Technics-SADX1050-avr-sm维修电路原理图.pdf
《Technics-SADX1050-avr-sm维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《Technics-SADX1050-avr-sm维修电路原理图.pdf(84页珍藏版)》请在收音机爱好者资料库上搜索。
1、Order No. MD0104077C2 AV Control Stereo Receiver SA-DX1050 Colour (K) . Black Type E . Europe EB . Great Britain EG . Germany and Italy SPECIFICATIONS 1 RadioFans.CN 收音机爱 好者资料库 FM Tuner Section Frequency range87.5-108.0 MHz Sensitivity S/N 30 dB 1.5 V / 75 S/N 26 dB 1.3 V / 75 S/N 20 dB 1.2 V / 75 I
2、HF usable sensitivity (IHF58) 1.5 V / 75 IHF 46 dB stereo quieting sensitity 22 V / 75 Total harmonic distortion MONO0.2% STEREO0.3% S/N MONO60 dB (73 dB, IHF) STEREO58 dB (67 dB, IHF) Frequency response 20 Hz-15 kHz+1 dB, -2 dB Alternate channel selectivity 400 kHz 65 dB Capture ratio1.5 dB Image r
3、ejection at 98 MHz40 dB IF rejection at 98 MHz70 dB Spurious response rejection at 98 MHz 70 dB AM suppression50 dB Stereo separation 1 kHz40 dB Carrier leak 19 kHz-30 dB (-35 dB, IHF) 38 kHz-50 dB (-55 dB, IHF) Channel balance (250 Hz-6.3 kHz)1.5dB Limiting point 1.2 V Bandwidth IF amplifier180 kHz
4、 FM demodulator1000 kHz Antenna terminal 75 (unbalanced) AM Tuner Section Frequency range522-1611 kHz (9 kHz steps) 530-1620 kHz (10 kHz steps) Sensitivity 20 V, 330 V / m Selectivity (at 999 kHz)55 dB IF rejection (at 999 kHz)50 dB Video Section Output voltage at 1 V input (unbalanced) 10.1 Vp-p Ma
5、ximum input voltage1.5 Vp-p Input/output impedance 75 (unbalanced) Amplifier Section Power output 2 RadioFans.CN 收音机爱 好者资料库 Power output 3 (at 230V for Continental Europe) (at 240V for the United Kingdom,Australia and New Zealand) DIN 1 kHz (T.H.D. 1%) 2 x 100W (6 ) 20 Hz-20 kHz continuous power out
6、put both channels driven 2 x 80W (6 ) Total harmonic distortion rated power at 20 Hz-20 kHz 0.09% (6 ) half power at 1 kHz 0.03% (6 ) Power output at 1 kHz each channel driven DIN 1kHz (T.H.D.1%) Front 2 x 100W (6 ) Center 100W (6 ) Surround 2 x 100W (6 ) Power bandwidth both channels driven, -3 dB
7、10 Hz-70 kHz (6 , 0.9%) Damping factor 30 (6 ) Load impedance Front A or B 4-16 A and B 8-16 Center 6-16 Surround 6-16 Frequency response PHONORIAA standard curve (30 Hz- 15 kHz)0.8 dB CD ,TAPE/MD ,DVD ,TV ,VCR1 ,VCR210Hz-40 kHz, 3dB Input sensitivity and impeadance PHOTO 3 mV / 47 k CD ,TAPE/MD ,DV
8、D ,TV ,VCR1 ,VCR2 200 mV / 22 k S/N at rated power (6 ) PHONO70 dB (IHF, A: 80 dB) CD ,TAPE/MD ,DVD ,TV ,VCR1 ,VCR275 dB (IHF, A: 85 dB) DVD 6CH100 dB (IHF A, Rated Power, S=2 V), 75 dB (IHF, A :85 dB) Output voltage TAPE/MD REC (OUT), VCR 1 OUT200mV Tone controls BASS50 Hz, +10 to -10 dB TREBLE20 k
9、Hz, +10 to -10 dB Channel balance (250 Hz-6.3 kHz)1 dB Channel separation 55 dB Headphones output level and impeadance 430 mV / 330 Subwoofer frequency response (-6 dB) 7 - 200 Hz Digital input Optical2 Coaxicial1 4 General Power supply For Continental EuropeAC 230V, 50 Hz For the United Kingdom, Au
10、stralia and New Zealand AC 230-240 V, 50 Hz Power consumption230 W Dimensions (W x H x D)430 x 158 x 375 mm (16-15/16” x 6-7/32” x 14-25/32”) Mass10.0 kg (22 lb.) Power consumption in standby mode:2 W Notes: 1. Specifications are subject to change without notice. / Mass and dimensions are approximat
11、e. 2. Total harmonic distortion is measured by the digital spectrum analyzer. * Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. * Manufactured under license from Digital Theater System. “DTS” and “DTS Digital Surr
12、ound” are trademarks of Digital Theater System. 2001 Matsushita Electronics (S) Pte. Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law. 1. Before Repair and Adjustment Disconnect AC power, discharge Power Supply Capacitors C1702 through a 10 , 5 W resistor to grou
