Sony-STRDE495P-rec-sm维修电路原理图.pdf

《Sony-STRDE495P-rec-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Sony-STRDE495P-rec-sm维修电路原理图.pdf（42页珍藏版）》请在收音机爱好者资料库上搜索。

1、STR-DE495P/K750P US Model Canadian Model STR-K750P AEP Model UK Model STR-DE495P E Model Australian Model STR-K750P SERVICE MANUAL FM STEREO FM-AM RECEIVER Continued on next page SPECIFICATIONS Ver 1.1 2004. 08 Dolby Laboratories Licensing Corporation. “DOLBY” the double-D symbol ; “AC-3” and “PRO L

2、OGIC” are trademarks of Dolby Laboratories Licensing Corporation. Photo : STR-K750P Sony Corporation Audio Group Published by Sony Engineering Corporation 9-877-046-02 2004H16-1 2004.08 STR-DE495P/K750P are the tuner and the amplifier section in HT-DDW750. POWER OUTPUT AND TOTAL HARMONIC DISTORTION:

3、 With 8 ohm loads, both channels driven, from 40 20,000 Hz; rated 90 watts per channel minimum RMS power, with no more than 0.7 % total harmonic distortion from 250 milliwatts to rated output (Models of area code U only). Amplifier section POWER OUTPUT Models of area code U, CA Rated Power Output at

4、 Stereo Mode (8 ohms 40 Hz 20 kHz, THD 0.7 %) STR-K750P:90 W + 90 W Reference Power Output (8 ohms 1 kHz, THD 0.7 %) STR-K750P:FRONT1):100 W/ch CENTER1): 100 W SURR1): 100 W/ch Models of area code CEL,CEK Rated Power Output at Stereo Mode (8 ohms 1 kHz, THD 0.7 %) STR-DE495P:80 W + 80 W2) Reference

5、Power Output2) (8 ohms 1 kHz, THD 0.7 %) STR-DE495P:FRONT1): 80 W/ch CENTER1): 80 W SURR1): 80 W/ch Models of area code MX Rated Power Output at Stereo Mode (8 ohms 1 kHz, THD 0.7 %) STR-K750P:90 W + 90 W Reference Power Output (8 ohms 1 kHz, THD 0.7 %) STR-K750P:FRONT1): 90 W/ch CENTER1): 90 W SURR

6、1): 90 W/ch Models of other area code Rated Power Output at Stereo Mode (8 ohms 1 kHz, THD 0.7 %) STR-K750P:90 W + 90 W2) Reference Power Output2) (8 ohms 1 kHz, THD 0.7 %) STR-K750P:FRONT1): 90 W/ch CENTER1): 90 W SURR1): 90 W/ch 1) Depending on the sound field settings and the source, there may be

7、 no sound output. 2) Measured under the following conditions: Area codePower requirements E2/E3120/220/240 V AC, 50/60 Hz SP, CEL, CEK230 V AC, 50 Hz Frequency response CD, MD/TAPE, DVD, VIDEO 1, 2 Inputs (Analog) CD, MD/TAPE, DVD, VIDEO 1, 2 3) INPUT SHORT (with sound field and tone bypassed). 4) W

8、eighted network, input level. 10 Hz 50 kHz +0.5/2 dB (with sound field and tone bypassed) Sensitivity: 500 mV Impedance: 50 kilohms S/N3): 96 dB (A, 500 mV4) RadioFans.CN 收音机爱 好者资料库 2 STR-DE495P/K750P Design and specifications are subject to change without notice. Abbreviation CA: Canadian model. CE

9、L: AEP model. CEK: UK model. SP: Singapore model. (Malaysia model included.) MX: Mexican model. AU: Australian model FM tuner section Tuning range87.5 - 108.0 MHz Antenna terminals75 ohms, unbalanced Intermediate Frequency 10.7 MHz Sensitivity Mono:18.3 dBf, 2.2 V/75 ohms Stereo:38.3 dBf, 22.5 V/75

