JBL-E150P-pwr-sm维修电路原理图.pdf

上传人：cc518

文档编号：104594

上传时间：2020-11-07

格式：PDF

页数：28

大小：2.40MB

《JBL-E150P-pwr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《JBL-E150P-pwr-sm维修电路原理图.pdf（28页珍藏版）》请在收音机爱好者资料库上搜索。

1、 Northridge E-Series E150P Powered Subwoofer Service Manual JBL Consumer Products 250 Crossways Park Dr. Woodbury, New York 11797 Rev2 2/2004 RadioFans.CN 收音机爱好者资料库 - CONTENTS - BASIC SPECIFICATIONS .1 SAFETY INFORMATION .2 DETAILED SPECIFICATIONS .3 CONNECTIONS.4 OPERATION .7 BASIC TROUBLESHOOTING

2、.8 EXPLODED VIEW/PARTS LIST.9 TEST SET-UP AND PROCEDURE.10 AMPLIFIER BLOCK DIAGRAM.11 TECH TIP JBLTT2003-04 .12 DETAILED TROUBLESHOOTING. 13 P.C.B. DRAWINGS.16 ELECTRICAL PARTS LIST .20 IC/TRANSISTOR PINOUTS.24 SCHEMATICS.25 PACKING.27 E150P SPECIFICATIONS Amplifier Power (RMS): 150 Watts Peak Dynam

3、ic Power *: 250 Watts Driver: 10 (254mm) PolyPlas Inputs: Line Level (switchable to LFE) and Speaker Level with 5-way binding posts Low-Pass Frequency: Variable from 50Hz to 150Hz Frequency Response: 27Hz Low-pass crossover setting Dimensions (H x W x D): 17-3/4 x 12-1/4 x 14-1/2 (451mm x 311mm x 36

4、8mm) Weight: 33.5 lb/15.2kg JBL continually strives to update and improve existing products, as well as create new ones. The specifications and details in this and related JBL publications are therefore subject to change without notice. * The Peak Dynamic Power is measured by recording the highest c

5、enter-to-peak voltage measured across the output of a resistive load equal to minimum impedance of the transducer, using a 50Hz sine wave burst, 3 cycles on, 17 cycles off. E150P E150P 1 RadioFans.CN 收音机爱好者资料库 Warning Any person performing service of this unit will be exposed to hazardous voltages

6、and the risk of electric shock. It is assumed that any person who removes the amplifier from this cabinet has been properly trained in protecting against avoidable injury and shock. Therefore, any service procedures are to be performed by qualified service personal ONLY! Caution Early revisions of t

7、he unit did not have a power switch. Hazardous voltages are resent within the unit whenever it is plugged in. Before amplifier is plugged in, be sure its rated voltage corresponds to the voltage of the AC power source to be used. Incorrect voltage could cause damage to the amplifier when the AC powe

8、r cord is plugged in. Do not exceed rated voltage by more than 10%: operation below 90% of rated voltage will cause poor performance or may shut the unit off. Leakage/Resistance Check Before returning the unit to the customer, perform a leakage or resistance test as follows: Leakage Current. Note th

9、ere is no power switch on early revisions of this unit. When the power plug is plugged in, the unit is live. Connect the unit to its rated power source. Using an ammeter, measure the current between the neutral side of the AC supply and chassis ground of the unit under test. If leakage current excee

10、ds 0.5mA, the unit is defective. Reverse the polarity of the AC supply and repeat. Resistance. Measure the resistance from either side of the line cord to chassis ground, If it is less than 500k ohms, the unit is defective. WARNING! DO NOT return the unit to the customer if it fails one of these tes

11、ts until the problem is located and corrected. Critical Components All components identified with the IEC symbol in the parts list and schematic diagram designate components in which safety can be of special significance when replacing identified with. Use only the replacement parts designated in th