13、nd. DO NOT SHORT-CIRCUIT DIRECTLY (with a screw driver blade, for instance), as this may destroy solid state devices. After repairs are completed, restore power gradually using a variac, to avoid over current. Current consumption at AC 230 V, 50 Hz in NO SIGNAL mode should be 200600 mA (for E/EG 5 o
14、nly). Current consumption at AC 230 V/240 V, 50 Hz in NO SIGNAL mode should be 200600 mA (for EB only). 2. Protection Circuitry The protection circuitry may have operated if either of the following conditions are noticed: - No sound is heard when the power is turned on. - Stops during a performance.
15、 The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are “shorted”, or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used. If this occurs, follow the procedure outlines b
16、elow: 1. Turn off the power. 2. Determine the cause of the problem and correct it. 3. Turn on the power once again after one minute. Note: When the protection circuitry functions, the unit will not operate unless the power is first turned off and then on again. 3. Accessories AC Main Lead (E/EG). 1
17、pc. AC Main Lead (EB). 1 pc. AM Loop Antenna Set / . 1 set. 6 Antenna Plug (EB). 1 set. FM Indoor Antenna. 1 pc. Remote Control / Transmitter. 1 pc. 4. Caution for AC Mains Lead 7 5. Front Panel Controls 5.1. Front Panel 8 5.2. Remote Control 9 6. Disassembly and Main Component Replacement Procedure
18、s “ATTENTION SERVICER” Some chassis components maybe have sharp edges. Be careful when diassembling and servicing. 10 1. This section describes procedures for checking the operation of the major printed circuit boards and replacing the main components. 2. For reassembly after operation checks or rep
19、lacement, reverse the respective procedures. / Special reassembly procedures are described only when required. 3. Select items from the following index when checks or replacement are required. Content - Disassembly Procedure for each major P.C.B. . P.g. 79 - Main Component Replacement Procedures 1.
20、Replacement of the Power IC and Regulator Transistor. P.g. 10 2. Installation of the bottom cover after replacement. . P.g. 11 6.1. Disassembly Procedure for each major P.C.B. Step 1 Farads. - Resistance values are in ohms, unless specified otherwise, 1K= 1,000(ohms). - The marking (RTL) indicates t
21、hat the Retention Time is limited for this item. After the discontinuation of this assembly in production, the item will continue to be available for a specific period of time. The retention period of availability is dependant on the type of assembly, and in accordance with the laws govening part an
22、d product retention. After the end of this period, the assembly will no longer be available. - M indicates in the Remarks columns indicates parts that are supplied by MESA. - The “(SF)” mark denotes the standard part. - Remote Control Unit: Supply period for three years from terminal of production.
23、- Reference for O/I book languages are as follows : Ar : ArabicCf : Canadian FrenchCz : CzechDa : Danish Du : DutchEn : EnglishFr : FrenchGe : German It : ItalianKo : KoreanPo : PolishRu : Russian Sp : SpanishSw : SwedishCo : Traditional ChineseCn : Simplified Chinese 13.1. Cabinet 13.1.1. Cabinet P
24、arts Location 27 13.1.2. Cabinet Parts List 28 Ref. No.Part No.Part Name & DescriptionRemarks CABINET AND CHASSIS 1RAN0002EMTUNER MODULEM 2REM0080BFAN UNITM 3RGB0031-A1LTECH BADGEM 4RGK0995-2SSELECTOR RINGM 5RGK1337-SVOLUME RINGM 6RYQ0363-QHALF MIRROR UNITM 8RGL0533-QDIGITAL LIGHT GUIDEM 9RGL0535-QM
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Technics SADX1050 avr sm 维修 电路 原理图