10、ohms Usable sensitivity11.2 dBf, 1 V/75 ohms S/N Mono:76 dB Stereo:70 dB Harmonic distortion at 1 kHz Mono:0.3% Stereo:0.5% Separation45 dB at 1 kHz Frequency response30 Hz 15 kHz, +0.5/2 dB Selectivity60 dB at 400 kHz AM tuner section Tuning range Models of area code U, CA With 10-kHz tuning scale:

11、 530 1710 kHz5) With 9-kHz tuning scale:531 1710 kHz5) Models of area code E2/E3 With 10-kHz tuning scale: 530 1610 kHz5) With 9-kHz tuning scale:531 1602 kHz5) Models of area code CEL, CEK, SP, AU With 9-kHz tuning scale:531 1602 kHz Models of area code MX With 10-kHz tuning scale: 530 1610 kHz Ant

12、ennaLoop antenna Intermediate Frequency 450 kHz Usable sensitivity50 dB/m (at 1,000 kHz or 999 kHz) S/N54 dB (at 50 mV/m) Harmonic distortion0.5 % (50 mV/m, 400 Hz) Selectivity At 9 kHz:35 dB At 10 kHz:40 dB 5) You can change the AM tuning scale to 9 kHz or 10 kHz. After tuning in any AM station, tu

13、rn off the receiver. Hold down PRESET TUNING + and press ?/1. All preset stations will be erased when you change the tuning scale. To reset the scale to 10 kHz (or 9 kHz), repeat the procedure. Video section Inputs Video:1 Vp-p, 75 ohms Outputs Video:1 Vp-p, 75 ohms General Power requirements Area c

14、odePower requirements U, CA, MX120 V AC, 60 Hz CEL, CEK230 V AC, 50/60 Hz SP220 230 V AC, 50/60 Hz E2/E3120/220/240 V AC, 50/60 Hz AU240 V AC, 50Hz Power consumption Area codePower consumption U, MX185 W CA270 VA CEL, CEK, SP, AU 180 W E2/E3190 W Power consumption (during standby mode) 0.3 W Dimensi

15、ons430 145 298 mm (16 7/8 5 6/8 11 6/8 inches) including projecting parts and controls Mass (Approx.)7.2 kg (15 lb 14 oz) Sensitivity: Impedance: 75 ohms S/N: 100 dB (A, 20 kHz LPF) Sensitivity: Impedance: S/N: 100 dB (A, 20 kHz LPF) Inputs (Digital) DVD (Coaxial) VIDEO 2 (Optical) Outputs MD/TAPE (

16、OUT), VIDEO 1 (AUDIO OUT) SUB WOOFER Tone Gain levels:6 dB, 1 dB step Voltage: 500 mV Impedance: 10 kilohms Voltage: 2 V Impedance: 1 kilohms RadioFans.CN 收音机爱 好者资料库 3 STR-DE495P/K750P SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGR

17、AMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. After correcting the original service problem, perform the following safety checks before releasing the set to the

18、 customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a r

19、eturn to chassis, must not exceed 0.5 mA (500 microamperes). Leakage current can be measured by any one of three methods. 1.A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2.A battery-operated AC milliammeter. The D

20、ata Precision 245 digital multimeter is suitable for this job. 3.Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are example

21、s of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2V AC range are suitable. (See Fig. A) SAFETY CHECK-OUT ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT

22、CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PISES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPMENTS PUBLIS PAR SONY. To Exposed Metal Parts on Set 0.15 F 1.5 k AC Voltmeter (0.75 V) Earth Ground Fig. A. Using an AC voltmeter to check AC leak

23、age. Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat. Unleaded solder Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. (Ca

24、ution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) : LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40C higher than ordinary solder. Ordinary soldering irons can be used but th

25、e iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder

26、is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. 4 STR-DE495P/K750P TABLE OF CONTENTSM

