Sony-STRK5800P-rec-sm维修电路原理图.pdf

上传人：cc518

文档编号：107770

上传时间：2024-07-17

格式：PDF

页数：52

大小：5.36MB

《Sony-STRK5800P-rec-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Sony-STRK5800P-rec-sm维修电路原理图.pdf（52页珍藏版）》请在收音机爱好者资料库上搜索。

1、1 SERVICE MANUALUS Model STR-K4800P/K5800P Canadian Model STR-K4800P AEP Model UK Model STR-DE497P STR-DE497P/K4800P/K5800P FM STEREO/FM-AM RECEIVER AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: (Models of area code US only) With 6 ohm loads, both channels driven, from 120 2

2、0,000 Hz; rated 80 watts (STR-K5800P)/ 60 watts (STR-K4800P) per channel minimum RMS power, with no more than 0.7 % total harmonic distortion from 250 milliwatts to rated output. Amplifier section Power Output 1) Models of area code US (6 ohms 1 kHz, THD 10 %) STR-K5800P:FRONT 2) : 120 W/ch CENTER 2

3、) : 120 W SURR 2) : 120 W/ch STR-K4800P:FRONT 2) : 100 W/ch CENTER 2) : 100 W SURR 2) : 100 W/ch Models of area code CND (6 ohms 1 kHz, THD 0.7 %) FRONT 2) : 80 W/ch CENTER 2) : 80 W SURR 2) : 80 W/ch (6 ohms 1 kHz, THD 10 %) FRONT 2) : 100 W/ch CENTER 2) : 100 W SURR 2) : 100 W/ch SPECIFICATIONS Mo

4、dels of area code AEP, UK (6 ohms 1 kHz, THD 0.7 %) FRONT 2) : 80 W/ch CENTER 2) : 80 W SURR 2) : 80 W/ch (6 ohms 1 kHz, THD 10 %) FRONT 2) : 100 W/ch CENTER 2) : 100 W SURR 2) : 100 W/ch 1) Measured under the following conditions: Area codePower requirements US, CND120 V AC, 60 Hz AEP, UK230 V AC,

5、50 Hz 2) Depending on the sound field settings and the source, there may be no sound output. Inputs (Analog) MULTI CH IN *, CD,Sensitivity: 800 mV MD/TAPE,Impedance: 50 kiloohms VIDEO 1, 2, DVD Inputs (Digital) DVD (Coaxial)Sensitivity: Impedance: 75 ohms VIDEO 2 (Optical)Sensitivity: Impedance: Ver

6、 1.1 2004. 10 9-879-027-02 2004J04-1 2004. 10 Sony Corporation Audio Group Published by Sony Engineering Corporation Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. “DTS” and “DTS Digital Surround” are registered

7、trademarks of Digital Theater Systems, Inc. Continued on next page Photo: STR-K5800P STR-DE497P/K4800P/K5800P are the FM/AM receiver section in HT-DDW760/4800DP/5800DP. RadioFans.CN 收音机爱好者资料库 2 STR-DE497P/K4800P/K5800P Outputs (Analog) MD/TAPE (OUT),Voltage: 800 mV VIDEO 1Impedance: 10 kiloohms (AU

8、DIO OUT) SUB WOOFERVoltage: 2 V Impedance: 1 kiloohms Reproduction frequency range: 28 20,000 Hz Tone Gain levels6 dB, 1 dB step * Models of area code AEP, UK only. FM tuner section Tuning range87.5 108.0 MHz AntennaFM wire antenna Antenna terminals75 ohms, unbalanced Intermediate frequency10.7 MHz

9、AM tuner section Tuning range Models of area code US, CND With 10-kHz tuning scale: 530 1,710 kHz 3) With 9-kHz tuning scale:531 1,710 kHz 3) Models of area code AEP, UK With 9-kHz tuning scale:531 1,602 kHz AntennaLoop antenna Intermediate frequency450 kHz 3) You can change the AM tuning scale to 9

