HarmanKardon-Signature2.1-pwr-sm维修电路原理图.pdf

PA5800/Signature 2.1 Harman Consumer Group 250 Crossways Park Drive Woodbury, N.Y. 11797 1-800 645-7484 A Harman International Company Part No.: 1112-PA5800/2.1 Rev A 7/99 TECHNICAL MANUALTECHNICAL MANUAL Multichannel Power Amplifier RadioFans.CN 1 Multichannel Power AmplifierHarman KardonPA5800 / SIGNATURE 2.1 TABLE OF CONTENTS FEATURES.1 SPECIFICATIONS.2 FRONT PANEL CONTROLS .3 PA5800/Signature 2.1 REAR PANEL CONNECTIONS.4 INSTALLATION.4 OPERATION.6 IDLE CURRENT ADJUSTMENT.6 PA5800/Signature 2.1 TROUBLE SHOOTING.7 PROTECT MODE .7 PA5800 MECHANICAL EXPLODED VIEW .8 PA5800 MECHANICAL PARTS LIST.9 PA5800 PACKING EXPLODED VIEW.9 Signature 2.1 MECHANICAL EXPLODED VIEW .10 Signature 2.1 MECHANICAL PARTS LIST.11 Signature 2.1 PACKING EXPLODED VIEW.11 PA5800 ELECTRICAL PARTS LIST.12 Signature 2.1 ELECTRICAL PARTS LIST.14 PA5800 POWER SWITCH PCB.16 PA5800 POWER AMPLIFIER PCB.17 Signature 2.1 POWER SWITCH/INDICATOR PCB.18 Rev B9 for optimal performance, all strands must be used. Next loosen the knobs of the speaker output terminals far enough so that the cap moves back on its threads past the U-shaped groove at the back end of the terminal. Making certain that you observe polarity by connecting the negative (-) wire to the black terminal and the positive(+) wire to the red terminal, pass the exposed wire through from the top of the slot until the wire is visible from the bottom end. Holding the wire in place, twist the cap back so that the connection is secured. Do not overtighten or use tools, as this may damage the plastic terminal cap or break the delicate wire strands and decrease system performace. Important Note: When making speaker wire connections, be cartain that none of the strands from one lead touch any other lead. This will cause a short circuit and may damage your amplifier or speakers. Damage from short circuits caused in this manner is not covered by the product warranty. Connections may also be made using standard 4mm 0D banana plugs. Before using a banana-type jack, make certain that the plastic screw caps on the PA5800/2.1 are firmly tightened by turning them clockwise until they are snug against the chassis. This will ensure that the maximum surface area of the plug is in contact with the jack. Once the wire has been attached to the banana plug following the plug manufactures instructions, simply insert the banana plug into the hole provided on the rear of the colored screw caps on the terminal posts. Be certain to observe proper polarity. Finally, run the cables to the speaker locations. It is highly recommended that the length of cable connecting any pair of speakers be identical. For example, make certain that the cable length connecting left and right front or left and right rear (surround) speaker is identical, even though one 5 Multichannel Power AmplifierHarman KardonPA5800 / SIGNATURE 2.1 6 8 6 Multichannel Power AmplifierHarman KardonPA5800 / SIGNATURE 2.1 speaker may be physically closer to the amplifier than the other. Do not coil any excess cable, as this may become an inductor that creates frequency response variations in your system. Connect the wire to the speaker, again being certain to observe proper polarity. Remember to connect the negative or black wire to the matching terminal on the speaker. Similarly, the positive or red wire should be connected to the like terminal on the speaker. NOTE: While most speaker manufacturers adhere to an industry standard of using black terminals for negative and red for positive, some manufacturers may not adhere to this configuration. To ensure properly phased connections and optimal performance, consult the identification plate on your speaker