B&O-BeoSound1-type-25xx维修电路原理图.pdf

《B&O-BeoSound1-type-25xx维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《B&O-BeoSound1-type-25xx维修电路原理图.pdf（89页珍藏版）》请在收音机爱好者资料库上搜索。

1、BeoSound 1 Type 2581, 2582, 2583, 2584, 2585, 2586, 2587, 2590 Service Center repair guide English, German, French, Italian, Spanish RadioFans.CN 收音机爱 好者资料库 1.1 How to service The product has been developed for simple module exchange to follow the On- site service strategy. Module exchange is possib

2、le On-site, at the dealer or in the service workshop whatever is most convenient in each case. For On-site service a Back-up suitcase must be used. Module exchange This way of servicing is recommended, due to the fact that most of the modules are multilayer based, and most of the circuits are on a s

3、ingle main PCB. For On-site service it is possible to order a Back-up suitcase. Microcomputer If the main PCB is replaced, the entire identity of the set is maintained (security code included). If the main PCB is suffering from an intermittent fault, the display can read out error codes in test mode

4、. CD mechanism exchange The CD-PRO II mechanism can be changed on-site or in service centres. Both the CD-mechanism and the servo/decoder PCB are one single unit for easy replacement and future update. There is easy access for cleaning the lens, and by means of test modes most fault symptoms are ide

5、ntifi ed. Turntable gearbox The gearbox which loads the CD is a block module and must be changed as a complete part. FM antenna The antenna module can be replaced on-site. Speakers All speakers can be replaced (placed behind the removable front cover). There is simple sound level adjustment via the

6、display. Amplifi er Part of the main PCB. The only adjustment necessary after module exchange is the speaker sound level. Read out the values for adjustment (in test mode) before replacing the module - if possible. Display fi nd SHIFT in the “list” and then press following sequence: 9 0 2 5 8 After

7、this the product is in test mode and asks for TM no. in two digits on the display. Stop test mode How to stop test mode local Press STANDBY How to stop test mode by IR Beo4 commands V After this the product is out of test mode and in standby. Display “6” looks like “b” in normal mode. In TM HEX fi g

8、ures are used. Therefore the fi gure “6” looks like ”6” in TM. Adjustments, English 5.3 Test modes Master test modes TM 20: Check display (LED). TM 23: Get software version. TM 24: Get service counters. TM 27: Get errors. TM 31: Set default settings. TM 32: Get product ID. TM 43: Get speaker value.

9、TM 44: Set speaker value. Tuner test modes All tuner test modes demands that tuner is selected. TM 00: Select FM frequency. TM 02: Manual offset FM. TM 03: Get offset FM. TM 04: Get variant. TM 07: Store variant. CD test modes All CD test modes demands that CD is selected. TM 61: Focus on. TM 62: Fo

10、cus off. TM 63: Start turntable. TM 64: Stop turntable. TM 65: Move laser out. TM 66: Move laser in. TM 67: Start CD. TM 68: Stop CD. Adjustments, English 5.4 Master test modes TM 20: Check display (LED) Turns on all digits. Used to compare intensity of the LEDs. Press O or STORE to end test mode. T

11、M 23: Get software version APP = application software. After 1.5 sec. the display shows x.xx. Press O or STORE to continue. OS = operation system. After 1.5 sec. the display shows x.xx. Press O or STORE to continue. ra = radio. After 1.5 sec. the display shows x.xx. Press O or STORE to continue. Cd

12、= compact disc. After 1.5 sec. the display shows x.xx. Press O or STORE to end test mode. Note! CD and Radio SW version is only registered if they have been powered on once and CD have to be selected once in TM. TM 24: Get service counters Time for standby, Radio, CD and AUX gives the total “power o

13、n” time. All numbers are stated in interval of 10. (e.g. 3 = 30.) OFF = Standby (hours in standby) After 1.5 sec. the display shows xx.xx. Press O or STORE to continue. ra = Radio (hours in radio mode) After 1.5 sec. the display shows xx.xx. Press O or STORE to continue. Cd = CD (hours in CD mode) A