10、 kHz or 10 kHz. After tuning in any AM station, turn off the receiver. While holding down PRESET TUNING + or TUNING +, press ?/1. All preset stations will be erased when you change the tuning scale. To reset the scale to 10 kHz (or 9 kHz), repeat the procedure. Video section Inputs/Outputs Video:1 V

11、p-p, 75 ohms General Power requirements Area codePower requirements US, CND120 V AC, 60 Hz AEP, UK230 V AC, 50/60 Hz Power consumption Area codePower consumption US (STR-K4800P)165 W US (STR-K5800P)180 W CND225 VA AEP, UK150 W Power consumption (during standby mode) 0.3 W Dimensions (w/h/d) (Approx.

12、) 430 145 310.5 mm (17 5 6/8 11 7/8 inches) including projecting parts and controls Mass (Approx.)6.5 kg (14 lb 6 oz) Design and specifications are subject to change without notice. Abbreviation CND : Canadian model RadioFans.CN 收音机爱好者资料库 3 MODEL IDENTIFICATION BACK PANEL Part No. MODELPART No. STR

13、-DE497P: AEP4-252-088-0s STR-DE497P: UK4-252-088-1s STR-K4800P: US4-252-088-2s STR-K4800P: CND4-252-088-3s STR-K5800P: US4-252-088-6s Abbreviation CND: Canadian model STR-DE497P/K4800P/K5800P 1.5 k0.15 F AC voltmeter (0.75 V) To Exposed Metal Parts on Set Earth Ground SAFETY CHECK-OUT After correcti

14、ng the original service problem, perform the follow- ing safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from an

15、y exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers.). Leakage current can be measured by any one of three methods. 1.A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. F

16、ollow the manufacturers instructions to use these instruments. 2.A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3.Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indica- tion is 0.75

17、 V, so analog meters must have an accurate low- voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex- amples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suit- able. (See Fig. A) Fig. A. Using an AC voltmeter to check AC leakage.

18、 SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY

19、. ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES S

20、UPPLMENTS PUBLIS PAR SONY. 4 STR-DE497P/K4800P/K5800P TABLE OF CONTENTS 1. GENERAL Main unit (STR-DE497P) . 5 Main unit (STR-K4800P/K5800P). 7 Remote button description. 9 2. DISASSEMBLY 2-1. Case .10 2-2. Front Panel Section .11 2-3. Back Panel. 11 2-4. Digital Board. 12 2-5. Standby Board .12 2-6.

21、 Main Board .13 3. TEST MODE. 14 4. DIAGRAMS 4-1. Circuit Boards Location . 15 4-2. Block Diagram Tuner/Audio Section . 16 4-3. Block Diagram Digital Section .17 4-4. Block Diagram Video/Display Section .18 4-5. Block Diagram Power Section . 19 4-6. Printed Wiring Boards Main Section . 20 4-7. Schem

22、atic Diagram Main Section (1/2) . 21 4-8. Schematic Diagram Main Section (2/2) . 22 4-9. Printed Wiring Board Digital Section (1/2) . 23 4-10. Printed Wiring Board Digital Section (2/2) . 24 4-11. Schematic Diagram Digital Section (1/2) .25 4-12. Schematic Diagram Digital Section (2/2) .26 4-13. Pri

23、nted Wiring Board Video Section .27 4-14. Schematic Diagram Video Section . 27 4-15. Printed Wiring Boards Display Section . 28 4-16. Schematic Diagram Display Section .29 4-17. Printed Wiring Boards Power Section . 30 4-18. Schematic Diagram Power Section . 31 4-19. IC Block Diagrams. 32 5. EXPLODE

