Hafler-9130-pwr-sm维修电路原理图.pdf

《Hafler-9130-pwr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Hafler-9130-pwr-sm维修电路原理图.pdf（20页珍藏版）》请在收音机爱好者资料库上搜索。

1、H O M E A U D I O C O M P O N E N T S 0 W N E R S M A N U A L Series 09130 P 0 W E RA M P L I F I E R RadioFans.CN 收音机爱 好者资料库 Series 9130 Power Amplifier NOTICE-IMPORTANT SAFETY INFORMATION Ap!J!A WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. 1. 2 . 3 .

2、4 . 5 . 6 .VENTILATION 7 . 8 .POWER SOURCES 9 . 10. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the products enclosure, that may be of sufficient magnitude to constitute a risk of ele

3、ctric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and mainte- nance (servicing) instructions in the literature accompanying the appliance. READ INSTRUCTIONS All the safety and operating instructions of yo

4、ur Hafler equipment should be read before power is applied to the equipment. RETAIN OWNERS MANUAL These safety and operating instructions should be retained for future reference. HEED WARNINGS All warnings on the equipment and in the operating instructions are important and should be followed. FOLLO

5、W INSTRUCTIONS All operating and use instructions are important and should be followed. HEAT The equipment should be kept away from areas of high temperature, such as heater vents, radiators, stoves/ovens, fireplaces, etc. The equipment should be used in an area suitable for proper ventilation. Care

6、 should be taken not to impede airflow in and around the cabinet. Do not mount on a carpeted shelf or in a sealed enclosure. Allow for proper clearance above the equipment. WATER AND MOISTURE The equipment should not be used in or around water, such as a bathtub, sink, or swimming area. Also, the eq

7、uipment should not be used in areas prone to flooding, such as a basement. The equipment should be connected only to a power source of the same voltage and frequency as that listed on the rear panel above the power cord entry point. POWER CORD PROTECTION Power cords should be arranged so that they d

8、o not interfere with the movement of objects in the room: people, fan blades, utility carts, etc. Also, care should be taken that the cord is not pinched or cut, and placed so that it is not in danger of being pinched or cut, as in under a rug, around a tight corner, etc. POWER CORD GROUNDING The po

9、wer supply cord is of a three wire grounded type, designed to reduce the risk of electric shock sustained from a live cabinet. It is assumed to be of suitable length for most uses of the equipment. The use of extension cords and power strips is discouraged unless they are of suitable rating to deliv

10、er the required total current for safe operation of all connected equipment. Furthermore, extension cords or power strips must provide the same three wire grounded connection.It is important that the blades of the equipments plug be able to fully insert into the mating receptacle. Never remove the r

11、ound grounding pin on the plug in an attempt to mate to a two wire ungrounded receptacle: use a grounding adaptor with the grounding tab or wire suitably connected to earth ground. -l- RadioFans.CN 收音机爱 好者资料库 11.NON-USE PERIODS During periods of extended non-use, the power cord should be unplugged f

12、rom the power source. 12.CLEANING The equipment should be cleaned only as detailed in the operating instructions. 13.OBJECT AND LIQUID ENTRY Care should be taken so that objects and/or liquids, such as cleaning fluids or beverages, are not spilled into the enclosure of the equipment. 14.DAMAGE REQUI

13、RING SERVICE Hafler equipment should be serviced by qualified service personnel when: A.The power supply cord or plug has been damaged, or B .Objects have fallen, or liquid has been spilled into the equipment, or C.The equipment has been exposed to rain, or D.The equipment does not appear to operate

14、 normally or exhibits a marked change in performance, or E .The equipment has been dropped, or the enclosure has been damaged. 15.SERVICING The user should not attempt to service the equipment beyond that which is described in the operating instructions. All other service should be referred to quali

15、fied service personnel. 16.CARTS AND STANDS The equipment should be used with carts or stands only of sufficient strength and stability for the use intended. An equipment and cart combination should be moved with care. Quick stops and starts, excessive force, and uneven surfaces may cause the equipm

