ElectroVoice-P1202-pwr-sm维修电路原理图.pdf

《ElectroVoice-P1202-pwr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《ElectroVoice-P1202-pwr-sm维修电路原理图.pdf（22页珍藏版）》请在收音机爱好者资料库上搜索。

1、 P 1201 P 1202 MODULAR PRECISION SERIESSERVICERadioFans.CN 收音机爱 好者资料库1 / 7 Technical Specifications: X1201 / P1201 Amplifier at rated conditions, 8 output load, unless otherwise specified. X1201 / P1201 Load Impedance 8 4 2 Maximum Midband Output Power THD = 1%, 1kHz 750 W 1200 W 1600 W Rated Output

2、 Power THD 0.2%, 20Hz . 20kHz 500 W 1000 W - Max. Single Channel Output Power Dynamic-Headroom, IHF-A 850 W 1450 W 1700 W Maximum RMS Voltage Swing THD = 1%, 1kHz 86 V Voltage Gain at 1kHz 33 dB Slew Rate at 1kHz 40 V/s Power Consumption at 1/8 maximum output power 4 870 W Input Sensitivity at rated

3、 output power 4, 1kHz 1.4 V THD at rated output power, MBW = 80kHz, 1kHz 0.05 % IMD-SMPTE 60Hz, 7kHz 0.08 % DIM30 3.15kHz, 15kHz 300 / 200 Signal to Noise Ratio A-weighted, non internal summing mode 106 dB Power Requirements 240V, 230V, 120V, 100 V, 50Hz . 60Hz, factory configured Protection Audio l

4、imiters, High temperature, DC, HF, Back-EMF, Peak current limiters, Inrush current limiters, Turn-on delay Cooling Front-to-rear, 3-stage-fans Safety Class I Dimensions (W x H x D), mm 483 x 132.5 x 426 Weight 17 kg Optional Input transformer NRS 90208 (121 641) Rear-rackmount 15,5“ Rear-rackmount 1

5、8“ NRS 90235 (112 733) NRS 90223 (112 701) RadioFans.CN 收音机爱 好者资料库2 / 7MEASURED DATAX1201 / P1201The measured data apply to the following appliances:Unit ModelUnit NumberMains VoltageMains FrequencyX1201112 736230V50 - 60 HzX1201240V50 - 60 HzX1201100V50 - 60 HzX1201120V50 - 60 HzP1201170 149230V50

6、60 HzP1201170 148120V50 60 HzP1201170 148100V50 60 HzMEASURED DATA: X1201 / P1201 Printed boards name and corresponding EDP numbers:Printed boards EDP numbers100V120V230V240V81344813448134481344841998419984194Printed board parts 84194 / 84199IndexAmplifier - PCB84194/1 / 84199/1Bus - PCB84194/2 / 84

7、199/2Main - PCB84194/3 / 84199/3LED - PCB84194/4 / 84199/4Testing Conditions unless differently stated:- Measuring tolerance:X= 1.5dB- Measuring frequency:f = 1kHz- Stated level values referred to:U = 775mV (0dBu)- XLR socket pin-assignment:PIN 1 = GROUND/SHIELDPIN 2 = + INPUTPIN 3 = - INPUT- Source

8、 impedance for signal-feed via XLR socket: R(Q) = 50- The printed board assembly 84194 / 84199 offers service connectors.84194/2 / 84199/2CNS1X84194/2 / 84199/2CNS2X84194/1 / 84199/1CN10 / CN11PINAssignmentPINAssignmentPINAssignment1-Vcc1LIM SwitchCN102BIAS +HOT2-15V1FLOAT. Voltage3BIAS -HOT3SYMMETR

9、Y2GNDA4FAN Voltage4+15V3GNDA5+Vcc5GNDACN116BIAS +COLD6Speaker A1LIM Switch7BIAS -COLD7Relay/Protect2-15V8TEMP Heat sink8n.c.3-15V3 / 71. Operating Voltage:U(B) = 230V 50Hz . 60Hz / U(B) = 120V 50Hz . 60Hz2. Operating Voltage Deviation Range:-30% . +10%3. Power Consumption- Driven with sine signal f