24、D VIEWS 5-1. Case Section . 37 5-2. Front Panel Section .38 5-3. Chassis Section-1 . 39 5-4. Chassis Section-2 . 40 6. ELECTRICAL PARTS LIST. 41 5 STR-DE497P/K4800P/K5800P SECTION 1 GENERALThis section is extracted from instruction manual. STR-DE497P: 6 STR-DE497P/K4800P/K5800P STR-DE497P: 7 STR-DE4

25、97P/K4800P/K5800P STR-K4800P/K5800P: 8 STR-DE497P/K4800P/K5800P STR-K4800P/K5800P: 9 STR-DE497P/K4800P/K5800P 10 STR-DE497P/K4800P/K5800P Note : This set can be disassemble according to the following sequence. SECTION 2 DISASSEMBLY 2-1. CASE 2-1.CASE (Page 10) 2-2.FRONT PANEL SECTION (Page 11) 2-3.B

26、ACK PANEL (Page 11) SET 2-5.STANDBY BOARD (Page 12) 2-4.DIGITAL BOARD (Page 12) 2-6.MAIN BOARD (Page 13) Note : Follow the disassembly procedure in the numerical order given. 1 two screws (tapping) 2 three screws (tapping) 3 two screws (tapping) 4 case 11 STR-DE497P/K4800P/K5800P 2-2. FRONT PANEL SE

27、CTION 2-3. BACK PANEL 5 front panel section 1 CNS4 2 CNP791 3 three screws (BVTP3 x 8) 4 two screws (BVTP3 x 8) 1 CNS7 3 CNP156 5 CNP901 4 CNP801 2 CNS8 8 two screws (BVTP3 x 8) qa four screws (BVTP3 x 8) qs back panel 9 two screws (BVTP3 x 8) 0 five screws (BVTP3 x 8) 7 two screws (BVTP3 x 8) 6 scr

28、ew (BVTP3 x 8) 12 STR-DE497P/K4800P/K5800P 2-4. DIGITAL BOARD 4 CNS1 5 CNS2 1 CNP6 2 CNP5 8 bracket (digital) 6 DIGITAL board 3 screw (BVTP3 x 8) 7 screw (BVTP3 x 8) 7 STANDBY board 1 CNP915 4 CNP804 5 CNP903 2 CNP802 3 CNP902 6 three screws (BVTP3 x 8) 2-5. STANDBY BOARD 13 STR-DE497P/K4800P/K5800P

29、 5 MAIN board 1 two screws (+BV SUMITITE (B3) 2 two screws (+BV SUMITITE (B3) 4 two screws (+BV SUMITITE (B3) 3 screw (+BV SUMITITE (B3) 2-6. MAIN BOARD 14 STR-DE497P/K4800P/K5800P SECTION 3 TEST MODE FACTORY PRESET MODE * All preset contents are reset to the default setting. * Procedure: While depr

30、essing the MAIN MENU and the PRESET TUNING - buttons simultaneously, press the ?/1 button to turn on the main power. The message “FACTORY” appears for a moment and the present contents are reset to the default values. AM CHANNEL STEP 9 kHz/10 kHz SELECTION MODE (US, Canadian model only) * Either the

31、 9 kHz step or 10 kHz step can be selected for the AM channel step. * Procedure: Press the TUNER FM/AM button to set AM and press the ?/1 button to turn off the main power. While depressing the TUNING + button or the PRESET TUNING + button, press the ?/1 button to turn on the main power. Either the

32、message “9k STEP” or “10k STEP” appears for a moment and select the desired step. SPEAKER SIZE SELECTION MODE * Either the normal speaker or micro satellite speaker can be se- lected. * Procedure: While depressing the DIMMER button, press the ?/1 button to turn on the main power. Either the message

33、“NORM. SP.” or “MICRO SP.” appears for a moment and select the desired speaker size. VACUUM FLUORESCENT DISPLAY TEST MODE * All fluorescent segments are tested. When this test is activated, all segments light on at the same time, then each segment lights on one after another. * Procedure: While depr