terminals, of the speakers manual to verify polarity. If you do not know the polarity of your speaker, ask your dealer or installer for advice before proceeding, or consult the speakers manufacturer. OPERATION The PA5800/2.1 may be operated in either a manual or automatic mode. If the unit is being used in a stand-alone operation you should follow the instructions below for Manual Operation. When the PA5800/2.1 is connected to another compatible device such as the Signature 2.0 or PT2500 tuner, follow the instructions for Automatic Operation. Make sure the power switch is in the off position before plugging in the AC power cord. After all the connections have been made to the amplifiers input jacks and speaker terminals, connect the power cord to an AC outlet. Turn on your source component and receiver/processor first; start with a low volume level to protect your speakers. Manual Operation The LED indicator should be glowing red if the unit is plugged in. Press the front panel switch to turn the unit on. PA5800 - The indicator surrounding the power switch will turn green after a brief pause. Signature 2.1 - The indicator will flash green briefly, and then go out; the front panel will then illuminate to blue. To turn the unit off, press the power switch again. The LED indicator will return to red. Automatic Operation Before proceeding, make certain the connection between the Signature 2.0, PT2500, or other trigger source has been connected properly to the unit following the previous directions. At this point the trigger source should be off. After all cables are connected and the PA5800/2.1 is plugged in, the LED Indicator should be glowing red. Press the power switch and the indicator will turn amber indicating the unit is in the standby mode and ready to turn on when it receives a signal from the triggering device. Finally, turn on your Signature 2.0, PT2500, or other trigger source to turn the PA5800/2.1 on. PA5800 - The indicator surrounding the power switch will turn green after a brief pause. Signature 2.1 - The indicator will flash green briefly, and then go out; the front panel will then illuminate to blue. At the conclusion of your listening session, there is no need to turn the PA5800/2.1 off manually. When the Signature 2.0, PT2500, or other trigger source is turned off, the PA5800/2.1 will return to the standby mode. Important Note: If you will not be using your audio system for an extended period of time, such as a vacation, we recommend turning the PA5800/2.1 off using the power switch. IDLE CURRENT ADJUSTMENT PA5800/Signature 2.1 Locate test points: PA5800 - P75A, P75B, P75C, P75D, P75E Signature 2.1 - P2, P4, P6, P8, P10 These are 2 pin female molex connectors (5 total, 1 per channel) on the MAIN AMPLIFIER PCB. Attach a DC voltmeter (set to a low range) to these points. This is best accomplished by making up a “test plug” using a male molex connector that fits into the one in the unit, with wires attached, for connection to the voltmeter.An alternative method is to use two “mini-grabbers” to attach to the two outer pins on each connection.Warning: Do not accidentally short the two points together with a meter probe during adjustment. Adjustment Points: PA5800 - R70A, R70B, R70C, R70D, R70E Signature 2.1 - R22, R55, R103, R151, R199 Adjust to 25mv across test points, one channel at a time until all channels comply. 