10、= 1kHzX1201 / P1201Output PowerIdling Power Consumption50 - 70 WMaximum Power Consumption (RL=4)1870 W1200 WNominal Power Consumption (RL=4)1730 W1000 WStandard Power Consumption (RL=4)590 W100 WPower Consumption at 1/8 of the Max. Output Power720 W156 WPower Consumption at 1/8 of the Max. Output Po

11、werat 10 % Mains Overvoltage870 W180 W4. Settings/Adjustments4.1. IDLING CURRENT ADJUSTMENTConnect a DC-voltmeter to the BIAS measuring points (on the printed board assembly 84194/2 / 84199/2, seeservice connectors) and adjust the idling current via the trimmers VR101 / VR301 (on the printed board a

12、ssembly84194/1 /84199/1). Adjustment has to be performed for HOT / COLD U(DC) = 7.5mV and at normal roomtemperature. If the power amplifier has previously been operated, it has to be given several hours of time forregaining normal temperature.4.2. FLOATING - SYMMETRYChecking and setting the floating

13、 voltage symmetry has to be performed immediately after adjusting the idlingcurrent.Operate the power amplifier in idling condition. Measuring between the measuring points CNS1X.1 / CNS2X.5and CNS1X.5 / CNS2X.5 with a DC-voltmeter, set the floating voltage symmetrical to GROUND via VR1 on theprinted

14、 board assembly 84194/1 (84199/1).The absolute voltage value is not critical but the symmetry of the floating voltage over GROUND.Checking the set floating voltage is possibly by use of a DC-voltmeter and measuring between on the serviceconnector between CNS2X.3 and CNS2X.5 on the printed board asse

15、mbly 84194/2 (84199/2) as well as on the pinterminal between CN10.1 and CN10.2/3 on the printed board assembly 84194/1 (84199/1).The measured DC voltage value should be 0 volts.4.3. VCA - OFFSETRhythmically open and short-circuit the pin contacts CNS2X.1 and CNS2X.2 on the printed board assembly8419

16、4/2 (84199/2). Use VR100 to adjust the power amplifier output to their minimum offset value (withoscilloscope to minimal peak value or to the audible minimum volume of the interfering pulse).5. Function Test5.1. OUTPUT Offset VoltageDC-measurement at the loudspeaker outputs with U(DC) 10mV.5.2. LIMI

17、TER5.2.1. Attenuation TestPower amplifier driven with a 1 kHz signal up to U(A) = 69 V (without load). Increase the input voltage by10dB. The LIMITER LED lights and the output voltage ascents by approximately 2dB to approximately 85 Vwhile slightly clipping. The distortion rate of the limited signal

18、 is at THD = 1.0 . 1.5%. Further increasing theinput signal up to a value of +21dBu should not result in remarkably higher clipping.5.2.2. Attack and Release TimesTest has to be performed without load resistors connected.1.) Drive the power amplifier with a burst signal (f = 1kHz, 10 cycles, rate: 0

19、.5 sec.) and U(E) = +16dBu at theinput.4 / 72.) Monitor the output signal via oscilloscope. After 3 to 4 signal periods, the limiter has controlled the highdistortion level down to a minor residual distortion (THD = 1% . 1.5%).Attack time: 3-4 msRelease time: 30-40 ms5.3 POWER-ON DELAYMake sure that

20、 the signal is present at the power amplifier input. Switch the power amplifier via the Power-ONswitch on. Approximately 2 seconds after switching the power on, the signal will be present at the output.5.4 FAN CONTROLUpon switching the power amplifiers power on, the fans will run for approximately 2

21、 seconds and stop when thepower amplifier has regained normal temperature. In idling condition (Power-ON, no signal present) the fansare switched between SLOW and OFF mode, depending on the heat sinks temperature.Removing the connector CN5 lets the fans run in FAST mode.The fan voltage is measured b

22、etween pin CNS2X.4 and pin CNS1X.4:SLOW ca. 17.5 VFASTca. 29.0 V5.5. SOAR-PROTECTION TESTDrive the power amplifier up to 69 V in 4. Parallel-connect a 1? resistor. The protection circuit reacts andcontinuously tries to re-start! The protect-LED lights. Repeat the test with a 2? resistor. The power a

