SONY SRF-M73电路原理图 .pdf
《SONY SRF-M73电路原理图 .pdf》由会员分享,可在线阅读,更多相关《SONY SRF-M73电路原理图 .pdf(15页珍藏版)》请在收音机爱好者资料库上搜索。
1、MICROFILM SERVICE MANUAL FM STEREO/AM PLL SYNTHESIZED RADIO US Model Panama Model SPECIFICATIONS SRF-M73 Ver 1.0 1999. 03 本资料由O K X I A 视听皮带资源库w w w . o k x i a . c n 提供 2 TABLE OF CONTENTS 1.SERVICING NOTES.2 2.GENERAL.3 3.DISASSEMBLY.4 4.ELECTRICAL ADJUSTMENTS.6 5.DIAGRAMS 5-1.Block Diagram .8 5-2
2、.Printed Wiring Boards. 10 5-3.Schematic Diagram . 13 5-4.IC Pin Function Description . 18 6.EXPLODED VIEWS. 19 7.ELECTRICAL PARTS LIST. 20 Forced Reset The system microprocessor can be reset in the following proce- dure. Use these procedure when the unit cannot be worked normally due to the overrun
3、ning of the microprocessor, etc. Procedure: 1.Set to radio OFF. 2.While pressing the SCAN button, press two buttons of START/ STOP and BAND simultaneously for 5 seconds. 3.The unit is reset, and display blinking “AM 12:00”. SECTION 1 SERVICING NOTES 3 SECTION 2 GENERAL This section is extracted from
4、 instruction manual. 4 CABINET (FRONT)/(REAR) ASSY KEY BOARD This set can be disassembled in the order shown below. SECTION 3 DISASSEMBLY Set Key BoardMain BoardKnob (A)Cabinet (Rear) Assy Cabinet (Front) Assy 2three screws (B1.7 8) 2two screws (B1.7 8) 1Remove the battery case lid of the arrow. 3ca
5、binet (front) assy 4cabinet (rear) assy 1three claws 2Open the key board to direction of the arrow. 1four claws Note: Follow the disassembly procedure in the numerical order given. 5 MAIN BOARD KNOB (A) Note: Check that two switch (S1, S2) is latched with two adaptors when carrying out installation.
6、 2screw (B1.7 8) 1Remove two solders. 3knob (vol) 4two claws S1 S2 5main board 2two knobs (A) 1claw 1claw 3two adaptors 6 AM IF ADJUSTMENT Adjust for a maximum reading on level meter T1450 kHz AM VCO VOLTAGE ADJUSTMENT Adjustment PartFrequency DisplayReading on Digital Voltmeter L4530 kHz (531 kHz)3
7、 0.1V Confirmation1710 kHz (1602 kHz)9 1V (8.5 1V) AM TRACKING ADJUSTMENT Adjust for a maximum reading on level meter L1580 kHz (621 kHz) CT11,490 kHz (1,395 kHz) FM VCO VOLTAGE CONFIRMATION Frequency DisplayReading on Digital Voltmeter 87.5 MHz3 0.3V 108 MHzLess than 11 1V FM TRACKING ADJUSTMENT Ad
8、just for a maximum reading on level meter L287.5 MHz CT2108 MHz ( ): Panama model SECTION 4 ELECTRICAL ADJUSTMENTS 0 dB = 1 V AM Setting: Band switch: AM FM Setting: Band switch: FM Repeat the procedures in each adjustment several times, and the tracking adjustments should be finally done by the tri
9、mmer ca- pacitors. Adjustment Location: Main Board (See page 7) FM RF signal generator 22.5 kHz frequency deviation by 400 Hz signal Output level: as low as possible + level meter 2 jack (J1) set MAIN board TP (FM IN) 32 0.01 F + digital voltmeter MAIN board TP (VT) FM Free-Run Adjustment Setting: P
10、rocedure: 1.Connect the frequency counter to TP (MPX) as shown the fig- ure below. 2.Tune the set to 98 MHz. 3.Adjust RT1 for 76 kHz reading on the frequency counter. Specification: 75.8 kHz to 76.2 kHz Adjustment Location: MAIN board (See page 7) 0.01 F MAIN board TP (FM IN) set FM RF signal genera
11、tor Carrier frequency : 98 MHz Modulation: no modultion Output level: 0.1 V (100 dB) + MAIN board TP (MPX) + 1 F frequency counter AM RF signal generator 30% amplitude modulation by 400 Hz signal Output level: as low as possible Put the lead-wire antenna close to the set. + level meter set 32 2 jack
