HarmanKardon-AVR210-avr-sm维修电路原理图.pdf

《HarmanKardon-AVR210-avr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《HarmanKardon-AVR210-avr-sm维修电路原理图.pdf（135页珍藏版）》请在收音机爱好者资料库上搜索。

1、 harman/kardon AVR210 AVR210 A/V DOLBY DIGITAL RECEIVER SERVICE MANUAL CONTENTS ESD WARNING.2 LEAKAGE TESTING.3 BASIC SPECIFICATIONS.4 FRONT PANEL CONTROLS.5 REAR PANEL CONNECTIONS.9 REMOTE CONTROL FUNCTIONS.11 TROUBLESHOOTING GUIDE.14 PROCESSOR RESET.14 IDLE CURRENT/TUNER ALIGNMENT15 BULLETIN # H/K

2、2001-01.16 BULLETIN # H/K2001-03.18 BULLETIN # H/K2003-07.19 TECH TIP# HKTT2002-01.21 TECH TIP# HKTT2003-01.23 TECH TIP# HKTT2004-03.24 UNIT EXPLODED VIEW.28 EXPLODED VIEW PARTS LIST.29 BLOCK DIAGRAMS.30 PCB DRAWINGS.32 ELECTRICAL PARTS LIST.44 SEMICONDUCTOR PINOUTS.65 SCHEMATICS.115 WIRING DIAGRAM.

3、132 PACKAGE135 harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev2 6/2005 RadioFans.CN 收音机爱 好者资料库 Eachprecautioninthismanualshouldbefollowedduringservicing. Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a component

4、identified with , use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably insulated from t

5、he supply circuit before retuming the product to the customer. Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field eff

6、ect transistors and semiconductor chip components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge

7、on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices

8、, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge build-up or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static solder removal device. Some solder removal devices not clas

9、sified as anti-static can generate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are

10、ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.) 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective materia

11、l to the chassis or circuit assembly into which the device will be installed. Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing t

12、ogether or your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices. CAUTION : 2 AVR210 AVR210 harman/kardon RadioFans.CN 收音机爱 好者资料库 1. Inspect all lead dress to make certain that leads are not pinched or that hardware i

13、s not lodged between the chassis and other metal partsintheunit. 2. Be sure that any protective devices such as nonmetallic control knobs, insulating fish- papers,cabinetbacks,adjustmentand compartment covers or shields, isolation resistor-capacitynetworks,mechanical insulators, etc. Which were remo

14、ved for the servicingareproperlyre-installed. Before returning the unit to the user, perform the following safety checks : 3. Be sure that no shock hazard exists ; check for leakage currentusingSimpsonModel229LeakageTester,standard equipment item No. 21641, RCA Model WT540A or use alternate method a

15、sfollows : Plug the power cord directly Into a 120 volt AC receptacle (do not use an Isolation Transformer for this test). Using two clip leads, connect a 1500ohms,10wattResistorparalleledbya0.15uFcapacitor,inserieswithallexposedmetalcabinetpartsandaknownearthground,such as a water pipe or conduit.

16、Use a VTVM or VOM with 1000 ohms per volt, or higher sensitivity to measure the AC voltage drop across the resistor. (See diagram) Move the resistor connection to each exposed metal part having a return path to the chassis (antenna, metal, cabinet,screwheads,knobsandcontrolshafts,escutcheon,etc.)and

17、measuretheACvoltagedropacrosstheresistor.(Thistestshouldbe performedwiththe0.35voltRMSormoreisexcessiveandindicatesapotentialshockhazardwhichmustbecorrectedbeforereturningthe unittotheowner. 3 AVR210 AVR210 harman/kardon RadioFans.CN 收音机爱 好者资料库 4 SPECIFICATIONS Technical Specifications Audio Section

18、 Stereo Mode Continuous Average Power (FTC) 50 Watts per channel, 20Hz20kHz, 0.07% THD, both channels driven into 8 ohms Five-Channel Surround Modes Power Per Individual Channel Front L press it again to turn the unit off. Note that the Power Indicator surrounding the switch 3 will turn green when t

19、he unit is on. 3 Power Indicator: This LED will be illumi- nated in amber when the unit is in the Standby mode to signal that the unit is ready to be turned on.When the unit is in operation, the indicator will turn green. 4 Headphone Jack:This jack may be used to listen to the AVR 210s output throug

