Denon-AVR3806-avr-sm维修电路原理图.pdf

《Denon-AVR3806-avr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Denon-AVR3806-avr-sm维修电路原理图.pdf（123页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL MODELAVR-3806 AV SURROUND RECEIVER For U.S.A. & Canada model TOKYO ,JAPAN X0253 V.01 DE/CDM 0508 Some illustrations using in this service manual are slightly different from the actual set. Please use this service manual with referring to the operating instructions without fail. For pu

2、rposes of improvement, specifications and design are subject to change without notice. 本文中使用、説明都合上現物 多少異場合。 修理際、必取扱説明書参照上、作業行 。 前、 必読。本機、火災、感電、 対安全性確保、配慮 、法的電気用品安全法 、所定許可得製造。 従際、安全性維 持、記載 注意事項必守。 本機仕様性能改良、予告変更 。 補修用性能部品保有期間、製造打切後8年。 注意 Denon Brand Company, D&M Holdings Inc. Ver. 1 RadioFans.CN 收音机爱

3、好者资料库 2 AVR-3806 / AVC-3920 SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis

4、resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective. (1) (2) 500V 1M (1) (2) RadioFans.CN 收音机爱 好者资料库 3 AVR-3806 / AVC-3920 DIMENSION 0 28.5 182.5 15 0 172 172 217 217 0 66.1 8

5、8.2 244.5 318.1 338.8 4 AVR-3806 / AVC-3920 WIRE ARRANGEMENT If wire bundles are untied or moved to perform adjustment or parts replacement etc.,be sure to rearrange them neatly as they were originally bundled or placed afterward. Otherwise, incorrect arrangement can be a cause of noise generation.

6、Wire arrangement viewed from the top 整形図 調整部品交換等、類結束 移動場合、作業完了時点 整形。正整形 発生原因。 上面整形 Front Panel side Back Panel side 5 AVR-3806 / AVC-3920 CAUTION IN SERVICING Initializing AV SURROUND RECEIVER AV SURROUND RECEIVER initialization should be performed when the com, peripheral parts of com, and Digital

7、P.W.B. are replaced. 1. Switch off the unit. 2. Hold the following NIGHT button and PURE DIRECT button, and switch on the unit. 3. Check that the entire display is flashing with an interval of about 1 second, and release your fingers from the 2 buttons and the microprocessor will be initialized. Not

8、e:If step 3 does not work, start over from step 1. All user settings will be lost and this factory setting will be recovered when this initialization mode. So make sure to memorize your setting for restoring after the initialization. 時注意事項 AV 初期化 周辺部品、Digital 基板等交換場合、 AV 初期化行下。 1. OFF 。 2.NIGHT PURE

9、 DIRECT 同時押、 押 ON 。 3.表示約 1 秒間隔点滅確認後、 2 指離。 初期化。 注意 :上記 3 状態場合、一度操作 1 直。 初期化行客様設定内容工場出荷状 態戻、設定内容控 初期化後再設定。 6 AVR-3806 / AVC-3920 ADJUSTMENT 調整 Audio Section Idling Current (1U-3701-1) Required measurement equipment: DC Voltmeter Preparation (1) Avoid direct blow from an air conditioner or an electri

10、c fan, and adjust the unit at normal room tempereture 15 C 30 C (59 F 86 F). (2) Presetting POWER (Power sourse switch)OFF SPEAKER (Speaker terminal)No load (Do not connect speaker, dummy resistor, etc.) Adjustment (1) Remove top cover and set VR101, VR102, VR201, VR301, VR302, VR401, VR402, on 1U-3

11、701-1 (Power Unit) at fully counterclockwise (). (2) Connect DC Voltmeter to test points (FRONT-Lch: TP30112pin, FRONT-Rch: TP10156pin, CENTER ch: TP30134pin, SURROUND-Lch: TP101 34pin, SURROUND-Rch: TP10112pin, SURROUND BACK-Lch: TP30178pin, SURROUND BACK-Rch: TP30156pin). (3) Connect power cord to

12、 AC Line, and turn power switch ON. (4) Presetting. MASTER VOLUME : - counterclockwise (min.) MODE: 7CH STEREO FUNCTION: CD (5) Allow 2 minutes, and turn VR101 clockwise () to adjust the TEST POINT voltage to 6.5 mV 0.5 mV DC. (6) After 10 minutes from preset, turn VR101 to set the voltage to 8 mV 0

