Onkyo-DVCP500-cd-sm维修电路原理图.pdf
《Onkyo-DVCP500-cd-sm维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《Onkyo-DVCP500-cd-sm维修电路原理图.pdf(69页珍藏版)》请在收音机爱好者资料库上搜索。
1、DV-CP500 SERVICE MANUALSERVICE MANUAL DVD CHANGER Black model MODEL DV-CP500 120V AC, 60HzBMDD Ref. No. 3734 072002 SAFETY-RELATED COMPONENT WARNING! THE MARK FOUND ON SOME COMPONENT PARTS INDICATES THE CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK. WHEN REPLACING, BE SURE TO USE PARTS OF IDENTICAL D
2、ESIGNATION. MAKE LEAKAGE-CURRENT OR RESISTANCE MEASUREMENTS TO DETERMINE THAT EXPOSED PARTS ARE ACCEPTABLY INSULATED FROM THE SUPPLY CIRCUIT BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER. RadioFans.CN 收音机爱 好者资料库 DV-CP500 SPECIFICATIONS Specifications and features are subject to change without notic
3、e. DVD Changer Power supplyAC 120 V, 60 Hz Power consumption20 W Weight15.4 lbs External dimensions17 1/8 x 5 1/16 x 16 15/16 (W/H/D) Signal systemNTSC Frequency range (digital audio)48 kHz sampling 4 Hz to 22 kHz 96 kHz sampling 4 Hz to 42 kHz Signal-to-noise ratio (digital audio)More than 90 dB Au
4、dio dynamic range (digital audio)More than 95 dB Harmonic distortion (digital audio)Less than 0.005 % Wow and flutterBelow measurable level Operating conditionsTemperature: 5 C to 35 C (41 F to 95 F), Operation status: Horizontal Outputs Video output1.0 V (p-p), 75 ohm , ne gative sync., pin jack 1
5、S-video output(Y) 1.0 V (p-p), 75 ohm , negative sync. (C) 0.286 V (p-p), 75 ohm , Mini DIN 4-pin 1 Component video output(Y) 1.0 V (p-p), 75 ohm , negative sync., pin jack 1 (PB)/(PR) 0.7 V (p-p), 75 ohm, pin jack 2 Audio output (digital output Optical)Optical connecter 1 Audio output (digital outp
6、ut Coaxial)0.5 V (p-p), 75 ohm , pin jack 1 Audio output (analog output)2.0 V (rms), 320 ohm , pin jack (L, R) 2 X X X X X X X RadioFans.CN 收音机爱 好者资料库 DV-CP500 SERVICE PROCEDURE 1. Replacing the fuses2. Safety-check out (Only U.S.A. model) After correcting the original service problem perform the fo
7、llowing safety check before releasing the set to the customer Connect the insulating-resistance tester between the plug of power supply cord and terminal GND on the back panel. Specifications: More than 10M ohm at 500V REF.NO.PART NO.DESCRIPTION F1 SR-5, T 2A250VCA T 2.0A This symbol located near th
8、e fuse indicates that the fuse used is show operating type, For continued protection against fire hazard, replace with same type fuse , For fuse rating, refer to the marking adjust to the symbol. Ce symbole indique que le fusible utilise est e lent. Pour une protection permanente, nutiliser que des
9、fusibles de meme type. Ce demier est indique la qu le present symbol est apposre. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL
10、ONLY. TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. POUR EVITER LES CHOCS ELECTRIQUE, INTRODUIRE LA LAME LA PLUS LARGE DA LA FICHE DANS LA BORNE CORRESPONDANTE DA LA PRISE ET POUSSER JUSQU AU FOND. WARNING : CAUTION : ATTENTION : The lightning flash with arrowhead s
11、ymbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended
12、to alert the user to the presence of important operating and maintenance (servicing) instruction in the literature accompanying the appliance. 1. Ground for the work-desk. Place a conductive sheet such as a sheet of copper (with impedance lower than 10M ohm) on the work-desk and place the set on the
13、 conductive sheet so that the chassis. 2. Grounding for the test equipments and tools. Test equipments and toolings should be grounded in order that their ground level is the same the ground of the power source. 3. Grounding for the human body. Be sure to put on a wrist-strap for grounding whose oth