12、 (J1) SRF-M73 7 8 9 MAIN BOARD (Component Side) Adjustment Location: MAIN BOARD (Conductor Side) L4 AM VCO Voltage Adjustment RT1 FM Free-Run Adjustment CT1 AM Tracking Adjustment L1 AM Tracking Adjustment T1 AM IF Adjustment FM Tracking Adjustment CT2 L2 TP (MPX) TP (FM IN) TP (VT) J1 SECTION 5 DIA
13、GRAMS 5-1.BLOCK DIAGRAM 18 20 1613 19 2422 FM FRONT-END FM IF AMP/ DISCRI DECODER AMP SWITCH BASS BOOST CONTROL POWER AMP DET REGULATOR 1/2 COUNTER 1/2 COUNTER AM IF AMP/ DET TUNING INDICATOR PD1 VCO PD2 AM FRONT-END 14 FM RF IN FM/AM MIX OUT CF3: US CF4, 5: PANAMA 10.7MHz CF1 10.7MHz BASS BOOST AMP
14、 IC2 SYSTEM CONTROLLER, LIQUID CRYSTAL DISPLAY DRIVER, KEY CONTROL IC101 EEPROM IC105 CF2 450kHz FM RF 26 FM DISCRI FM IF IN 6 721 5 1 2 14 13 L-CH OUT R-CH OUT 4 2729123 ST IND AM IF IN PILOT DET LPF2 12 TUNE IND 9 AFC1/AGC 15 BAND SELECT PILOT DET LPF1 PLL LPF1 PLL LPF2 VCO AM OSC FM OSC AM RF IN
15、FM/AM FRONT-END, FM/AM DET, MPX IC1 RT1 FM FREE-RUN L4 AM VCO VOLTAGE CT2, L2 FM TRACKING S1 FM SENS T1 AM IF CT1, L1 AM TRACKING L.P.F. B.P.F. BPF1 FM VCO BUFFER Q1 FM/AM BAND SELECT SWITCH Q3 COMPARATOR IC4 (1/2) LIQUID CRYSTAL DISPLAY LCD101 VOLTAGE DETECT IC102 B+ SWITCH Q104 DC/DC CONVERTER Q10
16、3, T101 B+ SWITCH Q6 AM IF BUFFER Q4, 5 LOW-PASS FILTER Q101 SIGNAL PATH : FM : AM 05 POWER AMP MUTE CONTROL RIPPLE FILTER Q2 KEY MATRIX S101 111, 113 116 KS0 KS3KR0 KR3 X101 75kHz SYSTEM CONTROLLER (IC101), EEPROM (IC105) B+ FM/AM TUNER (IC1), HEADPHONE AMP (IC3) B+ BASS BOOST AMP (IC2) B+ PLL LOW-
17、PASS FILTER CIRCUIT B+ AM IF AMP CIRCUIT B+ D105 1 2 IN1 IN2 HEADPHONE AMP IC3 2 4 IN1 IN2 OUT1 OUT2 9 7 OUT1 OUT2 LP GAIN B+VREF 5 6 7 COMPARATOR IC4 (2/2) 3 2 1 B+ CT1 D1-1 L1 AM FERRITE-ROD ANTENNA L2 FM RF (PANAMA) POWER XOUT XIN IF ON CE DET IN MT/SW REG VCC AM IF IN EO VCOL VCOH BAND CMP IN 24
18、 DATA 15 CK 14 21 CS SK 3 DI 4 DO CS 16252150 6 12 10 53 MUTE 5 BEEP 52317212019 DX LOCAL S2 MEGA BASS ON OFF D1-2D3 CT2 D2 L4 AM OSC L3 FM OSC RV1 VOL J1 (HEADPHONE) 2 + DRY BATTERY SIZE “AAA” (IEC DESIGNATION R03) 2PCS. 3V 10 136 9 COM0 COM3 31 34 SEG0 SEG14 35 49 SRF-M73 13 14 15 16 Waveforms KEY
19、 Board 1 IC101 XOUT 200 mV/DIV, 10 s/DIV 5-3.SCHEMATIC DIAGRAM See page 17 for IC Block Diagrams. 2 Q103 Base-1, Collector-2 (RADIO ON mode) 200 mV/DIV, 100 ns/DIV 3 Q103 Collector-1 (RADIO ON mode) 2 V/DIV, 100 ns/DIV 208 m Vp-p 13.3 s 616 m Vp-p 243 ns 4.9 Vp-p 243 ns Note on Schematic Diagram: Al
20、l capacitors are in F unless otherwise noted. pF: F 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in and 1/4 W or less unless otherwise specified. : internal component. C : panel designation. U : B+ Line. H : adjustment for repair. Power voltage is dc 3 V
21、and fed with regulated dc power supply from battery terminal. Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM () : AM Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal produc- tion tolerances. W
22、aveforms are taken with a oscilloscope. Voltage variations may be noted due to normal produc- tion tolerances. Circled numbers refer to waveforms. Signal path. F: FM f: AM FM FREE-RUN 21 Ref. No.Part No.DescriptionRemarkRef. No.Part No.DescriptionRemark R1341-216-097-00 RES, CHIP100K5%1/10W R1351-21
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SONY SRF-M73 电路原理图 SRF M73 电路 原理图