13、.5 mV DC. (7) Adjust the Variable Resistors of other channels in the same way. (8) After 5 minutes from (6), turn VR101 to set the voltage to 8 mV 0.5 mV DC. (9) Adjust the Variable Resistors of other channels in the same way. (1U-3701-1) :DC Voltmeter (1) 1530 (2) OFF () (1)1U-3701-1 VR101, VR102,

14、VR201, VR301, VR302, VR401, VR402 () (2)(FRONT-Lch: TP30112pin, FRONT- Rch: TP10156pin, CENTER ch: TP30134pin, SURROUND-Lch: TP10134pin, SURROUND-Rch: TP10112pin, SURROUND BACK-Lch: TP30178 pin, SURROUND BACK-Rch: TP30156pin)DC Voltmeter (3)AC100V95105V ON (4) ON MASTER VOLUME () SPEAKER MODE : 7CH

15、STEREO FUNCTION : CD (5) 2VR101() 6.5mV 0.5mV DC (6)10VR101 8mV 0.5mV DC (7) (8) (6)5VR101 8mV 0.5mV DC (9) 7 AVR-3806 / AVC-3920 DC Voltmeter VR402 VR401 SBR ch SBL ch VR302 SR ch VR102 FR ch VR101 FL ch C ch VR301 SL ch Audio Section FL ch SR ch SL ch FR ch TP301 C ch SBR ch SBL ch TP101 8 AVR-380

16、6 / AVC-3920 VIDEO Section 1. SETTING (1) Connect the oscilloscope to the Y-signal and C-signal of S MONITOR OUT terminal and each terminate at 75 Ohms. (2) Connect the oscilloscope to the Y-signal, PB-signal and CB-signal, PR-signal and CR-signal of COMPONENT MONITOR OUT2 terminal and each terminat

17、e at 75 Ohms. Use the 75 Ohms resistance must be 1% (3) DVD test disc : DVDT-S01 (4) COMPONENT VIDEO OUT of DVD player is connected to COMPONENT IN-1. 2.BEFORE ADJUSTMENT 2.1. Setting the Oscilloscope as below. (1) PB/CB, PR/CR, C (a) TIME/DIV:10s (b) VOLT/DIV:100mV (Use the probe : x10 ) (2) Y (a)

18、TIME/DIV:10s (b) VOLT/DIV:200mV (Use the probe : x10 ) Power on. Power Supply USA & Canada: 120V Europe: 230V Japan: 100V China & Korea: 220V 2.2. Setup the DVD player and confirmation of the stators (1) Set to INTERLACED mode at the COMPONENT OUT. (2) Confirm the DVD players out put level is equal

19、as the item 2.4. in following. 2.3. Preparation (1) Push POWER button with pressing DIMMER and ROOM EQ buttons. (2) Confirm 0.0dB appearing on the FL display. (3) Turn the FUNCTION knob to select DVD input. (4) Push PURE DIRECT button to select PURE DIRECT. (FL display disappears and becomes adjustm

20、ent mode.) (5) Push OPEN/CLOSE button of DVD player, then open the Disc Tray. Set DVD test disc (DVDT-S01) on the Disc Tray, and then push CLOSE button. (6) DVD player FL display appear STOP, push PLAY but- ton to playback DVD. (7) Push the DISPLAY button of remote control of DVD player unit and the

21、n appear the ON-Screen Display (GUI) on the monitor TV. (8) Push the +10 and 2 button, select Title 12 of DVD. (9) Push the ENTER button, playback Title 12. (color bar 75%) 1. 手順 (1) S MONITOR OUT 端子 Y 信号 C 信号 （終端抵抗：75）接続 。 (2) COMPONENT MONITOR OUT2 端子（Y, PB/CB, PR/CR ）（終端抵抗： 75）接続。 75 抵抗 1品使用事。 (3

22、) DVD ：DVDT-S01 用意。 (4) DVD COMPONENT VIDEO OUT COMPONENT IN-1 接続。 2. 調整 2.1. 下記設定 (1) PB/CB, PR/CR, C (a) TIME/DIV:10s (b) VOLT/DIV:100mV （ x10 使用） (2) Y (a) TIME/DIV:10s (b) VOLT/DIV:200mV （ x10 使用） 電源電圧：100V 2.2. DVD 設定確認 (1) COMPONENT OUT 設定 。 (2) DVD 出力以下 2.4. 合 確認。 2.3. 準備手順 (1) AC 挿入、 DIMMER