12、e parts list or parts with the same rating of resistance, wattage or voltage. SAFETY INFORMATION List of Safety Components Requiring Exact Replacements Part Number/ Designator Description F1 093-205209-300 Line Fuse Slo Blo 1.25A 5x20mm 083-041802-009 250V UL approved SPT-2 or better with polarized

13、plug, UL approved wired with the hot side to fused side. Use with factory replacement panel strain relief (70305) only. PT1 042-010052-003 Power Transformer. Use only factory replacement. BR1 052-400080-000 Bridge diode. Use only factory replacement. C6,8 034-470745-200 4700uF 50V electrolytic filte

14、r caps. Be sure replacement part is at least the same working voltage and capacitance rating. Also the lead spacing is important. Incorrect spacing may cause premature failure due to internal cabinet pressure and vibration. 063-531808-000 Rear Amp Cover Use only factory replacement Inductor 043-5602

15、00-000 L1 - Use only factory replacement Inductor 043-300101-000 L2 - Use only factory replacement Inductor 043-700101-000 L3 - Use only factory replacement Inductor 043-324300-000 L4 - Use only factory replacement E150P 2 JBL E150P Powered Sub/ Plate Amp LINE VOLTAGEYes/NoHi/Lo LineNom.UnitNotes US

16、 120vac/60HzYes108-132120VrmsNormal Operation EU 230vac/50-60HzYes207-264230VrmsNormal operation, MOMS required ParameterSpecificationUnit QA Test LimitsConditionsNotes Amp Section Type (Class AB, D, other)Dn/an/aClass D Preferred.Sink required for Class AB Load Impedance (speaker)4Ohmsn/aNominalZ-c

17、urve required Rated Output Power75Watts701 input driven AVG RMS Dynamic Power150Watts135 Average RMS power, 3/20 Cycles 50 Hz, Driven 6dB above its input sensitivity sensitivity THD Rated Power0.3%122k filter75 Watts THD 1 Watt0.1%0.522k filter DC Offset10mV-DC30 Speaker Outputs Damping factor50DF35

18、Measured at amplifier board Measured at the amplifier board THD 4.7Kohmsn/aNominal Filters Speaker in LP 2nd order varia60-150 Hz 10 Subsonic filter (HPF) fixed 6thFixed LFE Low pass 2nd order fixed200LP T T 1M (NO LOAD) Resistance from V+ (C6 P+) to V- (C8 P-) gradually Fully CHARGED should read 10

19、k Resistance from V+ (C6 P+) to S+ (SPK O/P) should read 1M Resistance from V- (C8 P-) to S+ (SPK O/P) should read 1M 2. Power UpLED RED With a 5mV signal to Low level input, LED should change to GREEN -Voltage measurements (DVM) OP AMP LEDP-U4(1)P-U4(7) RED0Vrms8VDC GREEN6.3Vrms-10.7VDC 3. D.C. Ope

20、ration -Voltage measurements (DVM) on CLASS D POWER AMP BetweenV+Q4(E)Q1(C)Q10(C)U7(1)U7(2)U7(4)U7(6)U7(7)U7(8) And This Point GNDV-GNDGNDGNDGNDGNDGNDGNDGND Get this Reading 45.9V0V-45.9V0V-45.9V-45.7V-45.5V0V0V4.7V 4. Check Switching Frequency Oscilloscope - USE THE PROBE TIP TO U6(7) TO GND Readin

21、g 100kHz +/-10%,22Vp-p B. Pre Amp Section Line Level Input Sensitivity -Set upTurn level, XOVER FREQ POT Fully CW and LFE switch off Generator Set at 100mV50Hz Signal to Line level input E150P E150P DETAILED TROUBLESHOOTING 13 - Voltage measurements OP AMP U2(1)U2(14)U2(8)U3(7)U3(1)U3(14)U3(8)U5(7)U

