HarmanKardon-AVR335-avr-sm维修电路原理图.pdf

《HarmanKardon-AVR335-avr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《HarmanKardon-AVR335-avr-sm维修电路原理图.pdf（127页珍藏版）》请在收音机爱好者资料库上搜索。

1、 harman/kardon AVR335 AVR335 7 X 55W 7.1 CHANNEL A/V RECEIVER SERVICE MANUAL CONTENTS ESD WARNING.2 LEAKAGE TESTING.3 BASIC SPECIFICATIONS.4 FRONT PANEL CONTROLS.5 REAR PANEL CONNECTIONS.7 REMOTE CONTROL FUNCTIONS.10 INSTALLATION/CONNECTIONS.13 OPERATION.15 TROUBLESHOOTING GUIDE.21 PROCESSOR RESET.2

2、1 UNIT EXPLODED VIEW.22 DISASSEMBLY23 AMP BIAS ADJUSTMENT.24 TECH TIP HKTT2003-01.25 BLOCK DIAGRAM.26 PCB DRAWINGS.27 ELECTRICAL PARTS LIST.34 SEMICONDUCTOR PINOUTS.77 SCHEMATICS119 WIRING DIAGRAM.126 PACKAGING.127 harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev1 5/2005 www.f

3、reeservicemanuals.infoIts Free www.freeservicemanuals.info RadioFans.CN 收音机爱 好者资料库 Eachprecautioninthismanualshouldbefollowedduringservicing. Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a component identified with , use only the repla

4、cement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably insulated from the supply circuit before retuming th

5、e product to the customer. Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and semiconductor ch

6、ip components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known ear

7、th ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive

8、 surface such as aluminum foil, to prevent electrostatic charge build-up or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can generate e

9、lectrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replaceme

10、nt ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.) 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly

11、 into which the device will be installed. Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together or your clothes fabric or th

12、e lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices. CAUTION : AVR335 AVR335 harman/kardon www.freeservicemanuals.infoIts Free www.freeservicemanuals.info RadioFans.CN 收音机爱 好者资料库 2 SAFETY PRECAUTIONS The following check should be performed

13、for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Measure leakage current to a known earth ground (water pipe, conduit, etc.) by connecting a leakage current tester between the earth ground and all exposed metal parts of the appliance (input/output terminals,

14、 screwheads, metal overlays, control shaft, etc.). Plug the AC line cord of the appliance directly into a 120V AC 60Hz outlet and turn the AC power switch on. Any current measured must not exceed o.5mA. ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL SHOCK HAZARD

15、AND MUST BE CORRECTED BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER. Device under test Test all exposed metal surfaces Also test with plug reversed (Using AC adapter plug as required) AC Leakage Test Leakage current tester Reading should not be above 0.5mA Earth ground AVR335 AVR335 harman/kardon w

16、ww.freeservicemanuals.infoIts Free www.freeservicemanuals.info RadioFans.CN 收音机爱 好者资料库 AVR 335 TECHNICAL SPECIFICATIONS Audio Section Stereo Mode Continuous Average Power (FTC) 70 Watts per channel, 20Hz20kHz, 0.07% THD, both channels driven into 8 ohms Seven-Channel Surround Modes Power per Individ

17、ual Channel Front L press it again to turn the unit off.The Power Indicator 3 turns blue when the unit is on. 4 Headphone Jack: This jack may be used to listen to the AVR 335s output through a pair of headphones. The speakers will automatically be turned off when the headphone jack is in use.When co

18、nfiguring your sys- tem using EzSet+, the calibration microphone should be plugged into this jack using the supplied adaptor that converts the small mini-plug at the end of the microphones cord to a 1/4 plug. 5 Tone Mode: Pressing this button enables or dis- ables the Bass and Treble tone controls.W

19、hen the but- ton is pressed so that TONE IN appears in the Lower Display Line , the Bass and Treble controls may be used to adjust the output signals. When the button is pressed once or twice so that the words TONE OUT appear in the Lower Display Line , the output signal will be “flat, ” no matter h

20、ow the actual Bass and Treble Controls are adjusted. 6 Speaker Select Button: Press this button to begin the process of configuring the unit to match the type of speakers used in your listening room. (See pages 2224 for more information on speaker setup and configuration.) 7 Surround Mode Group Sele

