HarmanKardon-AVR140-avr-sm维修电路原理图.pdf

《HarmanKardon-AVR140-avr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《HarmanKardon-AVR140-avr-sm维修电路原理图.pdf（159页珍藏版）》请在收音机爱好者资料库上搜索。

1、 harman/kardon AVR140 AVR140 6 X 40W 6.1 CHANNEL A/V RECEIVER PRELIMINARY SERVICE MANUAL CONTENTS ESD WARNING.2 LEAKAGE TESTING.3 BASIC SPECIFICATIONS.4 PACKAGING.5 FRONT PANEL CONTROLS.6 REAR PANEL CONNECTIONS.8 REMOTE CONTROL FUNCTIONS.10 CONNECTIONS.13 OPERATION.15 TROUBLESHOOTING GUIDE.21 PROCES

2、SOR RESET.21 DISASSEMBLY.22 UNIT EXPLODED VIEW.23 EXPLODED VIEW PARTS LIST24 AMP BIAS ADJUSTMENT.25 TECH TIP HK2003-01.26 BLOCK DIAGRAM.27 PCB DRAWINGS28 ELECTRICAL PARTS LIST.34 SEMICONDUCTOR PINOUTS.68 SCHEMATICS152 WIRING DIAGRAM.159 harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 1

3、1797 www.freeservicemanuals.infoIts Free www.freeservicemanuals.info RadioFans.CN 收音机爱 好者资料库 Eachprecautioninthismanualshouldbefollowedduringservicing. Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a component identified with , use only

4、 the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably insulated from the supply circuit before r

5、etuming the product to the customer. Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and semico

6、nductor chip components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a

7、 known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a

8、conductive surface such as aluminum foil, to prevent electrostatic charge build-up or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can

9、generate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most

10、 replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.) 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circui

11、t assembly into which the device will be installed. Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together or your clothes fa

12、bric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices. CAUTION : AVR140 AVR140 harman/kardon www.freeservicemanuals.infoIts Free www.freeservicemanuals.info RadioFans.CN 收音机爱 好者资料库 2 SAFETY PRECAUTIONS The following check should be

13、performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Measure leakage current to a known earth ground (water pipe, conduit, etc.) by connecting a leakage current tester between the earth ground and all exposed metal parts of the appliance (input/output

14、terminals, screwheads, metal overlays, control shaft, etc.). Plug the AC line cord of the appliance directly into a 120V AC 60Hz outlet and turn the AC power switch on. Any current measured must not exceed o.5mA. ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL SHO

15、CK HAZARD AND MUST BE CORRECTED BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER. Device under test Test all exposed metal surfaces Also test with plug reversed (Using AC adapter plug as required) AC Leakage Test Leakage current tester Reading should not be above 0.5mA Earth ground AVR140 AVR140 harma

16、n/kardon www.freeservicemanuals.infoIts Free www.freeservicemanuals.info RadioFans.CN 收音机爱 好者资料库 Audio Section Stereo Mode Continuous Average Power (FTC) 50 Watts per channel, 20Hz20kHz, 0.07% THD, both channels driven into 8 ohms Six-Channel Surround Modes Power per Individual Channel Front L press

17、 it again to turn the unit off.The Power Indicator 3 turns blue when the unit is on. 4 Headphone Jack: This jack may be used to listen to the AVR 140s output through a pair of headphones. The speakers will automatically be turned off when the headphone jack is in use. 5 Tone Mode: This button contro

18、ls the tone mode settings, enabling adjustment of the bass and treble boost/cut.You may also use it to take the tone con- trols out of the signal path completely for “flat” response.The first press of the button displays a TONE IN message in the Lower Display Line and in the on-screen display.To tak

19、e the controls out of the signal path, press either of the / Buttons ) until the display reads TONE OUT. To change the bass or treble settings, make sure that TONE IN appears in the Lower Display Line or press either of the / Buttons ) until it does. Press the Tone Mode Button 5 until the desired op