27、ODEL IDENTIFICATION BACK PANEL Parts No. MODELPARTS No. US model4-244-031-0s Canadian model4-244-031-1s Australian model4-244-031-2s Singapore model4-244-031-3s E4-244-031-4s AEP model4-244-031-5s UK model4-244-031-6s Mexican model4-244-031-7s 1. GENERAL5 2. TEST MODE6 3. DIAGRAMS 7 3-1.Circuit Boar

28、d Location 7 3-2.Block Diagrams MAIN Section 8 DISPLAY/POWER Section 9 3-3.Printed Wiring Board DIGITAL Board (SIDE A) 10 3-4.Printed Wiring Board DIGITAL Board (SIDE B) 11 3-5.Schematic Diagram DIGITAL Section (1/2) 12 3-6.Schematic Diagram DIGITAL Section (2/2) 13 3-7.Printed Wiring Board MAIN Boa

29、rd 14 3-8.Schematic Diagram MAIN Section (1/3) 15 3-9.Schematic Diagram MAIN Section (2/3) 16 3-10. Schematic Diagram MAIN Section (3/3) 17 3-11. Printed Wiring Board POWER Section 18 3-12. Printed Wiring Board DISPLAY Board 19 3-13. Schematic Diagram DISPLAY Section 20 3-14. Printed Wiring Board VI

30、DEO Section 21 3-15. Schematic Diagram VIDEO Board 22 3-16. IC Block Diagrams 23 3-17. IC Pin Function Descriptions 25 4. EXPLODED VIEWS 27 4-1. Front Panel Section 27 4-2. Chassis Section 28 5. ELECTRICAL PARTS LIST 29 5 STR-DE495P/K750P SECTION 1 GENERALThis section is extracted from instruction m

31、anual. qd 2 M O MAIN MENU qf (15, 26, 27, 33, 34, 51) MASTER VOLUME qs (18, 20, 44) MD/TAPE 8 (20) MEMORY wg (28, 30) MENU +/ qh (15, 26, 27, 33, 34, 51) MENU qj (15, 26, 27, 33, 34, 51) MOVIE (button/indicator) ql (23, 45) MUSIC (button/indicator) qk (23, 24, 45) P Z PHONES (jack) wh (20, 25, 45) P

32、RESET TUNING +/ ws (30, 48) TUNER FM/AM q; (20, 29, 30, 33) TUNING +/ wd (29) VIDEO 1 5 (20) VIDEO 2 6 (20) NUMBERS AND SYMBOLS 2CH (button/indicator) wa 1 (22, 24, 27) ?/1 (power) (14, 19, 27, 28, 35, 48) ALPHABETICAL ORDER A L (22 24) CD 9 (20) DIMMER 3 (21) DISPLAY 2 (21, 31, 46) Display qa (21)

33、DVD 7 (20) ENTER qg (33, 35) FM MODE wf (29) INPUT MODE qd (20) IR (receptor) 4 (36, 46) 3145 6 7 8 9 q; qaqs qfqgqhqjqkqlw;wawswdwfwgwh SURROUND (button/indicator) w; (EXCEPT US, Canadian model) (US, Canadian model) A. F. D (button/indicator) w; 6 STR-DE495P/K750P SECTION 2 TEST MODE FACTORY PRESET

34、 MODE * All preset contents are reset to the default setting. * Procedure: While depressing the FM MODE and the PRESET TUNING buttons simultaneously, press the ?/1 button again. The message “FACTORY” appears and the present contents are reset to the default values. AM CHANNEL STEP 9 KHZ/10 KHZ SELEC

35、TION MODE * Either the 9 kHz step or 10 kHz step can be selected for the AM channel step. * Procedure: Set the FUNCTION to AM. Turn off the main power. While depressing the TUNING+ button or the PRESET TUNING + button, press the ?/1 button to turn on the main power. Either the message “9 k STEP” or

36、“10 k STEP” appears. Select the desired step. * For US/Canadian/E model only SPEAKER SIZE SELECTION MODE *Either Normal Speaker or Micro Satellite Speaker can be selected. *Procedure: While depressing the MAIN MENU button, press the ?/1 button to turn the main power. Either the message “NORM. SP.” o

