Sony-STRDE635-rec-sm维修电路原理图.pdf

《Sony-STRDE635-rec-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Sony-STRDE635-rec-sm维修电路原理图.pdf（58页珍藏版）》请在收音机爱好者资料库上搜索。

1、STR-DE635 US Model Canadian Model AEP Model SERVICE MANUAL FM STEREO FM-AM RECEIVER Continued on next page SPECIFICATIONS Manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double-D symbol a are trademarks of Dolby Laboratories Licensing Corporation. Ver 1.1 20

2、02. 02 Sony Corporation Home Audio Company Published by Sony Engineering Corporation 9-928-897-12 2002B1600-1 2002.02 AUDIO POWER SPECIFICATIONS: POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 8 loads, both channels driven, from 20 20,000 Hz; rated 80 W per channel minimum RMS power, with no more

3、than 0.09% toral harmonic distortion from 250 mW to rated output (USA model only). Amplifier section Stereo modeUSA, Canadian models: (8 20Hz 20kHz, THD 0.09%) 80W + 80W AEP model: (4 DIN, 1kHz) 70W + 70W Surround modeUSA, Canadian models: (8 at 1kHz, THD 0.8%) Front: 80W + 80W Centera): 80W Reara):

4、 80W + 80W AEP model: (4 DIN, 1kHz) Front: 70W + 70W Centera): 70W Reara): 70W + 70W a) Depending on the sound field settings and the source, there may be no sound output. Dynamic power output145W + 145W, 8 210W + 210W, 4 Frequency responsePHONO: RIAA equalization curve 0.5 dB USA, Canadian models:

5、CD, MD/TAPE, DVD/LD, TV/SAT, VIDEO1,2: AEP model: CD, MD/TAPE, DVD, TV/LD, VIDEO1,2: 10Hz 50kHz + 0.5/2dB (with sound field, equalizer, and bass boost bypassed) Inputs (Analog)PHONO: Sensitivity: 2.5mV Impedance: 50k S/Nb): 86dB (A, 2.5mVc) USA, Canadian models: 5.1CH INPUT, CD,DVD/LD,MD/TAPE,TV/ SA

6、T,VIDEO1,2: AEP model 5.1CH INPUT, CD,DVD,MD/TAPE,TV/ LD,VIDEO1,2: Sensitivity: 150mV Impedance: 50k S/Nb): 96dB (A, 150mVc) b) Input short c) Weighted network, input level RadioFans.CN 收音机爱 好者资料库 2 Inputs (Digital)DVD/LD (coaxial): Sensitivity: Impedance: 75 S/N: 100dB (A, 20kHz LPF) DVD/LD (Optica

7、l): Sensitivity: Impedance: S/N: 100dB (A, 20kHz LPF) OutputsMD/TAPE, (REC OUT); VIDEO1,2 (AUDIO OUT): Voltage: 150mV, Impedance: 10k SUB WOOFER: Voltage:2V Impedance: 1k PHONES: Accepts low-and high-impedance headphones BASS BOOST+6dB at 70Hz Sampling Frequency48kHz EQBASS: 100Hz 1.0kHz (21steps) M

8、ID: 500Hz 5.0kHz (21steps) TABLE: 1.0kHz 10kHz (21steps) Gain levels: 10dB, 1dB step FM tuner section Tuning range87.5 108.0MHz Antenna terminals75, unbalanced SensitivityMono: 18.3dBf, 2.2V/75 Stereo: 38.3dBf, 22.5V/75 Usable sensitivity11.2dBf, 1V/75 S/NMono: 76dB Stereo: 70dB Harmonic destortion

9、at 1kHz Mono: 0.3% Stereo: 0.5% Separetion45dB at 1kHz Frequency response30Hz 15kHz + 0.5/2dB Selectivity60dB at 400kHz AM tuner section Tuning rangeUSA, Canadian models: With 10-kHz tuning scale: 530 1,710kHzd) With 9-kHz tuning scale: 531 1,710kHzd) AEP model 531 1,602kHz AntennaLoop antenna Usabl

10、e sensitivity50dB/m (at 1,000kHz or 999kHz) S/N54dB (at 50mV/m) Harmonic destortion0.5% (50mV/m, 400kHz) SelectivityAt 9kHz: 35dB At 10kHz: 40dB d) You can change the AM tuning scale to 9kHz. After tuning in any AM station, turn off the receiver. Hold down the TUNING+ button and press the 1/u button

