Yamaha-CDS1000-cd-sm维修电路原理图.pdf

《Yamaha-CDS1000-cd-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Yamaha-CDS1000-cd-sm维修电路原理图.pdf（57页珍藏版）》请在收音机爱好者资料库上搜索。

1、I CONTENTS TO SERVICE PERSONNEL . 23 PREVENTION OF ELECTROSTATIC DISCHARGE . 4 FRONT PANEL . 5 REAR PANELS . 57 REMOTE CONTROL PANEL . 8 SPECIFICATIONS / 参考仕様. 89 INTERNAL VIEW . 9 DISASSEMBLY PROCEDURES / 分解手順. 1016 TEST MODE / . 17 UPDATING FIRMWARE / 書込 . 1824 DISPLAY DATA . 25 IC DATA . 2628 PIN

2、 CONNECTION DIAGRAMS. 2930 BLOCK DIAGRAM. 31 PRINTED CIRCUIT BOARDS. 3240 SCHEMATIC DIAGRAMS. 4145 REPLACEMENT PARTS LIST . 4756 REMOTE CONTROL. 57 101092 SERVICE MANUAL SUPER AUDIO CD PLAYER Copyright 2008 All rights reserved. This manual is copyrighted by YAMAHA and may not be copied or redistribu

3、ted either in print or electronically without permission. P.O.Box 1, Hamamatsu, Japan 08.05 IMPORTANT NOTICE This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more spec

4、ifically YAMAHA Products, are already known and understood by the users, and have therefore not been restated. WARNING:Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components, and failure of the produc

5、t to perform as specified. For these reasons, we advise all YAMAHA product owners that any service required should be performed by an authorized YAMAHA Retailer or the appointed service representative. IMPORTANT:The presentation or sale of this manual to any individual or firm does not constitute au

6、thorization, certification or recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form. The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA

7、 are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributors Service Division. WARNING:Static discharges can de

8、stroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss). IMPORTANT:Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply powe

9、r to the unit. CD-S1000 CD-S1000 RadioFans.CN 收音机爱 好者资料库 2 CD-S1000 CD-S1000 WALL OUTLET EQUIPMENT UNDER TEST AC LEAKAGE TESTER OR EQUIVALENT INSULATING TABLE WARNING: CHEMICAL CONTENT NOTICE! This product contains chemicals known to the State of California to cause cancer, or birth defects or other

10、 reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHAT SO EVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact wi

11、th solder or components located inside the enclosure of this product, wash your hands before handling food. 1. Critical Components Information Components having special characteristics are marked s and must be replaced with parts having specifications equal to those originally installed. 2. Leakage

12、Current Measurement (For 120V Models Only) When service has been completed, it is imperative to verify that all exposed conductive surfaces are properly insulated from supply circuits. GMeter impedance should be equivalent to 1500 ohms shunted by 0.15F. GLeakage current must not exceed 0.5mA. GBe su

13、re to test for leakage with the AC plug in both polarities. 本機搭載基板付接合 部無鉛付。 無鉛種類、修理時下記 無鉛使用推奨。 Sn+Ag+Cu （錫+銀+銅） Sn+Cu （錫+銅） Sn+Zn+Bi （錫+亜鉛+） 注意： 無鉛融点温度通常鉛入比3040 程度高、合 使用。 All of the P.C.B.s installed in this unit and solder joints are soldered using the lead free solder. Among some types of lead fre

14、e solder currently available, it is recommended to use one of the following types for the repair work. Sn + Ag + Cu (tin + silver + copper) Sn + Cu (tin + copper) Sn + Zn + Bi (tin + zinc + bismuth) Caution: As the melting point temperature of the lead free solder is about 30C to 40C (50F to 70F) hi

15、gher than that of the lead solder, be sure to use a soldering iron suitable to each solder. About lead free solder / 無鉛 I TO SERVICE PERSONNEL WARNING: Laser Safety This product contains a laser beam component. This component may emit invisible, as well as visible radiation, which may cause eye dama