14、fter 1.5 sec. the display shows xx.xx. Press O or STORE to continue. Au = AUX (hours in AUX mode) After 1.5 sec. the display shows x.xx. Press O or STORE to continue. PrOn = time the theft protection has been enabled. After 1.5 sec. the display shows xx.xx. Press O or STORE to continue. UnLo = numbe

15、r of times the theft protection has been unlocked. After 1.5 sec. the display shows xx.xx. Press O or STORE to continue. On = number of times the product is powered on. After 1.5 sec. the display shows xx.xx. Press O or STORE to end test mode. Adjustments, English 5.5 TM 27: Get errors Get and delet

16、e error info. The last 16 errors are stored. Press N / n or press L / l to toggle between errors. After 1.5 sec the error-code is displayed. 0150 - 0753 : Internal SW-errors. These error-codes are used only for debugging during SW-development. 0A00 - 0A80 : Error on IIC-bus 0 (the fault is on PCB1).

17、 0B00 - 0B80 : Error on IIC-bus 1(the fault is on PCB1 or PCB3). 0C01 - 0C20 : EEPROM error 0D00 - 0D02 : Error in Theft Protection HW 0D03 : Theft Protection functionality not initialized 0D80 : The product has been in the Theft Protection Locked state (PIN-code requested). This is not an error, on

18、ly an information. 0E01 : Primary speaker setup data missing. 0E02 : Primary amplifi er setup data missing. 0E71 : Power supply error 0E72 : Amplifi er error 0F01 - 0F12 : CD-module errors Press O or STORE to display how many errors in all. Press O or STORE to reset errors and end TM, or press T or

19、STOP to store errors and end TM. TM 31: Set default settings Sets default values in NVRAM. Sound values is set to neutral and radio programs are cleared. The test mode ensure that the product is ready for sale. The test mode will not be executed if: The error queue is not cleared/empty. It is possib

20、le to clear all errors by TM 27. The product missing product ID. By TM 32 it is possible to verify product ID. The theft protection is uninitialized, enabled or active (locked). By executing TM 92 it is possible to verify the state of the theft protection. The display will show “run” during the TM a

21、nd if an error occurs the display will show “ Err”. Otherwise the display will show “NoEr” and the TM is ended. TM 32: Get product ID Gets the identifi cation data on the product. Press N / n or press L / l to scroll for viewing hidden digits. A fl ashing digit indicates that there is one or more di

22、gits hidden outside the display. I no = (item number) 7 digits Press O or STORE to continue. Yno = (Type number) 4 digits Press O or STORE to continue. Sno = (Serial number) 8 digits Press O or STORE to continue. Pno = (Theft protection data) Press O or STORE to continue. If the theft protection dat

23、a is OK the display shows “NoEr”. Otherwise the display will show “Err” Press O or STORE to end TM. Adjustments, English 5.6 TM 43 : Get speaker value Shows the sensitivity of a speaker. The value is between -6 dB and 6 dB. The display shows “SPno”. To choose a speaker a digit must be keyed in when

24、display shows “no _”. “no 1” = Left treble speaker “no 2” = Left middle range speaker “no 3” = Bass speaker “no 4” = Right middle range speaker “no 5” = Right treble speaker The display will show a value for the chosen speaker. Press O or STORE to end TM. TM 44 : Set speaker value Sets the sensitivi

25、ty of a speaker. The value have to be between -6 dB and 6 dB. The display shows “SPno” in 1.5 second. To choose a speaker a digit must be keyed in when display shows “no _”. “no 1” = Left treble speaker “no 2” = Left middle range speaker “no 3” = Bass speaker “no 4” = Right middle range speaker “no

26、5” = Right treble speaker Press T or STOP to choose negative dB = “dB - _” or Press O or STORE to choose positive dB = “dB _” Then key in the dB value. Press O or STORE to end TM. Adjustment when replacing the speakerunits Value on the back of the unit Value to store in TM 44 Adjustments, English -3

27、.5 - -2.5 dB -3 -2.4 - -1.5 dB -2 -1.4 - -0.5 dB -1 -0.4 - 0.4 dB 0 0.5 - 1.4 dB 1 1.5 - 2.4 dB 2 2.5 - 3.4 dB 3 5.7 Tuner test modes Beo4 commands; fi nd SHIFT in the “list” and then press following sequence: 9 0 2 5 8 All tuner test modes demands that tuner is selected after those Beo4 commands. T