16、ent and cart combination to topple. -2- RadioFans.CN 收音机爱 好者资料库 TABLE OF CONTENTS PERFORMANCE SPECIFICATIONS . 4 General Information . 4 INSTALLATION Rackmounting . 5 Ventilation/Placement . 5 Line Voltage.5 OPERATION/CONNECTIONS Power Cord Connection/Power Switch . 5 Inputs .5 Front Panel View Diag

17、ram . 6 Rear Panel View Diagram . 7 Outputs.8 GainControls.8 Mono/Stereo Switching . 8 Soft Turn-On System . 8 Thermal Protection System . 8 CIRCUIT HIGHLIGHTS . 9 ADDITIONAL INFORMATION Loudspeaker Load Impedance Considerations . 9 Changing Line Voltage Rating.10 AdjustingBias .10 General Troublesh

18、ooting Hints . 11 Ground Loops . 11 Cleaning/Maintenance . 12 Functional Block Diagram . 13 Parts List .14 Component Layout Diagram . 15 Circuit Schematic Diagram.17 SERVICE POLICY AND LIMITED WARRANTY.19 -3- RadioFans.CN 收音机爱 好者资料库 PERFORMANCE SPECIFICATIONS GENERAL INFORMATION All specifications a

19、re for 20 Hz - 20 kHz, at full power into 8 ohms, unless specified otherwise. Power Rating: Rated THD: Full Power Bandwidth: Signal to Noise Ratio: Input Impedance: Input Sensitivity: Damping Factor: Controls: Inputs: outputs: Power Consumption: Size: Weight: 65 watts per channel (8 ohms) less than

20、0.008% 4 Hz to 40 kHz greater than 100 dB, unweighted 22,000 ohms 1.1 volts RMS 100 to 1 kHz, 50 to 10 kHz Power Switch, Left/Right Gain Controls, Mono/Stereo Switch Right and Left/Mono RCA jacks Right, Left, and Mono 5-way Binding Posts 40 watts quiescent, 600 watts maximum 17”(W) x 9”(D) x 3.5”(H)

21、 excluding feet, faceplate 17” or 19”(W) 43.2cm(W) x 22.8cm(D) x 8.9cm(H) excluding feet, faceplate 43.2cm or 48.3cm(W) 20 Ibs., 9 kg, net. -4- RadioFans.CN 收音机爱 好者资料库 INSTALLATION RACKMOUNTING VENTILATION/ PLACEMENT LINE VOLTAGE The 9130 Amplifier is supplied in either a 17” Black Version, or a 19”

22、 Silver Version. The 19” model has rackmounting holes provided for installation in equipment racks. The holes are on standard EIA spacings.Due to conflict with adjacent equipment, it may be advisable to remove the four rubber feet from the bottom of the unit. The feet may be removed from the outside

23、, with no dis-assembly of the chassis necessary. The 9130 Amplifier can produce considerable heat during normal operation. The amplifier should be placed on a hard, smooth surface to allow air to circulate beneath the unit. Additionally, allow at least one inch of free space on either side, and seve

24、ral inches above and behind the amplifier to allow air circulation around the heatsinks. This is particularly important when the unit is installed in a closed cabinet. In applications where the amplifier is driving low impedance and/or low efficiency loudspeakers at high levels, thermal shutdown may

25、 occur if inadequate ventilation is provided. If this occurs, it may be necessary to move the amplifier to a location with better free air circulation. The amplifier should be located at least several inches away from sensitive components, (such as preamplifiers, tuners, CD players, turntables, etc.

26、) due to the possibility of audible hum or buzz from magnetic radiation. The 9130 Amplifier is configurable for either 100, 120, or 230 volt operation. This is accomplished by moving the Voltage Selector on the printed circuit board. The procedure is detailed in the section “CHANGING LINE VOLTAGE RA

27、TING”. Make sure that the unit is configured for your local AC line voltage before attempted use. The configuration is labelled directly above the power cord connector. (Units wired for 230VAC may be used over a range of 220 to 240VAC.) OPERATION/CONNECTIONS POWER CORD CONNECTION/ POWER SWITCH INPUT

28、S Units wired for 100 and 230 VAC are supplied without power cords. Local agents will supply cords with male connectors appropriate to the local standard. Units wired for 120 VAC are supplied with a detachable AC power cord. The female connector plugs into the receptacle provided on the rear panel.