20、h a pair of headphones. Be certain that the headphones have a standard 1/4 stereo phone plug. Note that the main room speakers will automatically be turned off when the headphone jack is in use. 5 Selector Buttons:When you are establish- ing the AVR 210s configuration settings,use these buttons to s

21、elect from the choices available, as shown in the Main Information Display . 6 Tone Mode: Pressing this button enables or disables the Bass and Treble tone controls. When the button is pressed so that the words TONE IN appear in the Main Information Display , the settings of the Bass the tuner will

22、automatically scan for the next station with an acceptable signal and then stop. 9 Tuner Band Selector: Pressing this button will automatically switch the AVR 210 to the Tuner mode. Pressing it again will switch between the AM and FM frequency bands. (See page 28 for more information on the tuner.)

23、) Preset Stations Selector: Press this button to scroll up or down through the list or stations that have been entered into the preset memory. (See page 28 for more information on tuner programming.) ! Input Source Selector: Press this button to change the input by scrolling up or down through the l

24、ist of input sources. FM Mode Selector: Press this button to select Auto or Manual tuning.When the button is pressed so that the AUTO indicator W lights, the tuner will search for the next station with an acceptable signal when the Tuning Selector 8u is pressed.When the button is pressed so that the

25、 AUTO indicator W is not lit, each press of the Tuning Selector 8u will increase the frequency. (See page 28 for more information on using the tuner.) # Digital Optical 3 Input: Connect the opti- cal digital output of an audio or video product to this jack.When the Input is not in use, be certain to

26、 keep the plastic cap installed to avoid dust contamination that might degrade future performance. $ Digital Coax 3 Jack: This jack is used for connection to the output of portable audio devices, video game consoles or other products that have a coax digital jack. % Video 4 Video Input Jacks: These

27、jacks may be used for temporary connection to the composite or S-Video output of video games, camcorders or other portable video products. Video 4 Audio Input Jacks: These audio/video jacks may be used for temporary connection to video games or portable audio/video products such as camcorders and po

28、rtable audio players. VMAx N appears when the Near Field VMAx mode is selected. (See page 25 for a description of the VMAx modes.) J 5-Channel Stereo Indicator: This indica- tor lights when the 5-Channel Stereo mode has been selected. K Logic 7 Mode Indicators: These indica- tors light when the Logi

29、c 7 mode is in use. LOGIC 7C appears for the Cinema version of Logic 7; LOGIC 7M appears for the Music version of Logic 7. (See page 25 for a description of the Logic 7 modes.) L Hall Mode Indicator: This indicator lights when the Hall mode have been selected. M OSD Indicator: When the OSD system is

30、 in use, this indicator lights to remind you that the other indicators in this display do not function when the On Screen Display is being used. N Theater Mode Indicator:This indicator lights to show that the Theater mode is in use. O Night Mode Indicator: This indicator lights when the AVR 210 is i

31、n the Night mode, which preserves the dynamic range of digital program material at low volume levels. P Speaker/Channel Input Indicators: These indicators are multipurpose, indicating either the speaker type selected for each channel or the incoming data-signal configuration.The left, center, right,

32、 right surround and left surround speaker indicators are composed of three boxes, while the subwoofer is a single box.The center box lights when a “Small” speaker is selected, and the two outer boxes light when “Large” speakers are selected.When none of the boxes are lit for the center, surround or

33、subwoofer channels, no speaker has been selected for one of those positions. (See page 19 for more infor- mation on configuring speakers.) The letters inside each of the center boxes display active input channels. For standard analog inputs, only the L and R will light, indicating a stereo input. Wh

34、en a digital source is playing, the indicators will light to display the channels being received at the digital input.When the letters flash, the digital input has been interrupted. (See page 27 for more information on the Channel Indicators.) Q Preset Number/Sleep Timer: When the tuner is in use, t

35、hese numbers indicate the spe- cific preset memory location in use. (See page 28 for more information on preset stations.) When the Sleep function is in use, these num- bers show how many minutes remain before the unit goes into the Standby mode. R Preset Indicator: This indicator lights when the tu

36、ner is in use to show that the Preset Number/Sleep Timer Q is showing the stations preset memory number. (See page 28 for more information on tuner presets.) S Sleep Indicator: This indicator lights when the Sleep function is in use.The numbers in the Preset Number/Sleep Timer Indicators will show t