23、mplifier shouldnot switch off.Caution: If the SOAR-protection does not react in case of mains undervoltage, repeat the test with parallel-connecting a 0.5 resistor instead of a 1.5.6. SHORT-CIRCUIT CURRENT-LIMITING TEST- drive each channel with a burst signal (f = 1kHz, 1-3 cycles, rate 1 sec.), wit

24、h U(E) = 0dB- connect a 1 load resistor- the short-circuit current-limiter limits the output voltage at the load resistor symmetrically(monitor via oscilloscope) to a peak voltage value of 40 V (approximately 40 A maximum Peak Output Current).5.7. DC-VOLTAGE PROTECTION TEST- feed a test signal ( f =

25、 5 - 7 Hz ) to the power amplifier without load resistor connected.- starting at an input voltage of approximately 5 Veff, the protection circuit reacts and continuously tries to re-start!The protect-LED blinks in the same frequency.- repeat the test with f = 14Hz. The power amplifier should not swi

26、tch off.5.8. HF-PROTECTION TESTCaution: Perform tests without load resistor connected to the power amplifier only.Feed a +20dBu sine burst signal f = 100kHz (40ms ON, 960ms OFF) to the power amplifier input.The protection circuit has to react. The power amplifier continuously tries to re-start.The P

27、ROTECT-LED blinks in the same frequency.Repeat the test with f = 50kHz. The power amplifier should not switch off.5.9. INDICATOR TESTFeed a 1kHz sine signal while slowly increasing it.At approximately -26dBu the SIGNAL-LED starts lighting and at approximately +8dBu the LIMIT-LED lights.5 / 76. Level

28、6.1. VOLTAGE AMPLIFICATIONUnitInputU(E)MeasuringpointU(A)U(A)GainLoadResistorTestfrequencyX1201/P1201CH. A or B+5.8dBuOUTPUT+39dBu69.2V33.2?1kHzX1201/P1201CH. A + B-0.2dBuOUTPUT+39dBu69.2V39.2?1kHz6.2. MAXIMUM INPUT LEVEL: U(E) = +21dBu7. GROUND LIFT-switchThe circuit ground (at the input or output

29、connector) is measured against the enclosure ground(contact on the ground-screw on the rear of the appliance or ground contact on the mains plug).Switch set toGROUNDED: R = 0UNGROUNDED : R = 58. Amplitude Non-Linearity- measured with a 8 load resistor connected- MBW = 80kHzTestAt nominal output powe

30、rRemarksTHD+N ( f = 1kHz )0.05%IMD-SMPTE0.08%60Hz, 7kHzDIM 300.03%3.15kHz, 15kHz9. Frequency ResponseLinear Frequency Response (mind border frequencies)Lower border frequencyUpper border frequency-3dBfu 104INPUT A&B R(Q) = 50 Only channel A operated. Remove the resistors R291 / R292 off the printed

31、board assembly 84194/2.X1201 /P1201SPEAKER OUT- 65- 54- 6733- 100 106INPUT A R(Q) = 506 / 711. Heat Sink TemperatureDC-voltages measured between CNS1X.8 and CNS2X.5 (GNDA)Heat sink temperature25C40C60C80C100C120C130C1.5 V3.0 V6.0 V9.0 V12.0 V13.0 V13.8 VThe switch-off point is at approx. 130 C. The

32、power amplifier enters Protect-Mode.12. SLOT-SpecificationThe power amplifier X1201 (P1201) is capable of providing a maximum current of 300mA for individualmodules with 15V operating voltage.- measured at 10 % mains undervoltage.Power consumption:Xi-11 / Xi-21 Input modulesApprox. 18 mAV Front modu

33、lesApprox. 70 mAI-1 Input moduleApprox. 18 mAMRx-Front modulesApprox. 70 mA13. Dimensions and WeightPower amplifierWeightDimensions in mmX1201 / P120117kg483 x 132.5 x 385.514. Input Connector Pin-Assignment - CN7 and Module Slot Connectors - CNSLACN7CNSLACNSLAPINAssignmentPINAssignmentPINAssignment