23、ROOM EQ押電源 ON 。 (2) FL 表示右上 VOL 表示 0.0dB 確認。 (3) FUNCTION 回、入力 DVD 切替。 (4) PURE DIRECT押、PURE DIRECT 。 （FL 表示消、調整。 ） (5) DVD OPEN/CLOSE押 開、上 DVD （DVDT- S01）後、 CLOSE押。 (6) DVD 表示管上 STOP 表示 、 PLAY押、再生。 (7) DVD DISPLAY押 (GUI) 画 面出。 (8) 番号 +10 ,2押、 Title 12選択 。 (9) ENTER押、Title 12 再生。 （75信号） 9 AVR-3806 /

24、 AVC-3920 2.4. Procedure (1) Adjust the signal of S MONITOR OUT by the wave of os- cilloscope. (a) Target, Y-signal Point:1U-3705 VR601 Adjustment Value:714 14mV Waveform (b) Target, C-signal Point:1U-3705 VR602 Adjustment Value:286 5mV Waveform (2) Adjust the signal of COMPONENT OUT by the wave of

25、oscilloscope. (a) Target, Y-signal Point:1U-3705 VR603 Adjustment Value:714 14mV Waveform (b) Target, PB/CB-signal Point:1U-3705 VR604 Adjustment Value:*525 10mV Waveform Y-signal of S MONITOR OUT Y C C-signal of S-MONITOR OUT Y Y-signal COMPONENT OUT PB/CB-signal COMPONENT OUT PB/CB 2.4. 手順 (1) S M

26、ONITOR OUT 信号 上波高値調整。 (a) Y 信号 調整個所：1U-3705 VR601 調整値： 714 14mV 波形 (b) C 信号 調整個所：1U-3705 VR602 調整値：286 5V 波形 (2) COMPONENT OUT 信号上 波高値調整。 (a) Y 信号 調整個所：1U-3705 VR603 調整値： 714 14V 波形 (b) PB/CB信号 調整個所：1U-3705 VR604 調整値：525 10V 波形 S MONITOR OUT Y 信号 Y C S-MONITOR OUT C 信号 Y COMPONENT OUT Y 信号 PB/CB COM

27、PONENT OUT PB/CB信号 10 AVR-3806 / AVC-3920 (c) PR/CR信号 調整個所：1U-3705 VR605 調整値：525 10V 波形 PR/CR COMPONENT OUT PR/CR信号 (c) Target, PR/CR-signal Point:1U-3705 VR605 Adjustment Value:*525 10mV Waveform * : 486 10mV for U.S.A. & Canada model 1U-3705 DIGITAL UNIT PR/CR-signal COMPONENT OUT PR/CR VR601 S-Y

28、VR602 S-C VR603 Y VR604 PB/CB VR605 PR/CR 11 AVR-3806 / AVC-3920 BLOCK DIAGRAM (1/2) AUDIO BLOCK DIAGRAM 12 AVR-3806 / AVC-3920 BLOCK DIAGRAM (2/2) VIDEO BLOCK DIAGRAM 13 AVR-3806 / AVC-3920 CLOCK FLOW & WAVE FORM IN DIGITAL BLOCK Wave form CH1: D-DATA 1 CH1: DATA CH2: fs CH3: 64fs CH4: 256fs 3 CH1:

29、 DATA CH2: fs CH3: 64fs 2 14 AVR-3806 / AVC-3920 LEVEL DIAGRAMS (1/6) 15 AVR-3806 / AVC-3920 LEVEL DIAGRAMS (2/6) 16 AVR-3806 / AVC-3920 LEVEL DIAGRAMS (3/6) 17 AVR-3806 / AVC-3920 LEVEL DIAGRAMS (4/6) 18 AVR-3806 / AVC-3920 LEVEL DIAGRAMS (5/6) 19 AVR-3806 / AVC-3920 LEVEL DIAGRAMS (6/6) 20 AVR-380

30、6 / AVC-3920 SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. 主半導体記載。汎用半導体記載省略。 Note : Abbreviation ahead of IC No. indicates the name of P.W.B., etc. 注） ：IC No. 前記号、基板名称表。 MA : MAIN CPU UNIT PA : POWER AMP UNIT PS : POWER SUPPLY UNIT FR : FRONT UN

31、IT AV : AUDIO/VIDEO UNIT DI : DIGITAL UNIT 1. ICs M30626 (MA : IC506) M30626F Terminal Function PinPin NameSymbolI/OTypeDet Op (Int.) Op (Ext.) Res ST BY stopFUNCTION 1P96/SOUT4（E_SPIMOEI）OC-ZO/LO/LNot used 2P95/CLK4（E_SPICLK）OC-ZO/LO/LNot used 3P94/TB4（E_SPICS）OC-ZO/LO/LNot used 4P93/TB3ACKSIMOI-Ed