29、This power cord is a standard IEC Type 320, 3-wire, 16 gauge assembly. Should replacement ever be necessary, be sure to replace it with an identical cord. Never remove the grounding pin from the male end of the cord. In applications where a grounded outlet is not available, a ground adaptor should b

30、e employed, with the ground tab or wire of the adaptor connected to a suitable earth ground. The AC power cord of the amplifier must be connected to a receptacle capable of delivering a minimum of 600 watts. The convenience outlets of some preamplifiers are not rated for this power level. Before con

31、necting the amplifier, be sure to check the rating of such outlets, and take into account the power consumption of any other connected components to determine the total maximum power consumption. If the amplifier is connected to a component with a switched convenience outlet, then the amplifiers Pow

32、er Switch may be left ON at all times, and the power controlled by the switched outlet. If the amplifier is connected to an unswitched outlet, then the amplifiers power should be controlled by the front panel Power Switch. All input connections to the amplifier must be performed with the amplifier o

33、ff! The left and right audio inputs to the amplifier are via standard RCA jacks. Connect these jacks to the output of the preamplifier or other signal source. When operating the amplifier in the Mono Mode, only the left channel input should be used. -5- RadioFans.CN 收音机爱 好者资料库 LEFT/MONO GAIN POWER S

34、WITCH UP - ON DOWN- O F F I (3, I RACKMOUNT HOLESRIGHT (19” VERSION ONLY)GAIN 9130 AMPLIFIER FRONT PANEL VIEW RadioFans.CN 收音机爱 好者资料库 -7- RadioFans.CN 收音机爱 好者资料库 OUTPUTSAll output connections to the amplifier must be performed with the amplifier off! GAIN CONTROLS MONO/ STEREO SWITCHING SOFT TURN- O

35、N/OFF SYSTEM THERMAL PROTECTION SYSTEM The left and right audio outputs from the amplifier are via standard 5-way type, 3/4” spacing, binding posts. Connect these binding posts to the loudspeakers. The amplifiers binding posts will accept single or dual banana plugs, spade lugs, pin plugs, or bare w

36、ires. If using bare wires, it is recommended that the ends of the wire be tinned with solder so that no stray strands can cause a short circuit to the chassis or adjacent terminals. To ensure proper speaker phasing and frequency response, be sure to connect each respective amplifier RED (+) terminal

37、 to the speaker RED (+) terminal, and the amplifier BLACK (-) terminal to the speaker BLACK (-) terminal. The polarity symbols (+/-) for Stereo Mode are labelled directly above the amplifiers binding posts. For operation in the Mono Mode, a single loudspeaker should be connected to the two RED bindi

38、ng posts only. No connection is made to the amplifiers BLACK binding posts. Connect the speakers RED (+) terminal to the amplifiers RED terminal labelled (+), and the speakers BLACK (-) terminal to the amplifiers RED terminal labelled (-). The polarity symbols (+/-) for the Mono Mode are labelled ab

39、ove the polarity markings for the Stereo Mode. The 9130 Amplifier is equipped with front panel mounted Gain Controls. These controls may be used to attenuate the input signal to the amplifier. The maximum clockwise position of these controls applies the full input signal to the amplifier. Intermedia

40、te positions of these controls will partially attenuate the signal, and the full counter-clockwise position attenuates the input signal completely. Most applications will dictate that these controls be set to their maximum clockwise position. In situations of unusually high level signal sources, or for matching levels in multiple amplifier installa- tions, it may be desirable to use an intermediate position of the Gain Controls. Unless intentionally introducing different gain levels in the two channels of the amplifier, these controls should normally be set at