you will note that FR and Fl come out of one DAC and the balanced out of the DAC comes out of one Op Amp. You know all the other DACs are ok so we can assume that the clock, data, CE, and L/R clock are ok. Do we have balanced audio out of the DAC? If n

38、o, check the DAC. If yes, check the Op Amps. Remember! It does not have to be the IC but could be any thing associated with the IC. Note: If all of your DACs are dead, then check what is coming out of your DSP IC. You must have Clock, Data, L/R Clock, and CE for any of the DACs to work. Page 11Harma

39、n Consumer Group 250 Crossways Park Dr. Woodbury New York 11797Email Web IC CS4252CQ is doing most of the work on the DSP board. 1. Digital in Router. 2. Input DAC for stereo audio 3. S/P DIF decoder to serial Data 4. 4 channels of digital data from DSP to 8 channels of analog audio 5. Generation of

40、 master clock. IC CS49400 only does a lot of math and has 8 channel direct input for base management. CS49400 DSP CS42528CQ Master Clock L/R Clock Slave Clock 1 Serial Data Line To DSP 7 Lines of Coax or Toslink SPDIF Input 4 Serial Data lines From DSP L/R Clock Slave Clock L/R IN Analog 4 SData lin

41、es From 8 Channel Direct ADC 8 Balanced Analog Line outsFigure 6. Page 12Harman Consumer Group 250 Crossways Park Dr. Woodbury New York 11797Email Web 7 Lines of Coax or Toslink SPDIF Input TMS320 DSP 4 Serial Data lines L/R Clock Slave Clock Master Clock L/R Clock Slave Clock Serial Data 1 Data Lin

42、e To DSP CS42518CQ L/R IN Analog 8 Balanced Analog Line outsAVR 635 DSP The TMS320 DSP IC is the fastest processor from Texas Instrument for DSP processing. Figure 7. Page 13Harman Consumer Group 250 Crossways Park Dr. Woodbury New York 11797Email Web NOTE: It is important not to just have Clock and

43、 data lines be present, but also aware of there amplitude. We are working with different voltages on different chips so there I/O logic state parameters must be considered (2.5, 3.3, 5volts). AK4114VQ SPDIF Decoder Master Clock L/R IN Analog Analog Line outs SPDIF Coax or Toslink CS493263 DSP A/D AK

44、4358VQDataDAC L/R Clock Master Clock Converter Master Clock BICK (slave clock) DataData AVR 230 DSP Block Figure 8. Page 14Harman Consumer Group 250 Crossways Park Dr. Woodbury New York 11797Email Web Lets say the speaker test was ok. Review time! What do we know that is working? 1. Data from the CP

45、U to the DSP. 2. All the output DACs and Op Amps. 3. All voltages to the DSP, DACs, and Op Amps (2.5, 3.3, 5, +/-15) 4. Master Clock and sub clocks to and from DSP Whew! Now we must check the inputs to the DSP. Start with hooking up a DVD player to ether the coax input or optical input (toslink). Us

46、e the 400hz 20db 44.1khz test tone (PCM CD audio). If we have no audio we need to check the digital path from the in inputs to the DSP. Analog to Digital Converter And Analog Input Buffer +2.5V For DC Offset Calibration Right Audio In Left Audio In Audio In S Data M Clock S Clock L/R Clock R+ R- CS5

47、361 ADC L+ L- Figure 9. Page 15Harman Consumer Group 250 Crossways Park Dr. Woodbury New York 11797Email Web Note: The Master clock frequencies are different for CDs and DVDs. If the DSP clock does not lock onto the input signal you will not get audio! Clock frequency is very important! Master Clock

48、 Frequencys in megahertz (Mhz) Using Optical 1 on DVD input using a DVD player AVR 630 AVR 230 DVD play 12.28735DVD Play 12.2873* CD play 11.28903CD Play 11.28904 Opt. Cable Pulled 24.57555Opt. Cable Pulled 5.292* Speaker Test 12.28773Analog In 12.8783 If your PCM audio was ok but no DVD audio, firs

49、t check your clock freq. If clock is ok suspect the DSP chip is NG op the Eprom is NG. Dolby Digital requires a decoder to work, and that is provided in the software cared in the DSP and the E prom. Common problems: 1. Poor Soldering. 2. Voltages NG do to A. Decupling caps B. Regulator ICs. If a bad

50、 regulator is found be aware of bad decupling caps. C. Shorted ICs 3. Strange problems? Check with Customer service 1st! In this age of electronics, not everything works like we thing it should. What you are finding could be a fault with the customers source material or there hardware. If there are