21、ctor: Press this but- ton to select the top-level group of surround modes. Each press of the button will select the current or last used mode in each of the surround mode groups (e.g., Dolby, DTS, DTS Neo:6, Logic 7, DSP, Stereo). When the button is pressed so that the name of the desired surround m

22、ode group appears in the on- screen display and in the Lower Display Line , press the Surround Mode Selector 8 to cycle through the individual modes available. For example, press this button to select Dolby modes, and then press the Surround Mode Selector 8 to choose from the various mode options. 1

23、 Main Power Switch 2 Power Indicator 3 Standby/On Switch 4 Headphone Jack 5 Tone Mode 6 Speaker Selector 7 Surround Mode Group Selector 8 Surround Mode Selector 9 Tuning Selector )/Buttons ! Tuner Band Selector Set Button # Digital Input Selector $ Preset Station Selector % Delay Adjust Selector Inp

24、ut Source Selector the Sleep indicator numbers will disappear and the words SLEEP OFF will appear in the Lower Display Line . When you will be away from home for an extended period of time, it is always a good idea to completely turn the unit off with the front-panel Main Power Switch 1. NOTE: All p

25、reset memories are lost if the unit is left turned off by using the Main Power Switch 1 for more than four weeks. Source Selection To select a source, press any of the Input Selector Buttons egon the remote. The input source may also be changed by pressing the front-panel Input Source Selector Butto

26、n . Each press of the button will move the input selec- tion through the list of available inputs. As the input is changed, the AVR 335 will automati- cally switch to the digital input (if selected), surround mode, speaker configuration, output levels, crossover frequency and night mode status that

27、were entered during the configuration process for that source. The front-panel Video 4 Inputs , Optical 3 Digital Input * or the Coaxial 3 Digital Input ( may be used to connect a device such as a video game or camcorder to your home entertainment system on a temporary basis. As the input source is

28、changed, the new input name will appear momentarily as an on-screen display in the lower third of the video display.The input name will also appear in the Upper Display Line and in the front-panel Input Indicators . When an audio source is selected, the last video input used remains routed to the Vi

29、deo 1/Video 2 Video Outputs hkandVideo and S-Video Monitor Outputs c.This permits simultaneous viewing and listening to different sources.This also allows you to choose a video source and then select the 6/8-Channel Direct Inputs j as the audio source. When a composite or S-video source is selected,

30、the video signal for that input will be routed to the S-Video Monitor Outputcand will be viewable on a TV monitor connected to the AVR 335. 6-Channel/8-Channel Direct Input There are two input choices available for use with sources such as a DVD-Audio or SACD player that are connected to the 6/8-Cha

31、nnel Direct Inputs j. Select the appropriate input according to how your system and source equipment are configured: I6 CH DIRECT should be used when the SBR and SBL inputs j are NOT in use.The AVR presumes that the input source device has its own internal bass management system.This input passes th

32、e input from the source directly through to the volume control without any analog to digital conversion and it mutes the unused input jacks to prevent unwanted noise from interfering with system performance. I8 CH DIRECT should be used when an input is connected to all eight 8-Channel Direct Inputs

33、j.The AVR operates on the assumption that the input source device has its own internal bass management system.This input passes the input from the source directly through to the vol- ume control without any analog-to-digital conver- sion and it mutes the unused input jacks to pre- vent unwanted nois

34、e from interfering with system performance. Volume Control Adjust the volume to a comfortable level using the front-panel Volume Control or remote Volume Up/Down Buttons . When listening in one of the Stereo modes with the surround circuits off, the Balance Control may be used to adjust the relative

35、 sound output between the front left and right speakers. For all other modes, it is important that the Balance Control remain in the “12 oclock” position in order to ensure a proper sound field presentation. To temporarily silence all speaker outputs, press the Mute ButtonK.This will interrupt the o

36、utput to all speakers and the headphone jack, but it will not affect any recording or dubbing that may be in progress.When the system is muted, the word MUTE will flash in the Lower Display Line . Press the Mute ButtonK again to return to normal operation. You may adjust the bass and treble tone con

37、trols at any point during a listening session by simply turn- ing the Bass Control or Treble Control until the desired setting is achieved.You may also totally remove the tone controls from the circuit so that the output is “flat” by pressing the Tone Mode Button 5 and then pressing the /Button ) so