22、5(1) SPEAKER O/P 133.6mV200.2mV245.9mV314.8mV314.9mV350mV1.67V1.452V2.098V15.3V 2. High Level Input Sensitivity -Set upTurn level, XOVER FREQ POT Fully CW and LFE switch off Set Generator at 1.15V50Hz Signal to High level input -Voltage measurements 15.3V at speaker output 3. Low-Pass -Set upSet Gen

23、erator at 100 mV100Hz Signal to Line level input Measure voltage at S+ speaker output -Voltage measurement XOVER FREQ. SettingOutput CW10.72V CCW2.165V 4. LFE -Set upSet Generator at 100mV200Hz Signal to Line level input Measure voltage at S+ speaker output LFE switch SettingOutput Normal2.9V LFE7.6

24、2V See flow chart next page for diagnostics. E150P E150P DETAILED TROUBLESHOOTING (CONTD) 14 CAUTION : SPEAKER OUTPUT IS FLOATING AND IS NOT PROTECTED AGAINST A SHORT TO GROUND. ALL TEST INSTRUMENTS CONNECTED TO THE OUTPUT MUST BE FLOATING. ATTACH THE SCOPE PROBE TIP TO S - and REFERENCE LEAD TO S+.

25、 (A 10mV signal may need from the input to trigger the Switch turn on) no no yes yes no no yes yes no no yes yes no no yes yes START Check +/- 15V- MOD +/- 15V voltage at U 6(8),U6(4) Discharge C37, Check fuse transformer, L4, rectifier, C6 and C8 Use scope to check switching frequency U6(7) 100KHz

26、+/- 10% , 22Vp- p Check Q4(E) TO V- = 0V D.C. Power up with no signal input LED RED OK OK OK OK OK OK OK OK Check MUTE(+8V) and Q24,Q25,Q26 Use scope to check O/P U7(6) and GND 90Vp- p square wave shown Check L2,L3,C71,C72, C73,C74 I/P:10mv/50HZ Check +15V/SW Q4(E) TO V- 15V Replace Q18,Q22 CLASS D

27、AMP OK END Check U7,Q16,Q17, Q20,Q21,R87, D26,D35,C64 Check FB1,FB2,C45, C50,C60,C63, R81,R82 Check U7(1) = - 33V Check MUTE(- 10.7V), And Q24,Q25,Q26 Resistance check (no load) between V+ V- , V+ O/P,V- O/P and O/P to GND is 10K E150P E150P DETAILED TROUBLESHOOTING (CONTD) FLOW CHART 15 E150P E150P

28、 16 E150P E150P 17 E150P E150P 18 E150P E150P 19 E150P Electrical Parts List Part NumberDescriptionReference DesignatorQty Resistors 020-000498-120Carbon Film0R 1/4W J R10,112 021-100401-120MOF Resistor1K 1W JR1031 021-820303-020MOF Resistor820R 3WS J 8x20R6,92 022-500003-020KNP Resistor0R05 3WS J F

29、K TYPER1041 024-100298-120SMD Resistor10R 1/8W J 0805 R81,822 024-100398-120SMD Resistor100R 1/8W J 0805 R621 024-100498-120SMD Resistor1K 1/8W J 0805 65,79,83,92,95,96,105,1088 024-100598-120SMD Resistor10K 1/8W J 0805 R2,37,54,58,63,69,71,72,749 024-100698-120SMD Resistor100K 1/8W J 0805 R3,112,22

30、-256 024-110598-100SMD Resistor11K 1/8W F 0805 R981 024-113598-100SMD Resistor11K3 1/8W F 0805 R341 024-120498-120SMD Resistor1K2 1/8W J 0805 R51,532 024-130498-100SMD Resistor1K3 1/8W F 0805 R35,1102 024-137598-120SMD Resistor13K7 1/8W F 0805 R42,432 024-137698-100SMD Resistor137K 1/8W F 0805 R321