20、tion of TREBLE MODE or BASS MODE appears in the Lower Display Line and in the on-screen display and then press either of the / Buttons ) to enter the desired boost or cut setting. Both treble and bass contours may be boosted or cut by up to + or 10dB in increments of 2dB. See pages 17 and 25 for mor

21、e information on the tone controls. NOTE: The AVR 140 is not equipped with a traditional Balance control.When listening to two-channel materi- als, if you wish to adjust the stereo image, you may use the Channel Adjust Selector to increase or decrease the level of the left front channel by up to + o

22、r 10dB, and then to decrease or increase the right front channel by the corresponding amount. However, when listening to surround materials and most two- channel materials, it is recommended that you leave these settings at the results obtained during the config- uration process described on pages 1

23、5 through 24. 6 Speaker Selector: Press this button to begin the process of configuring the unit to match the type of speakers used in your listening room. (See pages 2022 for more information on speaker setup and configuration.) 1 Main Power Switch 2 Power Indicator 3 Standby/On Switch 4 Headphone

24、Jack 5 Tone Mode 6 Speaker Selector 7 Surround Mode Group Selector 8 Surround Mode Selector 9 Tuning Selector )/Buttons ! Tuner Band Selector Set Button # Digital Input Selector $ Preset Station Selector % Delay Adjust Selector Input Source Selector continue to hold the button until the Sleep indica

25、tor numbers disappear and the words SLEEP OFF appear in the Lower Display Line Q. When you will be away from home for an extended period of time it is always a good idea to completely turn the unit off with the front-panel Main Power Switch 1. NOTE: All preset memories are lost if the unit is left t

26、urned off by using the Main Power Switch 1 for more than four weeks. Source Selection To select a source, press any of the Input Selector Buttons eg? on the remote. The input source may also be changed by pressing the front-panel Input Source Selector Button . Each press of the button will move the

27、input selection through the list of available inputs. As the input is changed, the AVR 140 will auto- matically switch to the digital input (if selected), component video input, surround mode, output levels and night mode status as well as any speaker configuration settings established by using the

28、INDEPENDENT Bass Management setting, that were entered during the configuration process for that source. When the input source is changed, the new input name and the digital (or analog) audio input will appear in the Upper Display Line P, and the current surround mode will appear in the Lower Displa

29、y Line .The same messages will also appear momentarily in the on-screen display in the lower third of the screen (semi-OSD). When an audio source is selected, the last video input used remains routed to the Video 1 Video and S- Video Outputsekand Component Video and S-Video Monitor Outputs h.This pe

30、rmits you to simultaneously view and listen to different sources. The front-panel Video 3 Inputs , Optical 3 Digital Input * or the Coaxial 3 Digital Input ( may be used to connect a device such as a video game or camcorder to your home entertainment system on a temporary basis. When Digital Media P

31、layer (DMP) source is selected, if a compatible Apple iPod device is inserted in an optional Harman Kardon that is connected to DMP Connector b on the rear panel, function messages will appear on any video display connected to the AVRs Video Monitor Outputs h, and the remote control may be used to n

32、avigate the iPod and access many of its functions.The function messages will also appear in the front-panel display, and the iPods bat- tery may be charged. See the owners guides for and your iPod for more information. 6-Channel/8-Channel Direct Input There are two input choices available for use wi

33、th sources such as a DVD-Audio or SACD player that are connected to the 6/8-Channel Direct Inputs g. Select the appropriate input according to the way your system and source equipment are configured: I6 CH DIRECT should be used when the SBR and SBL inputs are NOT in use. It is assumed that the input

34、 source device has its own internal bass management system.This input passes the input from the source directly through to the volume control without any analog to digital conversion and it mutes the unused input jacks to prevent unwanted noise from interfering with sys- tem performance. I8 CH DIREC

35、T should be used when an input is connected to all eight 8-Channel Direct Inputs g. It is assumed that the input source device has its own internal bass management system.This input passes the input from the source directly through to the volume control without any analog-to-digital conversion and i