34、1-15V1a/1bn.c.9aKA1 (Module ID)2GNDA2a/2bn.c.9bKA2 (Module ID)3Sensout A3a/3bn.c.10a/10b+15V4Return A4a/4bn.c.11a/11bAMPA2 (alt. Output 1in2)5Sensin A5aKA4 (Module ID)12a/12bLIMINA (Limiter Input)6Signal A5bKA5 (Module ID)13a/13bBUSREFA7GNDA6a/6b-15V14a/14bSIGNALA1 (Signal Out)8GNDA7aGNDA15a/15bSWA1

35、 (Select)9Signal B7bKA3 (Module ID)16a/16bSIGNAL M (Signal In)10Sensin B8a/8bGNDA11Return B12Sensout B13GNDA14+15V7 / 715. Remote Control Connector Pin-Assignment CNRC / CNRC5VCNRCCNRCCNRC5VPINAssignmentPINAssignmentPINAssignment1AMPA218n.c.1GND-D2+5V19HTSNKTMP2GND-D3COLDCUR+20n.c.3POWER-ON4+5V21HOT

36、CUR- (68/)4GND-D5COLDCUR-22n.c.5GND-D6KA123HOTCUR+ (68/)6+5V7LIM-OUTA24n.c.7+5V8KA225AMPB2 (68/)8LED-STANDBY9n.c.26GND-D10KA327GND-D11POWER-ON28GND-D12KA429GND-D13STBYLED30AID5 (10/)14KA531AID415TIMER32AID316n.c.33AID217RELAYDRV34AID116. Amplifier-IDAID1:1MSBAID2:1 AID3:1 AID4:1 AID5:0LSBBin: 11110

37、Hex: 1EErsatzteilliste - Bill of Materials 170149P 1201 230V Pos. Nr. Ref. No.Best. Nr. Part No.BezeichnungDescriptionZubehrAccessories & packing material359919OWNERS MANUAL P 1201/2 owners manual 335589FUSS-GUMMI SJ 5009 SW rubber foot 300425KABEL-NETZ 2.0 M 10A power cable Europe 337053SCHUTZHLLE

38、650X800X0,08 poly bag 306482KRT. 2 HE 556X507X178carton 357751STYROPOR-EINLAGE X1201 filler, carton, foam 355742STYROPOR-PL. 500X370X20filler, carton, foam Mechanische TeileCabinet materialB0010341343BUCHSE-SPEAKON-VIERECK 4POLspeaker socket 4-pole G0010343270GLRI GBPC 3504 rectifier GBPC-P 3504 S00

39、10346720SCHALTER-NETZ ESB-99888V power switch 341382KNOPF-TASTE 20X8 SW 3.3push button black 351214GRIFF 109 MM GRAU 3HEhandle 109 mm 348415LFTER TYP FBAO8A24H DCfan dc 24V 348387KABEL-KONFEKT 10POL 0.300Mribbon cable assy 10-way 349610KABEL-KONFEKT 10POL 0.520Mribbon cable assy 10-way 356956KABEL-K

40、ONFEKT 12POL 0.320Mribbon cable assy 12-way 354999KABEL-KONFEKT 12POL 0.350Mribbon cable assy 12-way 356957KABEL-KONFEKT 4POL 0.420Mribbon cable assy 4-way 356663KABEL-KONFEKT 14POL 0.250Mribbon cable assy 14-way 359962FB.P 1201 BED front panel P 1201 359963RW.P1201/230V BEDrear panel P1201 351359DE

41、C.3HE-EV-LACK/P2-3000 LACtop cover 359917BLEND.P1201/2 LEER LACblank panel 359965BLEND.O-1 BEDpanel 0-1 359966BLEND.I-11 BEDpanel I-11 356867RKT X1201/P1201 230V mains transformer 230V 348805WI-SO PTC K155 100GRADsafety component PTC 348341FEDERLEISTE 3POL CE100-connector female 3-pole 813448PCBAR:X