11、. All preset stations will be erased when you change the tuning scale. To reset the scale to 10kHz, repeat the procedure. Video section Inputs1Vp-p 75 Outputs1Vp-p 75 General SystemTuner section: PLL quartz-locked digital synthesizer system Preamplifier section: Low-noise NF type equalizer Power amp

12、lifier section: Pure-complementary SEPP Power requirementsUSA, Canadian models: 120V AC, 60Hz AEP model 230V AC, 50/60Hz Power consumptionUSA: 270W Canada: 285VA AEP: 200W AC outletsUSA, Canadian models: 2switched, total 100W AEP model 1switched, max 100W Dimensions430 364 157.5mm (17 145/16 61/4 in

13、.) including projecting parts and controls Mass (Approx.)USA, Canadian models: 9.5kg (20 lbs. 15 oz.) AEP model 10.1kg Supplied accessories FM wire antenna (1) AM loop antenna (1) Remote commander RM-PP402 (remote) (1) R6 (size-AA) batteries (2) FM antenna adapter (1) Design and specifications are s

14、ubject to change without notice. RadioFans.CN 收音机爱 好者资料库 3 SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR A

15、S SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFS PAR UNE MARQUE ! SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PISES SON

16、Y DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPMENTS PUBLIS PAR SONY. TABLE OF CONTENTS SAFETY CHECK-OUT (US model only) After correcting the original service problem, perform the following safety checks before releasing the set to the customer: Check the antenna terminals, metal trim,

17、“metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microa

18、mpers). Leakage current can be measured by any one of three methods. 1.A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2.A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for

19、this job. 3.Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all batte

20、ry operated digital multimeters that have a 2V AC range are suitable. (See Fig. A) Earth Ground AC voltmeter (0.75V) 1.5k0.15F Fig. A. Using an AC voltmeter to check AC leakage. To Exposed Metal Parts on Set 1. GENERAL 4 2. SERVICEING NOTE 6 3. TEST MODE 6 4. DIAGRAMS 4-1.Block Diagram Main Section

21、7 4-2.Block Diagram Power Section 9 4-3.Circuit Board Location 11 4-4.Schematic Diagram Digital Section(1/3) 13 4-5.Schematic Diagram Digital Section(2/3) 15 4-6.Schematic Diagram Digital Section(3/3) 17 4-7.Printed Wiring Board Digital Section(1/2) 19 4-8.Printed Wiring Board Digital Section(2/2) 2

22、1 4-9.Printed Wiring Board Display Section 23 4-10. Schematic Diagram Display Section 25 4-11. Printed Wiring Board Surround Section 27 4-12. Schematic Diagram Surround Section 29 4-13. Printed Wiring Board Rear AMP Section31 4-14. Schematic Diagram Rear AMP Section 33 4-15. Printed Wiring Board Pow

23、er Section 35 4-16. Schematic Diagram Power Section 37 4-17. Printed Wiring Board Video Section 39 4-18. Schematic Diagram Video Section 41 4-19. Printed Wiring Board Main Section 43 4-20. Schematic Diagram Main Section(1/2) 45 4-21. Schematic Diagram Main Section(2/2) 47 4-22. IC Pin Function 49 4-

24、23. IC Block Diagrams59 5. EXPLODED VIEWS 5-1.Front Panel Section 62 5-2.Chassis Section 63 6. ELECTRICAL PARTS LIST64 4 SECTION 1 GENERAL Identifying the Parts Front Panel 11/u switch 2Function buttons 3INPUT MODE button 45.1CH INPUT button 5MASTER VOLUME control 6MUTING button 7SPEAKERS selector P

25、HONES jack 8DISPLAY button 9DIMMER button 0A.F.D button/indicator MODE button/indicator 2CH button/indicator !MULTI CHANNEL DECODING indicator !BASS BOOST button !EQUALIZER button !DIRECT button SHIFT button Numeric buttons (0 to 9) AM button (US, Canadian models) RDS EON button (US, Canadian models

26、) FM button (US, Canadian models) AM/FM button (AEP model) FM MODE button MEMORY button !TUNNIG +/- buttons PRESET +/- buttons !LEVEL button !SUR button !EQ button !Cursor buttons() Jog dial SET UP button NAME button ENTER button RDS PTY button (AEP model) 5 6 SECTION 3 TEST MODE FLUORESCENT INDICAT

27、OR TUBE TEST MODE * All fluorescent segments are tested. When this test is activated, all segments turn on at the same time, then each segment turns on one after another. * Procedure: While depressing the ENTER, the LEVEL and the EQ buttons simultaneously, press the power 1/u button to turn on the m

