sony_icf-f1_service_manual 电路图 维修原理图.pdf
《sony_icf-f1_service_manual 电路图 维修原理图.pdf》由会员分享,可在线阅读,更多相关《sony_icf-f1_service_manual 电路图 维修原理图.pdf(10页珍藏版)》请在收音机爱好者资料库上搜索。
1、ICF-F1 AEP ModelSERVICE MANUAL FM/AM RADIO SPECIFICATIONS Frequency range: FM : 87.5 - 108 MHz AM : 526.5 - 1 606.5 kHz Speaker Approx. 10.0 cm (4 inches) dia., 8 Output v (earphone) jack ( 3.5 mm minijack) Power output 250 mW (at 10 % harmonic distortion) Power requirements 4.5V DC, three R14 (size
2、 C) batteries DC IN 4.5V jack accepts: Sony AC-E45HG AC power adaptor (not supplied) Dimensions Approx. 130 237 71.5 mm (w/h/d) (5 1/8 9 3/8 2 7/8 inches) incl. projecting parts and controls Mass Approx. 673.5 g (1 lb 8 oz) incl. batteries Design and specifications are subject to change without noti
3、ce. Ver 1.0 2000. 05 RadioFans.CN 2 Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing Keep the temperature of soldering iron around 270C during repairing. Do not t
4、ouch the soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering. SECTION 1 GENERAL This section is extracted from instruction manual. RadioFans.CN 3 SECTION 2 DISASSEMBLY Note :Disassemble the unit in t
5、he order as shown below. Cabinet (rear) assySetChassis assySpeaker (SP1) Vol boardMain board Note :Follow the disassembly procedure in the numerical order given. 2-1. CABINET (REAR) ASSY 5 4 Four screws (+BTP 3 12) 3 Two screws (+BTP 3 12) 1 Push the knob (Battery box). 2 Box, battery Cabinet (rear)
6、 assy 9 8 Two screws (+P 2.6 8) 7 Remove solderings Chassis assy 5 Knob (vol) 1 Knob (tune) 2 O ring (DIA 12.5)6 O ring (vol) 4 E ring 3 Spring, ring 3 Speaker (10 cm)(SP1) Claw Two claws 1 Spring, SP detent 2 2-2. CHASSIS ASSY2-3. SPEAKER (SP1) RadioFans.CN 4 2-4. VOL BOARD 7 Screw (+P2.6 8) Two cl
7、aws 4 Pointer 5 Scale, dial 6 Rack 3 Vol board 1 8 Gear (A), tuning capacitor 2 Remove solderings 2-5. MAIN BOARD ASSY 1 Remove solderings 7 Remove solderings 5 Main board 8 LED board 2 Jack board 4 Two screws (+P 2.6 8) 6 Screw (+P 2.6 8) 3 Three screws (+BTP 3 12) RadioFans.CN SECTION 3 ELECTRICAL
8、 ADJUSTMENTS 2-6. DIAL POINTER 5 6 Screw CV1 1mm Chassis Chassis 4 Scale, dial Rack Shaft (tune) 2 Rotate the Shaft (tune) in the direction of the arrow fully. 1 Install the tuning capacitor gear (A) in the direction as shown while it is aligned with CV1. Rack Rack Pointer Two claws 3 Push the rack
9、deep inside at the position of 1 mm away from the end surface of the Chassis as far as it can go. 5 Attach the pointer as follows : While aligning the hole of the pointer with the projection of the rack, engage the two claws of the pointer with the chassis. BAND : AM Signal generator Repeat the proc
10、edures in each adjustment several times for the maximum level meter indication. The frequency coverage and tracking adjustments should be finally done by the trimmer capacitors. AM SECTION FM SECTION Adjustment Location : Main board (Component side) Put the lead-wire antenna close to the set. 30% am
11、plitude modulation by 400Hz signal. Output level : as low as possible AM RF signal generator 0.01F FM RF signal generator telescopic antenna terminal 75kHz (100%) amplitude modulation by 1kHz signal. Output level : as low as possible 16 set + level meter Speaker terminal (SP1) AM IF ADJUSTMENT Adjus
12、t for a maximum reading on level meter. T1455 kHz AM TRACKING ADJUSTMENT Adjust for a maximum reading on level meter. L1600 kHz CT1-11,400 kHz FM TRACKING ADJUSTMENT Adjust for a maximum reading on level meter. L387.35 MHz CT1-2108.25 MHz AM FREQUENCY COVERAGE ADJUSTMENT Adjust for a maximum reading
13、 on level meter. L5516.5 kHz CT1-41,631.5 kHz FM FREQUENCY COVERAGE ADJUSTMENT Adjust for a maximum reading on level meter. CT1-3108.25 MHz BAND : FM Signal generator L3 CT1-2 FM TRACKING adjustment T1 AM IF adjustmnet CT1-4 AM FREQUENCY COVERAGE adjustment CT1-3 FM FREQUENCY COVERAGE adjustment L5
14、AM FREQUENCY COVERAGE adjustment CT1-1 AM TRACKING adjustment L1 AM TRACKING adjustment RadioFans.CN ICF-F1 7 8 SECTION 4 DIAGRAMS 4-1.PRINTED WIRING BOARDS Note on Printed Wiring Boards: X : parts extracted from the component side. b : Pattern from the side which enables seeing. MAIN BOARD S1 (BAND
15、) E Q1 C22 C28 C25 C27 30 C24 CF1 C21 R17 C18 C19 C17 R7 R8 CF2 CF4 16 T1 R5 CF3 C16 IC1 15 C12 C20 C26 C13 1 C14 R15 R3 CV1 L5 C4 C9 C5 L6 L3 C11 BPF1 C32 R10 Q2 E C29 R14 R16 C33 D2 D1 R9 C31 C30 1-678-312 11 (11) LED BOARD D3 (LIGHT) 1-678-315 11 (11) JACK BOARD R11 C34 1-678-314 11 (11) VOL BOAR
16、D RV1 R4 S2 1-678-313 11 (11) 16 CT1-4CT1-1 CT1-2CT1-3 CV1-2CV1-3 CV1-4CV1-1 TUNING L1 AM FERRITE ROD ANTENNA AM FM DRY BATTERY SIZE C (ICE DESIGNATION R14) 2PCS, 4.5V ANT1 FM TELESCOPIC ANTENNA A B C G F D E 1 2 4 3 5 6 7 G F DC IN 4.5V J2 J1 SP1 (SPEAKER) 1 2 3 4 5 E D C B A D5 (POWER) LIGHT D4 (P
17、OWER) POWER/VOLUME 6 7 12 A B C D E F G 345678910 RadioFans.CN ICF-F1 9 10 4-2.SCHEMATIC DIAGRAM Note on Schematic Diagram: All capacitors are in F unless otherwise noted. pF: F 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in and 1/4 W or less unless othe
18、rwise specified. f: internal component. C : panel designation. U : B+ Line. H : adjustment for repair. Voltages are dc with respect to ground under no-signal (detuned) conditions. no mark : FM () : AM Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal
19、 produc- tion tolerances. Signal path. F: FM f: AM The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. IC BLOCK DIAGRAM IC1CXA1019S 123456789101514131211 FM DISCRIMINATOR AF POWER AMPAM FEFM IF TUNING METER AM IF DET AGC FM
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- sony_icf-f1_service_manual 电路图 维修原理图 sony_icf f1_service_manual 维修 原理图