28、M 00: Select FM frequency If the keyboard is defect it is possible to select an FM frequency in this TM for repair purpose. Key in the frequency-digits and end TM by pressing O. TM 02: Manual offset FM Manual FM offset adjustment. This test mode demands that an FM signal is available. The frequency

29、is determined by the user. Key-in a frequency. The tuner search for this frequency and the offset will be calculated and stored in NVRAM. The display shows “NoEr”. If failure the display shows “Err”. TM 03: Get offset FM Get FM offset. The value X is in steps of 12.5kHz. If the offset-adjustment is

30、needed the display shows ”Err”. If the result of the offset-adjustment is positive the display shows ”0 X” If the result of the offset-adjustment is negative the display shows ”0 -X” Press O or STORE to end TM. TM 04: Get variant Get tuner variant number. (Variant is only registered if the product h

31、ave been in st.by mode) 000 = Error variant 001 = EU variant (FM) 002 = GB variant 003 = USA variant 004 = Japan variant 005 = AUS variant 007 = TWN variant 008 = KOR variant Press O or STORE to end TM. TM 07: Store variant This test mode stores information necessary for the functionality of differe

32、nt tuner variants. To registered the variant change in TM04 the product must be in st.by mode fi rst. Tuner variant setup: If from EU or AUS to US or TWN: Key in the 3 digits indicating the choice. No. 0: 003 = variant US. (007 if TWN). No. 1: 000 No. 2: 175 = FM start (in step of 500 kHz). No. 3: 2

33、16 = FM stop (in step of 500 kHz). No. 4: 075 = Deemphas in s. No. 5: 000 No. 6: 000 No. 7: 000 No. 8: 000 No. 9: 000 Adjustments, English 5.8 If from US or AUS to EU, GB or KOR. No. 0: 001 = variant EU. (002 if GB or 008 if KOR). No. 1: 000 No. 2: 175 = FM start(in step of 500 kHz). No. 3: 216 = FM

34、 stop (in step of 500 kHz). No. 4: 050 = Deemphas in s. No. 5: 000 No. 6: 000 No. 7: 000 No. 8: 000 No. 9: 000 If from EU or US to AUS No. 0: 005 = variant AUS. No. 1: 000 No. 2: 175 = FM start (in step of 500 kHz). No. 3: 216 = FM stop (in step of 500 kHz). No. 4: 050 = Deemphas in s. No. 5: 000 No

35、. 6: 000 No. 7: 000 No. 8: 000 No. 9: 000 Adjustments, English 5.9 CD test modes Beo4 commands; fi nd SHIFT in the “list” and then press following sequence: 9 0 2 5 8 All CD test modes demand that CD is selected after those Beo4 commands. TM 61: Focus ON The CD-pen will try to focus. This TM can onl

36、y be turned off by using TM 62. TM 62: Focus OFF The CD-pen will be turned OFF. TM 63: Starts motor Starts turntable motor. This TM can only be turned off by using TM 64. TM 64: Stops motor Turns off the turntable motor. TM 65: Move laser out Light pen to outermost position. The optical pick-up unit

37、 goes to the outermost position and stays there. This TM can only be turned off by TM 66. Do not give other commands in the meantime. TM 66: Move laser in Light pen to the innermost position. The optical pick-up unit goes to the innermost position and stays there. TM 67: Start CD The CD starts playi

38、ng. This TM can only be turned off by TM 68. Do not give other commands in the meantime. TM 68: Stop CD The CD stops playing. When error in CD-TM the error-number refers to TM 27 CD-errors. Adjustments, English 5.10 REPAIR TIPS Safety mode The product will turn into safety mode if failure in the pow

39、er supply appears or in the amplifi er. (Error 0E71 or 0E72 in TM 27). The standby diode will fl ash in safety mode. Disconnect from mains in 5 sec. to reset the product. Note! In test mode the safety mode is disabled. It may damage the product to restart in TM from safety mode. Exchange of PCB1 and

