HarmanKardon-AVR2700-avr-sm维修电路原理图.pdf
《HarmanKardon-AVR2700-avr-sm维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《HarmanKardon-AVR2700-avr-sm维修电路原理图.pdf(158页珍藏版)》请在收音机爱好者资料库上搜索。
1、Service Manual harman/kardon AVR 2700 Audio/Video Receiver CONTENTS ESD WARNING.2 LEAKAGE TESTING.3 BASIC SPECIFICATIONS.4 FRONT PANEL CONTROLS.5 REAR PANEL CONNECTIONS.7 REMOTE CONTROL FUNCTIONS. 9 CONNECTIONS/INSTALLATION.14 OPERATION . . . . . .33 BASIC TROUBLESHOOTING.41 PROCESSOR RESET.42 AMPLI
2、FIER BIAS ADJUSTMENT.43 PACKAGING.44 DISASSEMBLY45 UNIT EXPLODED VIEW.46 BLOCK DIAGRAM.47 PCB DRAWINGS.49 ELECTRICAL PARTS LIST.69 SEMICONDUCTOR PINOUTS138 SCHEMATICS.139 WIRING DIAGRAM.158 harman/kardon Released 2012 8500 Balboa Blvd. Discontinued XXXX Northridge, CA. 91329 Rev0 12/2012 RadioFans.C
3、N 收音机爱 好者资料库 Eachprecautioninthismanualshouldbefollowedduringservicing. Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a component identified with , use only the replacement parts designated, or parts with the same ratings or resistance,
4、 wattage, or voltage that are designated in the parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably insulated from the supply circuit before retuming the product to the customer. Some semiconductor (solid state) devices ca
5、n be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and semiconductor chip components. The following techniques should be used to help reduce
6、the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available dis
7、charging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge build-
8、up or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can generate electrical charges sufficient to damage ES devices. 5. Do not use freon
9、-propelled chemicals. These can generate electrical change sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by
10、 conductive foam, aluminum foil or comparable conductive material.) 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. Be sure no power is applied
11、to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together or your clothes fabric or the lifting of your foot from a carpeted floor can generate static elect
12、ricity sufficient to damage an ES devices. CAUTION : AVR 2700 harman/kardon 2 RadioFans.CN 收音机爱 好者资料库 SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Measure leakage current to a known earth ground
13、(water pipe, conduit, etc.) by connecting a leakage current tester between the earth ground and all exposed metal parts of the appliance (input/output terminals, screwheads, metal overlays, control shaft, etc.). Plug the AC line cord of the appliance directly into a 120V AC 60Hz outlet and turn the
14、AC power switch on. Any current measured must not exceed o.5mA. ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER. Device under test Test all exposed metal surfaces Also test with plug
15、 reversed (Using AC adapter plug as required) AC Leakage Test Leakage current tester Reading should not be above 0.5mA Earth ground AVR 2700 harman/kardon 3 RadioFans.CN 收音机爱 好者资料库 Specifications Audio Section Stereo power:AVR 3700/AVR 370: 125W per channel, two channels driven 6/8 ohms, 20Hz 20kHz,
16、 0.07% THD AVR 2700/AVR 270: 105W per channel, two channels driven 6/8 ohms, 20Hz 20kHz, 0.07% THD Multichannel power:AVR 3700/AVR 370: 125W per channel, two channels driven 6/8 ohms, 20Hz 20kHz, 0.07% THD AVR 2700/AVR 270: 105W per channel, two channels driven 6/8 ohms, 20Hz 20kHz, 0.07% THD Input
17、sensitivity/impedance:250mV/27k ohms Signal-to-noise ratio (IHF-A):100dB Surround system adjacent channel separation: Dolby Pro Logic/DPLII: 40dB Dolby Digital: 55dB DTS: 55dB Frequency response ( 1W):10Hz 130kHz (+0dB/3dB) High instantaneous current capability (HCC): 42 amps (AVR 3700/AVR 370); 39
18、amps (AVR 2700/AVR 270) Transient intermodulation distortion (TIM): Unmeasurable Slew rate:40V/sec FM Tuner Section Frequency range:87.5 108.0MHz Usable sensitivity IHF:1.3V/13.2dBf Signal-to-noise ratio (mono/stereo):70dB/68dB Distortion (mono/stereo):0.2%/0.3% Stereo separation:40dB 1kHz Selectivi
19、ty (400kHz):70dB Image rejection:80dB IF rejection:80dB AM Tuner Section Frequency range:520 1710kHz (AVR 3700/AVR 2700) 522 1620kHz (AVR 370/AVR 270) Signal-to-noise ratio:38dB Usable sensitivity (loop):500V Distortion (1kHz, 50% mod):1.0% Selectivity (10kHz):30dB Video Section Television format:NT
20、SC (AVR 3700/AVR 2700); PAL (AVR 370/AVR 270) Input level/impedance:1Vp-p/75 ohms Output level/impedance:1Vp-p/75 ohms Video frequency response (composite video): 10Hz 8MHz (3dB) HDMI:Support up to 4k x 2k General Specifications Power requirement:120V AC/60Hz (AVR 3700/AVR 2700); 220V 240V AC/50Hz 6
21、0Hz (AVR 370/AVR 270) Power consumption: ADDR 00 01 10 11 0 x90 0 x92 0 x94 0 x96 OPEN OPEN OPEN 12.08.02 MULTI. LAB ANAM ISSUE PMP 11.12.2712.08.0211.12.27 W.Y.YL.J.HS.K.S HDMI6 2012.05.29 2012.05.292012.05.29 19 18 17 16 15 14 13 12 11 10 9 8 7 6 ? 4 3 2 1 JK1001 Q1005 T1P141C Q1006 T1N241C R1015
22、22K R1014 1K C1003 0.1uF / 16V R1013 47K R1018 1005 / 1/16W / 0ohm R1017 47K R1016 4.7K 19 18 17 16 15 14 13 12 11 10 9 8 7 6 ? 4 3 2 1 JK1002 Q1003 T1P141C Q1004 T1N241C R1009 22K R1008 1K C1002 0.1uF / 16V R1007 47K R1012 1005 / 1/16W / 0ohm R1011 47K R1010 4.7K 19 18 17 16 15 14 13 12 11 10 9 8 7
23、 6 ? 4 3 2 1 JK1003 Q1001 T1P141C Q1002 T1N241C R1003 22K R1002 1K C1001 0.1uF / 16V R1001 47K R1006 1005 / 1/16W / 0ohm R1005 47K R1004 4.7K C1013 10uF/6.3V C1014 0.1uF / 16V C1017 0.1uF / 16V L1001 9R005Z C1015 0.1uF / 16V C1016 0.1uF / 16V ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?
24、 32 31 30 29 28 27 26 25 24 23 22 21 20191817161514131211109876?4321 IC1001 ADV3002 C1018 0.1uF / 16V C1019 0.1uF / 16V C1020 50V/1000PF Q1009 CVTRT1N441C NC R1040 4.7Kohm_NC R1036 1005 / 1/16W / 0ohm R1037 1005 / 1/16W / 0ohm R1029 10Kohm R1028 10Kohm R1027 10Kohm R1026 2.2Kohm R1025 2.2Kohm R1035
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- HarmanKardon AVR2700 avr sm 维修 电路 原理图