37、he minutes remaining before the AVR 210 goes into the Standby mode. (See page 24 for more information on the Sleep function.) AVR210 AVR210 harman/kardon RadioFans.CN 收音机爱 好者资料库 8 FRONT PANEL INFORMATION DISPLAY Front Panel Information Display TMemory Indicator: This indicator flashes when entering

38、presets and other information into the tuners memory. U Stereo Indicator:This indicator lights when an FM station is being tuned in stereo. VTuned Indicator:This indicator lights when a station is being received with sufficient signal strength to provide acceptable listening quality. W Auto Indicato

39、r: This indicator lights when the tuners Auto mode is in use. X Main Information Display: This display shows messages relating to the status, input source, surround mode, tuner, volume level or other aspects of the AVR 210s operation. Y Mute Indicator: This indicator lights to remind you that the AV

40、R 210s output has been silenced by pressing the Mute button . Press the Mute button again to return to the pre- viously selected output level. 38 AVR210 AVR210 harman/kardon RadioFans.CN 收音机爱 好者资料库 9 REAR PANEL CONNECTIONS Rear Panel Connections AC INPUT 120V/60HZ A R CUS LISTED E191351 40KK AUDIO E

41、QUIPMENT TAPE FRONT SPKRS (8) RIGHTLEFT CENTER SPKR (8) PRE OUT6 CH. DIRECT INPUT ANTENNA DIGITAL IN DIGITAL OUT VID 3VID 3 REMOTE VID 2VID 2 OPT OPT COAX COAX VID 1VID 1 DVDDVD CD MON. OUT IN OUT AM GND FM 75 IN OUT 1 2 1 2 IN OUT IN OUT IN OUT L R CENTER SL FL SUBWOOFER SR FR L R VIDEO S-VIDEO + +

42、 SURR. SPKRS (8) SERIAL NO. MODEL NO. AVR 210 NORTHRIDGE CALIFORNIA, USA MADE IN CHINA AC OUTLETS 120V/60Hz UNSWITCHED / 100W MAX SWITCHED / 100W MAX RIGHTLEFT ? fi ? fl ? ? ? ? a b c d e ? ? ? f g j ? ? ? ? FL FR SL SR CENTER SUBWOOFER 31 IN OUT hk ? ? ? ? ? ? ? i ? Tape Inputs Tape Outputs Video 1

43、 Audio Inputs AM Antenna Video 1 Audio Outputs DVD Audio Inputs FM Antenna CD Inputs 6-Channel Direct Inputs Digital Audio Outputs Preamp Outputs Subwoofer Output Video Monitor Outputs Front Speaker Outputs fi Surround Speaker Outputs fl Switched AC Accessory Outlet Unswitched AC Accessory Outlet AC

44、 Power Cord Remote IR Output a Remote IR Input b DVD Video Inputs c Video 1 Video Outputs d Video 3 Video Inputs e Video 2 Video Inputs f Video 2 Video Outputs g Video 1 Video Inputs h Optical Digital Inputs i Coaxial Digital Inputs jVideo 2 Audio Outputs kVideo 3 Audio Inputs VIdeo 2 Audio Inputs 3

45、7 AVR210 AVR210 harman/kardon RadioFans.CN 收音机爱 好者资料库 10 REAR PANEL CONNECTIONS Rear Panel Connections Tape Inputs: Connect these jacks to the PLAY/OUT jacks of an audio recorder. Tape Outputs: Connect these jacks to the RECORD/INPUT jacks of an audio recorder. Video 1 Audio Inputs: Connect these ja

46、cks to the PLAY/OUT audio jacks on a VCR or other video source. AMAntenna: Connect theAM loop antenna supplied with the receiver to these terminals.If an externalAM antenna is used,make connections to the AM and GND terminals in accordance with the instructions supplied with the antenna. Video 1 Aud

47、io Outputs: Connect these jacks to the RECORD/INPUT audio jacks on a VCR. DVD Audio Inputs: Connect these jacks to the analog audio jacks on a DVD or other video source. FM Antenna: Connect the supplied indoor or an optional external FM antenna to this terminal. CD Inputs: Connect these jacks to the

48、 out- put of a compact disc player or CD changer. 6-Channel Direct Inputs: If an external digital audio decoder is used, connect the out- puts of that decoder to these jacks. Digital Audio Outputs: Connect these jacks to the matching digital input connector on a digital recorder such as a CD-R or MiniDisc recorder. Preamp Outputs: These jacks may be connected to an external power amplifier. Subwoofer Output: Connect this jack to the line-level input of a powered subwoofer. If an external s