28、ain power. All segments turn on at the same time, then each segment turns on press the ENTER button. FACTORY SET MODE * All preset contents are reset to the default setting. * Procedure: While depressing the SET UP, the LEVEL and the ENTER buttons simultaneously, press the power 1/u button to turn o

29、n the main power. The message Factry Set appears and the present contents are reset to the default values. ALL CLEAR MODE * All preset contents are cleared when this mode is activated. Use this mode before returning the product to clients upon completion of repair. * Procedure: While depressing the

30、SET UP button simultaneously, press the power 1/u button to turn on the main power. The machine enters the DEMO mode.DEMO mode: Wait a while, then the demonstration starts. If the power 1/u button is pressed often the demonstration has started, the power is turned off, and the demonstration resumes

31、if the power 1/u button is pressed again. ALL CLEAR mode; If the power 1/u button is pressed often the machine enters the DEMO mode, but before the demonstration starts, the display is turned off. Press 1/u again. No response is returned. The press 1/u again. The preset data is cleared and the machi

32、ne enters the normal power-on state. SOUND FIELD CLEAR MODE * The preset sound field is cleared when this mode is activated. Use this mode before returning the product to clients upon completion of repair. * Procedure: While depressing the SOUND FIELD MODE button, press the power 1/u button to turn

33、on the main power. The message S.F Initialize appears and initialization is performed. AM CHANNEL STEP 9 kHz/10 kHz SELECTION MODE (US, Canadian models) * Either the 9 kHz step or 10 kHz step can be selected for the AM channel step. * Procedure: Set the FUNCTION to AM. Turn off the main power. While

34、 depressing the TUNING+ button or the PRESET TUNING + button, press the power 1/u button to turn on the main power. Either the message AM 9kHz Step or AM 10kHz Step appears. Select the desired step. DSP TEST MODE * It tests whether the DSP works correctly or not. When the DSP test is activated, the

35、test data is output from the DSP (IC1401: CXD2712R) of the DIGITAL board and is written in the RAM (IC1402: IDT71V016S). When the test data is read from the RAM by the DSP, the data output must be equivalent to the original data. If they disagree, an error is triggered. Errors can be caused by the b

36、roken data line or defective soldering. * Procedure While pressing the SETUP, LEVEL and SUR buttons, press the POWER button to enter the DSP test mode. The message DSP TEST MODE appears. When an error occurs, the message DSP2 ERROR is displayed. When there is no error, the message DSP2 NO ERROR appe

37、ars and the 1 kHz signal is output to all channels. Then, the mode can be switched the (SIGN WAVE) (THROUGH) and (INPULSE) mode. AUTOBETICAL MODE (AEP Model only) * This mode is installed in the Europe models only. When this mode is used, the receiver scans the broadcasts that can be received by tun

38、er, and sets up the broadcasts. Be sure to start scanning after connecting the antenna. Procedure: Check that the antenna is connected. Press the POWER button while pressing the MEMORY button to turn on the power. The message “Autobetical select” appears and scanning starts by tuner. VERSION MODE *

39、When this mode is used, the microprocessor version number is displayed. * Procedure: Press the POWER button while pressing the ENTER, LEVEL, and SUR buttons to turn on the power. The microprocessor version number appears as follows. SECTION 2 SERVICING NOTE 1. When the front panel is removed, the VR

40、 board is removed at the same time. Consequently the LEDs cannot be turned on and the sound volume cannot be increased or decreased from the remote control. 2. When servicing the DIGITAL board, be sure to connect the earth land of the DIGITAL board with the chassis frame so that the earth potential

41、of the DIGITAL board must not be floated from the chassis frame. Rear Panel 1234567 8 90!?!?!?!?!?!?!?!?!? 1ANTENNA 2DIGITAL 35.1 CH INPUT 4SPEAKERS (FRONT) 5SPEAKERS (REAR) 6SPEAKERS (CENTER) 7WOOFER 8INPEDANCE SELECTOR 9AC power cord !AC OUTLET !S-LINK !VIDEO 1 !VIDEO 2 !DVD/LD (US, Canadian model

42、s) DVD (AEP model) !TV/SAT (US, Canadian models) TV/LD (AEP model) !MONITOR !MD/TAPE !CD !PHONO STR-DE635 7 8 SECTION 4 DIAGRAMS L 58 DATA FM AM FM 75 AM DO TUNED T. MUTE STEREO DATA CLK CE L OUT R OUT TUNER UNIT DO TUNED MUTING STEREO S DATA S CLK S LAT R CH : FM : CD Signal Path RCH is omitted PHO