31、024-150498-120SMD Resistor1K5 1/8W J 0805 R67,68,12-156 024-150598-120SMD Resistor15K 1/8W J 0805 R291 024-200598-120SMD Resistor20K 1/8W J 0805 R941 024-220398-120SMD Resistor220R 1/8W J 0805 R901 024-220498-121SMD Resistor2K2 1/8W J 0805 R1,87,613 024-220598-120SMD Resistor22K 1/8W J 0805 R50,52,1

32、183 024-220798-120SMD Resistor2M2 1/8W J 0805 R80,1212 024-237598-120SMD Resistor23K7 1/8W F 0805 R481 024-237698-100SMD Resistor237K 1/8W F 0805 R451 024-243698-100SMD Resistor243K 1/8W F 0805 R361 024-270498-120SMD Resistor2K7 1/8W J 0805 R64,732 024-300398-120SMD Resistor300R 1/8W J 0805 R551 024

33、-300598-120SMD Resistor30K 1/8W J 0805 R561 024-330498-120SMD Resistor3K3 1/8W J 0805 R7,8,593 024-330598-120SMD Resistor33K 1/8W J 0805 R4,5,1223 024-332498-100SMD Resistor3K32 1/8W F 0805 R26,272 024-360498-120SMD Resistor3K6 1/8W J 0805 R281 024-390498-120SMD Resistor3K9 1/8W J 0805 R931 024-3905

34、98-120SMD Resistor39K 1/8W J 0805 R771 024-430498-100SMD Resistor4K3 1/8W F 0805 R781 024-453598-100SMD Resistor45K3 1/8W F 0805 R301 024-470298-120SMD Resistor47R 1/8W J 0805 R101,1022 024-470398-120SMD Resistor470R 1/8W J 0805 R76,99,1003 024-470498-120SMD Resistor4K7 1/8W J 0805 R85,862 024-47059

35、8-120SMD Resistor47K 1/8W J 0805 R44,47,49,1074 024-470698-120SMD Resistor470K 1/8W J 0805 R701 E150P E150P 20 Part NumberDescriptionReference DesignatorQty 024-470798-120SMD Resistor4M7 1/8W J 0805 R601 024-560498-120SMD Resistor5K6 1/8W J 0805 R40,412 024-604598-100SMD Resistor60K4 1/8W F 0805 R39

36、1 024-620398-120SMD Resistor620R 1/8W J 0805 R16,18,573 024-680498-120SMD Resistor6K8 1/8W J 0805 R46,912 024-680598-120SMD Resistor68K 1/8W J 0805 R31,33,663 024-909498-100SMD Resistor9K09 1/8W F 0805 R381 025-010300-000ThermisterTSE-103 K L:50mm1 026-200595-269Freq Pot 20KPN:RD163121R03D-20KBx2(EJ

37、)VR21 026-500495-252Level Pot 5KPN:RK163111R52B-5KA (EJ)VR11 Capacitors 031-100244-100Ceramic Capacitor0u01/50V K 0805 X7R C5,10,33,45,51,66,677 031-100343-100SMD Capacitor100pF/50V J 0805 NPO C36,58,163 031-100344-100SMD Capacitor0u1/50V K 0805 X7R C11,42-44,46-49,52,54,55,60,63,71,74,7716 031-1003

38、84-100R SMD Capacitor0u1/250V K 1206 X7R C3,72 031-150244-100SMD Capacitor0u0015/50V K 0805 X7R C321 031-220344-100SMD Capacitor220pF/50V J 0805 NPO C20,21,19,14,155 031-330444-300SMD Capacitor3300pF/50V K 0805 X7R C40,342 031-470244-102SMD Capacitor0u047/50V K 0805 X7R C62,592 031-560243-100SMD Cap