34、essing the MOVIE and the buttons simultaneously, press the ?/1 button to turn on the main power. 1.ALL segments light on. 2CH, A.F.D., MOVIE, MUSIC and MULTI CHANNEL DE- CODING LED light on. 2.Press the VIDEO 1 button, confirm display. A.F.D. and MUSIC LED light on. 3.Press the VIDEO 1 button, confi

35、rm display. 2CH, MOVIE and MULTI CHANNEL DECODING LED light on. 4.Press the VIDEO 1 button, all segments and all LEDs light off. 5.Every pressing the VIDEO 1 button turns on each segment and LED one after another in the same order. (Not only the VIDEO 1 button, but also the other buttons such as VID

36、EO 2, DVD, MD/TAPE, CD and TUNER FM/AM can be used.) SOUND FIELD CLEAR MODE * The preset sound field is cleared when this mode is activated. Use this mode before returning the product to clients upon completion of repair. * Procedure: While depressing the 2CH button, press the ?/1 button to turn on

37、the main power. The message “SF. CLR.” appears for a moment and initializa- tion is performed. SOFTWARE VERSION DISPLAY MODE * The software version is displayed. * Procedure: While depressing the FM MODE and the DISPLAY buttons si- multaneously, press the ?/1 button to turn on the main power. The mo

38、del name, destination and the software version are dis- played for a moment. KEY CHECK MODE * Button check * Procedure: While depressing the TUNER FM/AM and the A.F.D. buttons simultaneously, press the ?/1 button to turn on the main power. Either the message “REST 26” (STR-DE497P) or “REST 25” (STR-

39、K4800P/K5800P) appears. Every pressing of any button other than the ?/1 counts down the buttons. The buttons which are already counted once are not counted again. When all buttons are pressed “REST 00” appears. AUTOBETICAL MODE (AEP, UK model only) * When this mode is used, the receiver scans the br

40、oadcasts that can be received by the tuner, and sets up the broadcasts. Be sure to start scanning after connecting the antenna. * Procedure: Check that the antenna is connected. While depressing the MEMORY button, press the ?/1 button to turn on the main power. The message “AUTO-BETICAL SELECT” appe

41、ars for a mo- ment and the receiver starts scanning. COMMAND MODE SELECTION MODE * The command mode (AV1 or AV2) of the remote commander can be selected. * Procedure: While depressing the ENTER button, press the ?/1 button to turn on the main power. Either the message “C.MODE.AV 1” or “C.MODE.AV 2”

42、ap- pears for a moment and select the desired mode. L SW CR SLSSR SBLSBSBR LFESP A SP B SLEEP OPT COAX MULTI CH IN 96/24 DIGITALEXPRO LOGIC II x DTS-ESNEO:6 MPEG-2 AAC RDS D.RANGE EQ STEREO MONO DDDD dB kHz mft. MHz MEMORY DIRECT L SW R S SB LFESP A SP B SLEEP OPT COAX MULTI CH IN 96/24 DIGITALEXPRO

43、 LOGIC II x DTS-ESNEO:6 MPEG-2 AAC RDS D.RANGE EQ STEREO MONO DDDD dB kHz mft. MHz MEMORY DIRECT C SLSR SBLSBR SP A SP B SLEEP OPT COAX MULTI CH IN 96/24 DIGITALEXPRO LOGIC II x DTS-ESNEO:6 MPEG-2 AAC RDS D.RANGE EQ STEREO MONO DDDD kHz mft. MHz MEMORY DIRECT STR-DE497P/K4800P/K5800P 1515 STR-DE497P

44、/K4800P/K5800P SECTION 4 DIAGRAMS 4-1. CIRCUIT BOARDS LOCATION POWER board STANDBY board VIDEO board DIGITAL board MAIN board TUNING board DISPLAY board THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) for schematic diagram: All capacitors are in F unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in and 1/4 W or less unless otherwise specified. f: internal component. 2 : nonflammable resistor. 5 : f