16、ge. To protect your eyes and skin from laser radiation, the following precautions must be used during servicing of the unit. 1) When testing and/or repairing any component within the product, keep your eyes and skin more than 30 cm away from the laser pick-up unit at all times. Do not stare at the l

17、aser beam at any time. 2) Do not attempt to readjust, disassemble or repair the laser pick-up, unless noted elsewhere in this manual. 3) CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Laser Emitting co

18、nditions: 1) When the top cover is removed, and the STANDBY/ON SW is turned to the “ON” position, the laser component will emit a beam for several seconds to detect if a disc is present. During this time (5-10 sec.) the laser may radiate through the lens of the laser pick-up unit. Do not attempt any

19、 servicing during this period! If no disc is detected, the laser will stop emitting the beam. When a disc is loaded, you will not be exposed to any laser emissions. 2) The laser power level can be adjusted with the VR on the pick-up PWB, however, this level has been set by the factory prior to shipp

20、ing from the factory. Do not adjust this laser level control unless instruction is provided elsewhere in this manual. Adjustment of this control can increase the laser emission level from the device. RadioFans.CN 收音机爱 好者资料库 3 CD-S1000 CD-S1000 CAUTION - VISIBLE AND / OR INVISIBLE LASER RADIATION WHE

21、N OPEN. AVOID EXPOSURE TO BEAM. VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRLNING NR DENNA DEL R PPNAD. STRLEN R FARLIG. VARO ! AVATTAESSA OLET ALTTIINA NKYVLLE JA / TAI NKYMTMLLE LASERSTEILYLLE. L KATSO STEESEEN. VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRLNING NR DENNA DEL R PPNAD. BETRAKTA EJ

22、STRLEN. VORSICHT ! SICHTBARE UND / ODER UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEFFNET. NICHT DEM STRAHL AUSSETZEN. ATTENTION - PADIATION VISIBLE ET / OU INVISIBLE LORSQUE LAPPAREIL EST OUVERT. EVITEZ TOUTE EXPOSITION AU FAISCEAU. CAUTION-CLASS 1M LASER RADIATION WHEN OPEN DO NOT VIEW DIRECTLY WI

23、TH OPTICAL INSTRUMENTS. Material: SA-CDSemiconductor laser (AlGaInP) CDSemiconductor laser (AlGaAs) Wavelength: SA-CD650 nm CD780 nm Warning for power supply The primary side of the power supply carries live mains voltage when the player is connected to the mains even when the player is switched off

24、 ! This primary area is not shielded so it is possible to accidentally touch copper tracks and/or components when servicing the player. Service personnel have to take precautions to prevent touching this area or components in this area. Note: The screws on the DVD mechanism may never be touched, rem

25、oved or re-adjusted. Handle the DVD mechanism with care when the unit has to be exchanged! The DVD mechanism is very sensitive for dropping or giving shocks. Laser Diode Properties Laser Output: SA-CD5 mW (max.) CD7 mW (max.) B, G models 4 CD-S1000 CD-S1000 I PREVENTION OF ELECTROSTATIC DISCHARGE So

26、me semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transis- tors and semiconductor “chip” components. The follow

27、ing techniques should be used to help reduce the incidence of compo- nent damage caused by electro static discharge (ESD). 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, ob

28、tain and wear a commercially available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil,

29、 to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static (ESD protected)” can generate electrical char

30、ge sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices

31、are packaged with leads electrically shorted together by conductive foam, aluminum foil or compa- rable conductive material). 7. Immediately before removing the protective material from the leads of a replacement ES divice, touch the protective mate- rial to the chassis or circuit assembly into whic

32、h the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as brush- ing together of your fabric clothes or lifti

33、ng of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device). Grounding for electrostatic breakdown prevention 1. Human body grounding. Use the antistatic wrist strap to discharge the static electricity from your body. 2. Work table grounding. Put a

34、conductive material (sheet) or steel sheet on the area where the optical pickup is placed and ground the sheet. Caution: The static electricity of your clothes will not be grounded through the wrist strap. So take care not to let your clothes touch the optical pickup. 1M-ohms Conductive material (sh