14、er end is grounded. Be particularly careful when the workers wear synthetic fiber clothes, or air is dry. 4. Select a soldering iron that permits no leakage and have the tip of the iron well-grounded. 5. Do not check the laser diode terminals with the probe of a circuit tester or oscilloscope. PRECA
15、UTIONS LASER CAUTION Initialization of setup 1. Press the CD PLAY and DISC 3 key to the same timing on the front panel. You will see that the program is updated by watching the version in the FL tube. 2. Push the power switch. DV-CP500 EXPLODED VIEW Chassis A 1 2 3 4 5 BCDEFGH S2 S1 S1 S2 S2 S2 44 S
16、2 S2 41 42 S1 S1 40 28 9 S2 39 43 23 S3 S6 S3 S2 30 24 S2 23 26 29 17 24 S2 21 S2 20 19 15 16 18 23 23 22 10 13 8 7 S5 S4 5 S2 2 3 4 14 1 S5 24 FLFL 25 25 25 27 49 51 51 50 52 S4 S4 11 53 S2 S2 S2S2 S2 S6 S2 38 37 36 46 (19) 12 54 4847 DV-CP500 EXPLODED VIEW-2 DVD Mechanism A 1 2 3 4 5 BCD 260 70 25
17、0 300 P406 300 530 550 490 460 * 4 450 * 4 210 290 480 320 310 300 * 2 500 430 280 * 2 270 * 2 190 240 220 240 200 280 70 420 80 230 60 160 150 170 160150 160 150 50 280 140 240 160 150 160 150 100 120 130 470 510 50 CLAMPER DVD ASSY BASE ASSY - CDM5G 90 110 440 520 *2 Part No. 55542660 Part No.5554
18、2650 300 560300 300 300 5000 Assy Part No. 55542660 DV-CP500 BLOCK DIAGRAM-0 OVERALL A 1 2 3 4 5 BCDEFGH DV-CP500 BLOCK DIAGRAM - 1 MAIN CIRCUIT BOARD A 1 2 3 4 BCDE To Mechanism control To Pick up To Display To OUT To OUT CP25:04PIN CP25:06PIN CN27:SPDIF To OUT CP25:08PIN CP25:10PIN CP25:12PIN CP25
19、:14PIN CP25:16PIN CP25:18PIN TR SWITCH CIRCUIT P SCAN ON/OFF IC MEMFLASH M29W800A T901N1 IC41 IC31 IC-DRAM HY57V651620BTC-8 125M 64M(1M x 16 x 4) IC- VIDEOPROC STI5519 MPEG VIDEO DECODER IC-LOGIC 74HC74 FLIF/FLOP CMOS IC-LOGIC 74HC86 GATE HCMOS INVERTER HCT IC-LOGIC M74HCU04M1R IC-OPEAMP BA4560F IC6
20、1 IC-CONV WN8728 D/A POWER SUPPLY UNIT DV-CP500 BLOCK DIAGRAM - 2 DISPLAY SECTION A 1 2 3 4 BCDE From Power supply unit To Main PC board Key matrix DV-CP500 BLOCK DIAGRAM - 3 DVD MECHANISM SINGLE BIT ADDRESSABLEI/O 75PG14-BIT IN/OUTPUT PORT;SINGLE BIT ADDRESSABLEI/O 76PG24-BIT IN/OUTPUT PORT;SINGLE
21、BIT ADDRESSABLEI/O 77PG34-BIT IN/OUTPUT PORT;SINGLE BIT ADDRESSABLEI/O 78PE0/EC0/INT0INPUT FOR EXTERNAL INTERRUPT REQUEST.I 79PE1/EC1/INT1INPUT FOR EXTERNAL INTERRUPT REQUEST.I 80PE2/IN2INPUT FOR EXTERNAL INTERRUPT REQUEST.I PIN NUMBER PIN NAMEMAIN FUNCTION IN/OU T REMARK DV-CP500 INPUTOUTPUT 1PIOs
22、and communicationPIO25PIO25-I/O 2PIOs and communicationPIO26PIO26-I/O 3PIOs and communicationPIO27PIO27-I/O 4-VDD3_33.3V POWER SUPPLY-POWER 5-VSSGROUND-POWER 6PIOs and communicationPIO30PIO30PARA_DATA0-I/O 7PIOs and communicationPIO31PIO31PARA_DATA1-I/O 8PIOs and communicationPIO32PIO32PARA_DATA2-I/
23、O 9PIOs and communicationPIO33PIO33PARA_DATA3-I/O 10PIOs and communicationPIO34PIO34CAPTURE_IN1 PARA_DATA4UART1 RTS(RTS1)I/O 11PIOs and communicationPIO35PIO35CAPTURE_IN2 PARA_DATA5UART2 RTS(RTS2)I/O 12PIOs and communicationPIO36PIO36PARA_DATA6 UART1 CTS(CTS1) COMP_OUT1I/O 13PIOs and communicationPI
24、O37PIO37PARA_DATA7 UART1 CTS(CTS2) COMP_OUT0I/O 14-VDD2_52.5V POWER SUPPLY-POWER 15-VSSGROUND-POWER 16Front-endB_DATAI2S DATASER_DATA-I 17Front-endB_BCLKI2C BIT CLOCKSER_BCLK-I 18Front-endB_FLAGI2S ERROR FLAG DVDSER_VALID-I 19Front-endB_SYNCI2S SECTOR/ABS TIMESER_SYNC-I B_WCLK-I/O 21RESERVEDRESERVED
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Onkyo DVCP500 cd sm 维修 电路 原理图