39、acitor56pF/50V J 0805 NPO C57,612 031-560343-102SMD Capacitor560pF/50V J 0805 NPO C561 032-100464-202Mylar Capacitor1uF/100V K P:10C70,70B2 033-470444-270NPE Capacitor4u7/50V K10 (R)8x13 SBEC731 033-680464-270NPE Capacitor6u8/100V K10 (R)1020 GNEC721 034-100525-300Electrolytic Capacitor10uF/25V M (R

40、)0511 P:5 C351 034-100625-300Electrolytic Capacitor100uF/25V M (R)6.3x11 P:5C641 034-220525-301Electrolytic Capacitor22uF/25V M (R)5x11 P:5 C39,50,53,41,4,96 034-220615-301Electrolytic Capacitor220uF/16V M (R)0611 P:5C371 034-330525-300Electrolytic Capacitor33uF/25V M (R)0511 P:5C11 034-330615-300El

41、ectrolytic Capacitor330uF/16V M (R)0812 P:5 C12,782 034-470415-301Electrolytic Capacitor4u7/50V M (R)0511 P:5 C21 034-470615-301Electrolytic Capacitor470uF/16V M (R)0812 P:5 C651 034-470745-200Electrolytic Capacitor4700uF/50V M (R)2236C6,82 038-100363-300MPE Capacitor0u1/100V J C68,69,273 038-220393

42、-300MPE Capacitor0u22/63V J C25-26,29,314 038-330393-300MPE Capacitor0u33/63V J C22,23,243 038-470293-300MPE Capacitor0u047/63V J C28,302 039-100384-100Safety CapacitorHQX0.1K275VACx2 18x6x12mmCXAC11 Semiconductors 051-000600-100NPN TransistorPN:MPSW06RLRA TO-92 Q2,Q162 051-003100-000NPN TransistorP

43、N:TIP 31C TO-220 (MOSPEC)Q41 051-005600-100PNP TransistorPN:MPSW56RLRA TO-92 Q31 E150P E150P 21 Part NumberDescriptionReference DesignatorQty 051-222200-100NPN TransistorPN:MPS2222ARLRA TO-92 Q211 051-290700-100PNP TransistorPN:MPS2907A RLRA TO-92 Q19,232 051-540101-000PNP TransistorPN:2N5401 TO-92

44、Q11 051-555100-000NPN TransistorPN:2N5551 TO-92 Q171 051-640001-000MOSFET N-ChannelPN:IRF640N TO-220 (IR)Q18,222 052-400080-000Bridge RegulatorPN:RS804 400V,8ABR11 053-211100-000IC;DIP,DriverPN:IR2111 Half-Bridge DriverU71 054-000100-100SMD DIODEPN:ES1D 200V 1A D5,26,29,33,385 054-001002-100SMD ZENE

45、R DIODEPN:BZX84C10 10V SOT-23 D351 054-001501-100SMD ZENER DIODEPN:BZX84C15 15V SOT-23 D6,7,93 054-007200-100SMD IC; (Dual OP-Amp) PN:TL072CDR SO-8 U5,62 054-007400-100SMD IC;(Quad OP-Amp) PN:TL074CDR U2,32 054-011400-100SMD TransistorPN:DTC114TKA SMT3 Q71 054-033904-100SMD TransistorPN:MMBT3904LT1

46、SOT23 Q11,14,13,5,8,96 054-033906-100SMD TransistorPN:MMBT3906LT1 SOT23 Q6,10,12,154 054-045580-100SMD IC; (Dual OP=Amp) PN:NJM4558M-TE3 DMP-8 U41 054-050601-100SMD ZENER DIODEPN:BZX84C5V6 5.6V SOT-23 D24,36,373 054-414803-100SMD DIODEPN:LL4148 (Wishay)D1-4,8,10-23,27,3021 054-540100-100SMD TransistorPN:MMBT5401 LT1 SOT-23 Q20,24,263 054-555100-100SMD TransistorPN:MMBT5551 LT1 Q251 050-505200-001LEDPN:LT-2402-21D1B1 Miscellaneous 065