32、ZO/LO/LMAIN-SUB com comm. control pin 5P92/SOUT3MOSIOC-EdZO/LO/LMAIN-SUB com comm. control pin 6P91/SIN3SOMIOC-EdZO/LO/LMAIN-SUB com comm. control pin 7P90/CLK3CLKMOOC-EdZO/LO/LMAIN-SUB com comm. control pin 21 AVR-3806 / AVC-3920 8BYTEBYTE-GND (Ext. data bus bit width switching, 16bit: L) 9CNVCSCNV

33、SSI-Ed-Single-chip/Micro-processor mode switching (Normal single- chip: L,Rewrite boot program start:H input set) 10P87RST SUB(RESET2)OC-EdZO/LO/LSUB-com reset output 11P86（E_RESET）OC-ZO/LO/LNot used 12RESETRESETI-Lv-EuLIIReset input (Reset=L) 13XOUTX2O-Oscillator connection 14VSSVSS-GND 15XINX1I-II

34、Oscillator connection 16VCCVCC-+5V 17P85/NMI_NMII-Not used (Fixed to H) 18P84/INT2B.DOWNI-E &L-EuZIIPower down detect (Power down:L) 19P83/INT1PROTECTIONI-E &L-EdZIIProtection detect input (Detected:L) 20P82/INT0REQSOMII-E &L-IO/LMAIN-SUB com comm. control pin 21P81（EMODE）I-Lv-EuZO/LO/LNot used 22P8

35、0REQ XMI-EdZO/LO/LXM RADIO control pin 23P77FSTB1OC-ZO/LO/LSTB output for function switching control (TC94A46FG) 24P76FSTB2OC-ZO/LO/LSTB output for RECINH/EXT.IN switching control (TC9273N- 015,TC9274N-017) 25P75A.EXPOEOC-EdZO/LO/LAudio expander control pin(TC4094BF) 26P74A.EXPSTBOC-ZO/LO/LAudio exp

36、ander control pin(TC4094BF) 27P73/CTS2A.EXPDOC-ZO/LO/LAudio expander control DATA output pin (TC4094BF) 28P72/CLK2 A.EXPCLKOC-ZO/LO/LAudio expander control CLK output pin (TC4094BF) 29P71/RXD2RXD MIXMOI-ZIO/LXM RADIO control pin 30P70/TXD2TXD MOXMION-EuZO/LO/LXM RADIO control pin 31P67/TXD1TXD MO232

37、IOC-EuZO/LO/LData transfer output to outside(AMX) 32P66/RXD1RXD MI232OI-EdZIO/LData receive input from outside(AMX) 33P65/CLK1VSCLI/OC-EuZIO/LVideo selector control pin (NJW1321) 34P64/CTS1VSDAI/OC-EuZIO/LVideo selector control pin (NJW1321) 35P63/TXD0TXD_iPOD(E_TXDMOEI)OC-ZO/LO/LNot used 36P62/RXD0

38、RXD iPOD(E_RXDMIEO)I-ZO/LO/LNot used 37P61/CLK0E.VOL_CLKOC-ZO/LO/LE-VR control output (TC94A32F,TC9459F) 38P60/CTS0E.VOL_DATAOC-ZO/LO/LE-VR control output (TC94A32F,TC9459F) 39P57E.VOL_STBAOC-ZO/LO/LE-VR control output (TC9459F) 40P56E.VOL_STBBOC-ZO/LO/LE-VR control output (TC94A32F) 41P55/EPMFRASH

39、EPM/MUTE POWERI/O-EuZIIRewrite boot program start:L input set 42P54FUNC CLKOC-ZO/LO/LCLK output fur function switching (TC9274N,TC94A46FG,TC9273N) 43P53FUNC DATAOC-ZO/LO/LDATA output fur function switching (TC9274N,TC94A46FG,TC9273N) 44P52MIC DETI-Lv-EdZO/LO/LMicrophone detect input 45P51STEREOI-Lv-

40、EuZO/LO/LWhen TUNER FM stereo receive: L 46P50/CEFRASH CE/TERST I/O-EdZIIRewrite boot program start: H input set)/Video format detector reset (TE8200PF) 47P47TUNEDI-Lv-EuZO/LO/LTUNER turned detect (Detected:L) 48P46TU STB OC-ZO/LO/LTUNER PLL control pin (LC72131) 49P45TU DOUTI-Lv-EdZIO/LTUNER PLL co