42、1201/X1202 N 5input pcb assy CN01Y356660STIFTLEISTE 2X 7POL 1-connector male 7x2 pins C0003340524KO-EL 100.000MF 16V cap electrolytic 100uF/16V C0004340524KO-EL 100.000MF 16V cap electrolytic 100uF/16V C0005329021KO-KER 0.10MF 100V 20%cap ceramic 100nF C0006329021KO-KER 0.10MF 100V 20%cap ceramic 10

43、0nF C0501329021KO-KER 0.10MF 100V 20%cap ceramic 100nF C0502329021KO-KER 0.10MF 100V 20%cap ceramic 100nF C0503301543KO-KER 330.0PF 500V 10%cap ceramic 330pF C0504301543KO-KER 330.0PF 500V 10%cap ceramic 330pF C0505301543KO-KER 330.0PF 500V 10%cap ceramic 330pF C0506301543KO-KER 330.0PF 500V 10%cap

44、ceramic 330pF C0507301558KO-KER 33.0PF 100V 2%cap ceramic 33pF C0508301558KO-KER 33.0PF 100V 2%cap ceramic 33pF 1 / 8Pos. Nr. Ref. No.Best. Nr. Part No.BezeichnungDescriptionC0509301558KO-KER 33.0PF 100V 2%cap ceramic 33pF C0510301558KO-KER 33.0PF 100V 2%cap ceramic 33pF C0511346841KO-EL 47.000MF 16

45、V cap electrolytic 47uF/16V C0512346841KO-EL 47.000MF 16V cap electrolytic 47uF/16V C0513340523KO-EL 22.000MF 16V cap electrolytic 22uF/16V C0514340523KO-EL 22.000MF 16V cap electrolytic 22uF/16V C0515340523KO-EL 22.000MF 16V cap electrolytic 22uF/16V C0516340523KO-EL 22.000MF 16V cap electrolytic 2

46、2uF/16V C0517329021KO-KER 0.10MF 100V 20%cap ceramic 100nF C0518329021KO-KER 0.10MF 100V 20%cap ceramic 100nF D0501304360DIODE 1N 4007 GEGURTETdiode 1N 4002 D0502304360DIODE 1N 4007 GEGURTETdiode 1N 4002 H0001343457DICKS-NETZW. 8PIN 2%work 8x10k Ohm H0002343457DICKS-NETZW. 8PIN 2%work 8x10k Ohm I050

47、1327197IC NE 5532 P 2FACH OPIC NE 5532 N I0502327197IC NE 5532 P 2FACH OPIC NE 5532 N JS501351815BUCHSE-FL. XLR 3POL PRINTBxlr connector female 3-poleJS502351815BUCHSE-FL. XLR 3POL PRINTBxlr connector female 3-poleJS503351816STECKER-FL. XLR 3POL PRINTBxlr connector male 3-pin JS504351816STECKER-FL.

48、XLR 3POL PRINTBxlr connector male 3-pin R0515329215WI-SI 10.00 OHM 0.30W 5%safety resistor 10.0 Ohm R0516329215WI-SI 10.00 OHM 0.30W 5%safety resistor 10.0 Ohm 841948PCBAR#X 1201 power amp pcb assy CNAC1343516FL.STECKER 4.8/0.5 connector 4.8mm faston CNAC2343516FL.STECKER 4.8/0.5 connector 4.8mm fas

49、ton CNAC3343516FL.STECKER 4.8/0.5 connector 4.8mm faston CNAC4343516FL.STECKER 4.8/0.5 connector 4.8mm faston CNA00348802MESSERLST. 12POL connector male 12-pin CNA01348802MESSERLST. 12POL connector male 12-pin CNB00344975MESSERLST. 10POL connector male 10-pin CNB01344975MESSERLST. 10POL connector ma

50、le 10-pin CNGND343516FL.STECKER 4.8/0.5 connector 4.8mm faston CNL01330269FL.STECKER 6.3/0.8 connector 6.3mm faston CNL02330269FL.STECKER 6.3/0.8 connector 6.3mm faston CNNRC330269FL.STECKER 6.3/0.8 connector 6.3mm faston CNN01330269FL.STECKER 6.3/0.8 connector 6.3mm faston CNN02330269FL.STECKER 6.3