37、r “MICRO SP.” is displayed. Select the desired speaker size. FLUORESCENT INDICATOR TUBE TEST MODE * All fluorescent segments are tested. When this test is activated, all segments turn on at the same time, then each segment turns on one after another. * Procedure: While depressing the FM MODE and the

38、 MD/TAPE buttons simultaneously, press the ?/1 button to turn on the main power. 1.All segments turn on. 2CH , SURROUND *1), MOVIE and MUSIC LED turn on. 2.Press the VIDEO button, confirm display. 2CH and MOVIE LED turn on. 3.Press the VIDEO button, confirm display SURROUND *1) and MUSIC LED turn on

39、. SW C SSB SLEEP L F E DIGITAL OPTMULTI CH IN 2 PROLOGICDTSSPMPEGAAC STEREORDS DDDD MHz k m SW L SL CR SSB SR SLEEP L F E DIGITALEX OPTCOAX MULTI CH IN 12 PROLOGIC IIDTS-ESNEO : 6SPBSPASPMPEG-2 AAC STEREO MONORDS MEMORY EQD.RANGE DDDD dB kHz mft. MHz L SL R SR EX COAX1 II-ES NEO : 6SPBSPA-2 MONO MEM

40、ORY EQD.RANGE dB Hz ft. 4.Press the VIDEO1 button, All segments and all LEDS turn off. 5.Every pressing of the VIDEO1 button turns on each segment and LED one after another in the same order. (Not only the VIDEO1 button, but also the other buttons such as VIDEO2 , DVD , MD/TAPE , CD and TUNER FM/AM

41、can be used.) SOUND FIELD CLEAR MODE * The preset sound field is cleared when this mode is activated. Use this mode before returning the product to clients upon completion of repair. * Procedure: While depressing the 2CH button, press the ?/1 button to turn on the main power. The message “SF. CLR.”

42、appears and initialization is performed. SOFTWARE VERSION DISPLAY MODE * The software version is displayed. * Procedure: While depressing the FM MODE and the DVD buttons simultaneously, press the ?/1 button to turn on the main power. The model name, destination and the software version are displayed

43、. KEY CHECK MODE * Button check * Procedure: While depressing the MUSIC and the TUNING buttons simultaneously, press the power ?/1 button to turn on the main power. “REST 25” appears. Every pressing of any button other than ?/1 counts down the buttons. The buttons which are already counted once are

44、not counted again. When all buttons are pressed “REST 00” appears. AUTOBETICAL MODE * This mode is installed in the Europe models only. When this mode is used, the receiver scans the broadcasts that can be received by the tuner, and sets up the broadcasts. Be sure to start scanning after connecting

45、the antenna. * Procedure: 1.Check that the antenna is connected. 2.Press the ?/1 button to turn on the power while pressing the MEMORY button. 3.The message appears and the receiver starts scanning. COMMAND MODE SELECTION MODE * The command mode (AV1 or AV2) of the remote commander can be selected.

46、* Procedure: 1.While depressing the ENTER button, press the ?/1 button to turn on the main power. 2.The message “C.MODE.AV 1” or “C.MODE.AV 2” appears for a moment. Select the desired mode. *1) A. F. D is used in US and Canadian models. 77 STR-DE495P/K750P Waveform DIGITAL Board For schematic diagra

47、ms. Note: All capacitors are in F unless otherwise noted. p : pF. 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in and 1/4 W or less unless otherwise specified. %: indicates tolerance. f: internal component. 2 : nonflammable resistor. 5 : fusible resistor.

48、 C : panel designation. A : B+ Line. B : B Line. Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. No mark : FM Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal produc- tion tolerances. Waveforms are taken wi

49、th a oscilloscope. Circled numbers refer to waveforms. Signal path. F: FM J: CD (ANALOG) c: DVD (DIGITAL) Abbreviation CND: Canadian model SP: Singapore model (Malaysia model included) AUS: Australian model THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this necessary note is printed in each block.) Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Note: Le