41、ntrol pin (LC72131) 50P44RDS DOUTI-E &L-EuZIO/LRDS data input (LC72720) 51P43TURDS CLKOC-ZO/LO/LPLL & RDS control pin (LC72131 & LC72720) 52P42TURDS DATAOC-ZO/LO/LPLL & RDS control pin (LC72131 & LC72720) 53P41RDS CEOC-ZO/LO/LRDS data output (LC72720) 54P40iPODACKOC-ZO/LO/LNot used 55P37VERSTOC-EdZO

42、/LO/LVideo encoder reset（ADV7320） 56P36VDRSTOC-EdZO/LO/LVideo decoder reset（ADV7403BSTZ-110） 57P35OSD_STBOC-ZO/LO/LMAIN OSD control pin 58P34OSD_CLKOC-ZO/LO/LMAIN OSD control pin 59P33OSD_DATAOC-ZO/LO/LMAIN OSD control pin 60P32OSD_RSTOC-ZO/LO/LMAIN OSD control pin 61P31SYNC.DETI-Lv-EuZIISync. detec

43、t input for MAIN(H: Ext. synchronized) 62VCCVCC-+5V 63P30COMP SDETI-Lv-EuZIO/LMAIN ZONEs COMPONENT signal detect input 64VSSVSS-GND 65P27Z1 VSIG.DETI-Lv-EuZIO/LMAIN ZONEs VIDEO signal detect input （Detected:H) 66P26Z1 SMONIDETI-EuZIO/LMAIN ZONEs S-monitor connection detect input (Connected:L ) 67P25

44、Z1 SSIG.DETI-EuZIO/LMAIN ZONEs S-signal detect input (H: S-signal inputted) 68P24 V.EXPCLKOC-ZO/LO/LCLK output for video expander control (TC4094BF) 69P23V.EXPDOC-ZO/LO/LDATA output for video expander control (TC4094BF) 70P22V.EXPSTBOC-ZO/LO/LSTB output for video expander control (TC4094BF) 71P21V.E

45、XPOEOC-EdZO/LO/LOE output for video expander control (TC4094BF) 72P20POSILOWI-E &L-EdZO/LO/LTemperature detect(Detected:L) 73P17/INT5（EREQ）I-E &L-ZIO/LNot used 74P16/INT4REMOCONI-E &L-ZIIRemote control signal input 75P15/INT3POWER KEYI-E &L-EuZIO/LInterrupt port for WAIT mode cancel 76P14/D12POWEROC

46、-EdZO/LO/LPOWER relay control output (H:ON) 77P13/D11EPOWEROC-EdZO/LO/LETHERNET POWER control output (H:ON) 78P12/D10232C POWEROC-EdZO/HO/L232C POWER control pin (STANDBY:H) 79P11/D9REDLEDOC-EdZO/LO/LPOWER/STANDBY LED control pin PinPin NameSymbolI/OTypeDet Op (Int.) Op (Ext.) Res ST BY stopFUNCTION

47、 22 AVR-3806 / AVC-3920 80P10/D8GRNLEDOC-EdZO/LO/LPOWER/STANDBY LED control pin 81P07/D7H/P DETI-EuZO/LO/LH/P detect input(Detected:H) 82P06/D6FL RSTOC-EdZO/LO/LFL DRIVER control pin 83P05/D5FL CE2OC-ZO/LO/LFL DRIVER control pin 84P04/D4FL CE1OC-ZO/LO/LFL DRIVER control pin 85P03/D3FL DATAOC-ZO/LO/L

48、FL DRIVER control pin 86P02/D2FL CLKOC-ZO/LO/LFL DRIVER control pin 87P01/D1VSEL A I-Lv-EuZO/LO/LMazter Volume rotation detect input（Rotary encoder） 88P00/D0VSEL B I-Lv-EuZO/LO/LMazter Volume rotation detect input（Rotary encoder） 89P107/AN7ISEL AI-Lv-EuZO/LO/LInput selector rotation detect input（Rot

49、ary encoder） 90P106/AN6ISEL BI-Lv-EuZO/LO/LInput selector rotation detect input（Rotary encoder） 91P105/AN5KEY3I-Lv-EuZO/LO/LButton input3 92P104/AN4KEY2I-Lv-EuZO/LO/LButton input2 93P103/AN3KEY1I-Lv-EuZO/LO/LButton input1 94P102/AN2ASIGDETI-Lv-ZO/LO/LSignal detect input 95P101/AN1iPODDETOC-ZO/LO/LNot used 96AVSSA