40、 PCB3 Radio/CD/LF/P module The exchange module PCB1 (Radio/CD/LF/P) contains a special and individual “digital exchange-code” due to theft protection. Therefore if it is not possible to use a PCB1 from an other BeoSound1 during service. It is possible to try out the new module for 12 hours ON-time o

41、r until the PIN code is used. After 12 hours the Radio/CD/LF/P module is named to the product and cannot be used in an other product, because the “digital exchange-code” has been transferred to the P the module and must go back to Bang SHIFT in der “Liste” suchen und dann folgende Sequenz eingeben:

42、9 0 2 5 8 Anschlieend befi ndet sich das Gert im Testmodus und fragt mit zwei Displaystellen nach der TM-Nr. Testmodus beenden Testmodus mit Tasten beenden STANDBY drcken Testmodus mit IR- Beo4-Befehlen V stoppen Anschlieend ist der Testmodus deaktiviert und das Gert im Standby. Display “6” sieht im

43、 Normalmodus wie “6” aus. Im TM werden HEX-Zeichen benutzt. “6” sieht daher im TM wie “6” aus. Einstellungen, Deutsch 5.13Einstellungen, Deutsch Testmodi Haupt-Testmodi TM 20: Display prfen (LED). TM 23: Softwareversion anzeigen. TM 24: Servicezhler anzeigen. TM 27: Fehler anzeigen. TM 31: Voreinste

44、llungen aktivieren. TM 32: Gerte-ID anzeigen. TM 43: Lautsprecherwert anzeigen. TM 44: Lautsprecherwert einstellen. Tuner-Testmodi Fr alle Tuner-Testmodi muss der Tuner gewhlt sein. TM 00: FM-Frequenz whlen. TM 02: Manueller FM-Offset. TM 03: FM-Offset anzeigen. TM 04: Variante anzeigen. TM 07: Vari

45、ante speichern. CD Testmodi Fr alle CD-Testmodi muss CD gewhlt sein. TM 61: Fokus ein. TM 62: Fokus aus. TM 63: Drehteller starten. TM 64: Drehteller stoppen. TM 65: Laser herausfahren. TM 66: Laser einfahren. TM 67: CD starten. TM 68: CD stoppen. 5.14Einstellungen, Deutsch Haupt-Testmodi TM 20: Dis

46、play prfen (LED) Schaltet alle Segmente ein. Dient zum Helligkeitsvergleich der LEDs. O oder STORE zum Beenden des Testmodus drcken. TM 23: Softwareversion anzeigen APP = Anwendungssoftware. Nach 1,5 s zeigt das Display x.xx. O oder STORE zum Fortfahren drcken. OS = Betriebssystem. Nach 1,5 s zeigt

47、das Display x.xx. O oder STORE zum Fortfahren drcken. ra = Radio. Nach 1,5 s zeigt das Display x.xx. O oder STORE zum Fortfahren drcken. Cd = Compact Disc. Nach 1,5 s zeigt das Display x.xx. O oder STORE zum Beenden des Testmodus drcken. Hinweis! Die CD- und Radio-SW-Version wird nur registriert, we

48、nn sie einmal eingeschaltet wurden, und CD muss einmal im TM gewhlt werden. TM 24: Servicezhler anzeigen Zeit fr Standby, Radio, CD und AUX gibt die Gesamt-Einschaltzeit an. Alle Zahlen entsprechen Zehnerwerten (z.B. 3 = 30.) OFF = Standby (Stunden im Standby) Nach 1,5 s zeigt das Display xx.xx. O o

49、der STORE zum Fortfahren drcken. ra = Radio (Stunden im Radiobetrieb) Nach 1,5 s zeigt das Display xx.xx. O oder STORE zum Fortfahren drcken. Cd = CD (Stunden im CD-Betrieb) Nach 1,5 s zeigt das Display xx.xx. O oder STORE zum Fortfahren drcken. Au = AUX (Stunden im AUX-Betrieb) Nach 1,5 s zeigt das Display x.xx. O oder STORE zum Fortfahren drcken. PrOn = Dauer der Aktivierung des Diebstahlschutzes. Nach 1,5 s zeigt das Display xx.xx. O oder STORE zum Fortfahren drcken. UnLo = Anzahl der Deaktivierungen des Diebstahlschutzes. Nach 1,5 s