38、 that TONE OFF appears in the on-screen display and the Lower Display Line . For private listening, plug the 1/4 stereo phone plug from a pair of stereo headphones into the front-panel Headphone Jack 4.When the headphone plug is connected, all speakers will be silenced and DOLBY H:BP will scroll onc

39、e across the Lower Display Line , indicating that the headphone output is in the Bypass mode, and 33 34 35 36 37 38 39 40 41 48 49 46 47 44 45 42 43 38 39 40 41 31 32 30 28 29 2526 27 28 29 30 24 23 22 21 2031 37 36 35 34 33 3231 37 36 35 34 33 32 48 49 50 5147 46 45 44 43 42 33 34 35 36 37 38 39 40

40、 41 48 49 46 47 44 45 42 43 38 39 40 41 31 32 30 28 29 2526 27 28 29 30 24 23 22 21 2031 37 36 35 34 33 3231 37 36 35 34 33 32 48 49 50 5147 46 45 44 43 42 ? 33 34 35 36 37 38 39 40 41 48 49 46 47 44 45 42 43 38 39 40 41 31 32 30 28 29 2526 27 28 29 30 24 23 22 21 2031 37 36 35 34 33 3231 37 36 35 3

41、4 33 32 48 49 50 5147 46 45 44 43 42 33 34 35 36 37 38 39 40 41 48 49 46 47 44 45 42 43 38 39 40 41 31 32 30 28 29 2526 27 28 29 30 24 23 22 21 2031 37 36 35 34 33 3231 37 36 35 34 33 32 48 49 50 5147 46 45 44 43 42 33 34 35 36 37 38 39 40 41 48 49 46 47 44 45 42 43 38 39 40 41 31 32 30 28 29 2526 2

42、7 28 29 30 24 23 22 21 2031 37 36 35 34 33 3231 37 36 35 34 33 32 48 49 50 5147 46 45 44 43 42 33 34 35 36 37 38 39 40 41 48 49 46 47 44 45 42 43 38 39 40 41 31 32 30 28 29 2526 27 28 29 30 24 23 22 21 2031 37 36 35 34 33 3231 37 36 35 34 33 32 48 49 50 5147 46 45 44 43 42 90? min 80? min 70? min 60

43、? min 50? min 40? min 30? min 20? min 10? min OFF OPERATION 27 AVR335 AVR335 harman/kardon www.freeservicemanuals.infoIts Free www.freeservicemanuals.info RadioFans.CN 收音机爱 好者资料库 OPERATION 28 OPERATION to confirm that no processing is being used.When the headphone plug is removed, the audio feed to

44、the speakers will be restored. When the headphones are in use, you may take advantage of the Dolby Headphone modes to bring added spaciousness to headphone listening. Press the Dolby Mode Select Button w or the Surround Mode Group Selector 7 to cycle through the three Dolby Headphone modes and selec

45、t the one that you prefer. Surround Mode Selection One of the most important features of the AVR 335 is its ability to reproduce a full multichannel surround sound field from digital sources, analog matrix surround-encoded programs and standard stereo programs. Selection of a surround mode is based

46、on personal taste, as well as the type of program source material being used. For example, motion pictures or TV programs bearing the logo of one of the major surround-encoding processes, such as Dolby Surround or DTS Stereo, may be played in either the Dolby Digital, Dolby Pro Logic II Cinema, DTS

47、Neo:6 Cinema or Logic 7 Cinema surround modes, depending on the source material. NOTE: Once a program has been encoded with matrix surround information, it retains the surround information as long as the program is broadcast in stereo.Thus, movies with surround sound may be decoded via any of the an

48、alog surround modes such as Dolby Pro Logic II Movie, Logic 7 Cinema or DTS Neo:6 Cinema, when they are broadcast via conventional TV stations, cable, pay-TV and satellite transmission. In addition, a growing number of made-for-television programs, sports broad- casts, radio dramas and music CDs are

49、 also recorded in surround sound. Even when a program is not listed as carrying intentional surround information, you may find that the Dolby Pro Logic II, Logic 7 Enhanced or DTS Neo:6,VMAx and the Hall or Theater modes often deliver enveloping sur- round presentations through the use of the natural infor- mation present in all ste