35、eet) or steel sheet Anti-static wrist strap 5 CD-S1000 CD-S1000 I FRONT PANEL CD-S1000 (U, C, R, T, K, A, B, G, L, J models) I REAR PANELS CD-S1000 (U, C models) CD-S1000 (R model) 6 CD-S1000 CD-S1000 CD-S1000 (T model) CD-S1000 (K model) CD-S1000 (A model) 7 CD-S1000 CD-S1000 CD-S1000 (B, G models)

36、 CD-S1000 (L model) CD-S1000 (J model) 8 CD-S1000 CD-S1000 I Audio Section / 部 Frequency Response / 周波数特性 SA-CD . 2 Hz to 50 kHz (-3 dB) CD .2 Hz to 20 kHz Total Harmonic Distortion (1 kHz) / 高調波歪率 （1 kHz） .0.002 % or less Signal to Noise Ratio / 信号対雑音比 (IHF-A Network) .113 dB or more Dynamic Range

37、/ SA-CD .105 dB or more CD .100 dB or more Output Level (1 kHz, 0 dB) / 出力 （1 kHz、0 dB） . 2.0 0.3 V I General / 総合 Power Supply / 電源電圧 U, C models .AC 120 V, 60 Hz R, L models .AC 110/120/220/230-240 V, 50/60 Hz T model.AC 220 V, 50 Hz K model.AC 220 V, 60 Hz A model.AC 240 V, 50 Hz B, G models .AC

38、230 V, 50 Hz J model . AC 100 V, 50/60 Hz Power Consumption / 消費電力 U, C, R, T, K, A, B, G, L models . 30 W J model . 25 W Off-state Power Consumption / OFF時消費電力 . 0 W Dimensions (W x H x D) / 寸法 （幅高奥行） . 435 x 137 x 440 mm (17-1/8” x 5-3/8” x 17-5/16”) Weight / 質量 . 15 kg (33 lbs. 1 oz.) Finish / 仕上

39、 Black color . U, C, R, T, K, A, B, G, L, J models Silver color . U, C, R, T, K, A, B, G, L, J models Accessories / 付属品 Remote control x 1, Battery (R6, AA, UM-3) x 2, Audio pin cable (1.5 m) x 1, Power cable (2 m) x 1 *Specifications are subject to change without notice due to product improvements.

40、 参考仕様外観予告変更。 I SPECIFICATIONS / 参考仕様 U . U.S.A. model C . Canadian model R . General model T . Chinese model K . Korean model A . Australian model B . British model G . European model L . Singapore model J. Japanese model I REMOTE CONTROL PANEL CDX5 9 CD-S1000 CD-S1000 DIMENSIONS / 寸法図 Unit: mm (inc

41、h) 単位：mm （） I INTERNAL VIEW 435 (17-1/8) 371 (14-5/8) 137 (5-3/8)440 (17-5/16) 418 (16-7/16) 362 (14-1/4) 120 (4-3/4)8 (5/16) 14 (9/16) 17 (11/16) 1 POWER TRANSFORMER 2 POWER (2) P.C.B. (R, L models) 3 POWER (1) P.C.B. 4 LOADER UNIT 5 AUDIO P.C.B. 6 DIGITAL (1) P.C.B. 7 DIGITAL (5) P.C.B. 8 POWER (3

42、) P.C.B. 9 DIGITAL (4) P.C.B. 0 DIGITAL (3) P.C.B. A DIGITAL (2) P.C.B. 23456 7 A 8 90 1 10 CD-S1000 CD-S1000 I DISASSEMBLY PROCEDURES / 分解手順 Fig. 1 (Remove parts in the order as numbered.) Disconnect the power cable from the AC outlet. 1. Removal of Panel Side L/R a. Remove 2 screws (1), coned disc spring L and washer side. (Fig. 1) b. Lift the panel side L a little, release hooks at 3 locations and then remove the panel side L. (Fig. 1) c. Remove 2 screws (2) and then remove 2 washers. (Fig. 1) d. Lift the