43、NO LCD J301 LINPUT LOUTPUT J302 J001 MD/TAPE M OUT1 J201 MONITOR J202 J203 TV/LD DVD VIDEO 2 VIDEO 1 V1 IN13 V1 OUT15 V2 IN9 V2 OUT11 TV3 LD5 8VEE 16VCC 14SW1 10SW2 4SW3 6SW4 32 VIDEO SELECT IC201 -5V REG IC202 -15V +5V 4 3 2 8 6 11 5 9 12 CONTROL CE 16 CLK 14 DI 15 AUDIO SELECT IC301 MUTE Q1502 S L

44、AT S CLK S DATA EQ AMP IC302 MUTE Q1506 IC1508 MUTE Q1505 VIDEO(SW1)77 SYSTEM CONTROL IC1201 VIDEO(SW2)76 VIDEO(SW3)75 VIDEO(SW4)72 16 59 AUTO STOP 60 STEREO 84 TUNER MUTE S DATA S CLK S LAT DO TUNED STEREO TMUTE 56 DATA 57 CLOCK 55 LATCH D : PHONO 27 26 24 22 23 17 CONTROL CE 16 CLK 14 DI 15 SELECT

45、OR IC303 S LAT S CLK S DATA 25 20 D201 LTV/SAT L J305 VIDEO2 INPUT INPUT LOUTPUT L VIDEO1 OUTPUT LINPUT J304 TM301 ANTENNA 414 15 13231 10 12 10 LINPUT DVD/LD 21 IR LINK DET IC001 DVD DVDOPT COAXIAL IC007 INPUT OUTPUT INPUT INPUT OUTPUT OUTPUT DVD/LD TV/SAT INPUT US,Canadian MODEL AEP MODEL 5 6 9 SE

46、LECT SWITCH IC1005 7 B A14 2 B A IC1006 112 DI 108 DIG IN A 107 DIG IN B A B 110 CL 111 CE 115 BY SYNC 113 DO DIGITAL AUDIO I/F RECEIVER IC1101 D IN3 BP SYNC33 DI36 CLK38 CE37 16DATA 13CK OUT 14BCK 2212.288M 34ERROR 35DO X3501 12.288MHz IC1404 IC1404 XI8 SDIA084 SDIA185 SDWCK082 DOLBY DIGITAL AUDIO

47、DECODER IC1301 24AUDATA0 23AUDATA1 22AUDATA2 D0-7 SCK 69 1 SCCLK SI 68 CS 66 IC 62 2 SI 4 CS 5 IC 67SO 3 SO 114 D1202 106 ANALOG/DIG ERROR A0-7 D0-7 SRAM IC1402 SIA117 SIB118 SIC119 XWE74 XOE70 16 20 23 25 . HD0 HD7 D0-7 HD0HD7 13 XHDWR 25 HA0 AUDIO DSP IC1401 HA015 XHDWR 9 XHDCS 14 XRST 26 16 XHDCS

48、 27 HRDY 26 XRST 13HRDY 5SOD 15 SOD 30 CDTI IC1202 IC1202 Q1201 Q1202 31 CDTO 29 CCLK 28 CS 32 PD 2SOA LRCK1116 LRCK0115 BCK1114 3SOB 4SOC 27L OUT1 LIN-29 AUDIO CODEC IC1503 CDTO 44 CDTI 43 CCLK 42 CS 41 PD 17 SDTO9 MCLK139 BCLK4 LRCK5 SDTI 16 SDTI 27 SDTI 38 LIN+30 IC1504IC1504 23L OUT3 IC1508 IC15

49、09 MUTE Q1504 IC1510 24R OUT3 25L OUT2 IC1507 IC1505 IC1505 IC1506 MUTE CONT Q1507 Q1204 U DATA50DISP DATA 52DISP CLK 49DISP MR 51SREQ 10SOTO 9SINO 87MD2 89MD0 90RESET U CLOCK U MREQ U SREQ SOT0 SIN1 MD2 MD0 U REST 105RY POWERRY POWER AC MUTE PROTECT RY HP RY FRONT A RY FRONT B RY CENTER RY WOOFER RY REAR AC MUTE PROTECTOR HP RY SP/A RY SP/B RY RY CENTER RY WOOFER REAR SP RY C 92 XO 93 XI X1201 16MHz 67STOPSTOP : DVD IC11404 AEP ONLY 9FM DET4 2 1314 RDS IC1 X1 4.33MHz 6ANT LEVEL 16 ANT LEVEL RDS DATA RDS CLK A 2SW5 S