36、t mutes the unused input jacks to prevent unwanted noise from interfering with system performance. Volume Control Adjust the volume to a comfortable level using the front-panel Volume Control or remote Volume Up/Down Buttons ?. To temporarily silence all speaker outputs, press the Mute Button ?.This

37、 will interrupt the output to all speakers and the headphone jack, but it will not affect any recording or dubbing that may be in progress.When the system is muted, the word MUTE will flash in the Upper Display Line P. Press the Mute Button ? again to return to normal operation. You may adjust the b

38、ass and treble tone controls at any point during a listening session by pressing the Tone Mode Button 5 until TONE IN appears in the Lower Display Line . Press the Tone Mode Button 5 again until either TREBLE MODE or BASS MODE The BridgeTM The BridgeTM The BridgeTM The BridgeTM ? OPERATION OPERATION

39、 25 AVR 140 OM 7/15/05 5:35 PM Page 25 AVR140 AVR140 harman/kardon www.freeservicemanuals.infoIts Free www.freeservicemanuals.info RadioFans.CN 收音机爱 好者资料库 26 OPERATION OPERATION appears in the Lower Display Line 5, and then use the Buttons o to boost or cut the low or high frequencies by up to 10dB,

40、 in 2dB steps, until the desired setting is achieved.You may also totally remove the tone controls from the circuit so that the output is “flat” at any time by pressing the Tone Mode Button 5 and then pressing the / Button ) so that TONE OUT appears in the on-screen display and the Lower Display Lin

41、e . For private listening, plug the 1/4 stereo phone plug from a pair of stereo headphones into the front-panel Headphone Jack 4.When the headphones plug is connected, the phrase HEADPHONES IN will scroll once across the Lower Display Line Q and all speakers will be silenced.When the headphone plug

42、is removed, the audio feed to the speakers will be restored. Surround Mode Selection One of the important features of the AVR 140 is its ability to reproduce a full multichannel surround sound field from digital sources, analog matrix surround- encoded programs and standard stereo programs. Selectio

43、n of a surround mode is based on personal taste, as well as the type of program source material being used. For example, motion pictures or TV pro- grams bearing the logo of one of the major surround- encoding processes, such as Dolby Surround or DTS Stereo, may be played in either the Dolby Digital

44、, Dolby Pro Logic II or IIx Movie, DTS Neo:6 Cinema, or Logic 7 5.1 or 7.1 Cinema surround modes. NOTE: Once a program has been encoded with matrix surround information, it retains the surround information as long as the program is broadcast in stereo.Thus, movies with surround sound may be decoded

45、via any of the analog surround modes such as Dolby Pro Logic IIx Cinema, Logic 7 Cinema or DTS Neo:6 Cinema, when they are broadcast via conventional TV stations, cable, pay-TV and satellite transmission. In addition, a growing number of made-for-television programs, sports broad- casts, radio drama

46、s and music CDs are also recorded in surround sound. Even when a program is not listed as carrying inten- tional surround information, you may find that the Dolby Pro Logic IIx, Logic 7 Enhanced or DTS Neo:6,VMAx and the Hall or Theater modes often deliver enveloping surround presentations through t

47、he use of the natural information present in all stereo recordings. Surround modes may be changed at any time by using either the front panel or remote control.Any changes made to the surround mode for that source will be retained in the AVRs menu, even after another source is selected, or if the AV

48、R is placed in Standby mode.To select a new surround mode from the front panel, first press the Surround Mode Group Selector Button 7 until the desired major surround mode group, such as Dolby, DTS or Logic 7, is select- ed. Next, press the Surround Mode Selector Button 8 to choose the specific indi

49、vidual surround mode. To select a surround mode using the remote, press the button for the major surround mode group that includes the mode you wish to choose from: Dolby w, DTS Surround x, DTS Neo:6 ?, Logic 7 y, Stereo ? or DSP Surround k. The first press of the button will show the current mode from that group.To cycle through the available modes in that group, press the button again until the desired mode appears