7 Multichannel Power AmplifierHarman KardonPA5800 / SIGNATURE 2.1 TROUBLE SHOOTING The items listed below are a brief guide to minor problems that may arise with audio equipment such as the PA5800/2.1. Before taking a unit in for service, you should check to see if any of these hints solve the problem. If these solutions do not rectify the problem or if the problem recurs, contact your dealer or an authorized Harman kardon service depot for assistance. PROBLEMDIAGNOSISTROUBLESHOOTING HINTS Amplifier will not turn on.? Power Switch turned off.? Turn on Power Switch (No Power Light LED) ? Remote trigger cable not? Verify connection of trigger cable at both ends properly connected. Amplifier turns on, but no? Inputs not connected to? Check input connections. audio from one or more channelsproper jack. ? Speakers not connected Properly.? Check speaker connections. ? Improper settings or output levels? Check the settings on your preamp, from processor or controller.processor or controller. Audio plays, then cuts off.? Signature 2.1 - amplifier shorted? Check speaker connections for Short circuit. (LED flashes amber and red). ? PA5800 - amplifier shorted (LED flashes amber) Hum? Signature 2.1 - Objectionable hum? Certain types of half-power light dimmers on the same (coming from unit itself, not fromAC circuit may cause this, or any other electronic device loudspeakers).That introduces DC into the AC circuit the unit is plugged into. Remove offending device; or plug the unit into a different AC circuit. Otherwise: If upon internal inspection the POWER SWITCH PCBdoes not have the designator HA206-0003-C printed on it (near the relays), order this board by part number HA206-0003-C from Harman. PROTECT MODE Input/Output Protection Under some conditions, such as a shorted speaker wire, DC voltage on an input connection or thermal overload, the amplifier will place itself in a “protect mode” to prevent damage to the amplifier. Signature 2.1 When this happens, the LED Power Indicator will flash and alternate between red and amber. PA5800 When this happens, the LED power indicator will flash amber. When this occurs, IMMEDIATELY turn off the unit using the power switch and correct the problem. Then turn the unit back on.If the unit continues to go into protect mode, contact your dealer or installer for assistance. 8 Multichannel Power AmplifierHarman KardonPA5800 / SIGNATURE 2.1 PA5800 MECHANICAL EXPLODED VIEW 108 112 114 113 101 127 110 132 111 129 128 139 116 134 131 127 117 133 113 116 112 109 136 138 116 114 112 135 140 114 104 103118 119 111115 137 G G A G F F D A D B B B D B B C C D 9 Multichannel Power AmplifierHarman KardonPA5800 / SIGNATURE 2.1 PA5800 MECHANICAL PARTS LIST Ref.#Part #DiscriptionQty 101A080-0007-BTRANSFORMER PA5800, 120V, UL SPECS1 A092-0061-0FASTON, F, V, .250X.032X.260, 14-16GA2 103A095-0021-0CORD, 2X16GA, FLAT, 8FT, DOM1 100-0003-0STRAIN RELIEF, 2X16GA, SR-5KN-41 100-0018-0WIRE SADDLE ADH. BASE2 100-0033-0CABLE TIE - PLT 1M-M, SMALL7 100-0126-0HOLDER, CABLE TIE .75” SQUARE ADH.3 105-0009-0INSULATOR TAPE, 3/4”x7 MIL ADH. BACK 111-0101-0BOLT, 4-40, 5/8, PHP, CAD.5 111-2041-0BOLT, 4-40, 1/4, PHP,3 INT STAR WASHER, ZINC 111-3080-0SCREW, 4AB, 1/2, PHP, B.Z.7 111-7011-0WASHER, #4, SPLIT62 111-8061-0TR-BOLTM 4-40, 3/8, PHP, CAD19 111-8081-0TE-BOLT, 4-40, 1/2, PHP, CAD42 112-3080-0SCREW, 6AB, 1/2, PHP, B.Z.5 112-8040-0TR-BOLT, 6-32, 1/4, PHP, B.Z.27 112-8050-0TR-BOLT, 6-32, 5/16, PHP, BO4 115-6003-1NUT, 8MM, HEX, CAD, B.O.1 115-7008-0WASHER, 8MM, BELLEVILE,1 SPRING STEEL 153-0100-0SAFETY LABEL (RISK OF FIRE)1 NORMAL BLOW FU 202-0006-BCABLE ASSY.1 128HA090-0001-APOWER SWITCH BUTTON1 HA090-0002-ALIGHT PIPE INDICATOR1 HA090-0003-ASWITCH SPRING1 HA090-0004-APLASTIC FRONT BODY SUB PANEL1 HA090-0005-ALIGHT SHIELD1 133HA101-0000-AFOOT4 134HA132-0001-AFRONT PANEL ALUMINUM1 135HA132-0002-AHEAT SINK3 136HA132-0003-BFAB, CHASSIS, BASE1 137HA132-0004-AREAR PANEL1 138HA132-0005-BFAB, TOP COVER1 139HA132-0006-BFAB CROSS BRACE1 140HA132-0007-ASINK PLATE1 HA206-0001-BPOWER SWITCH BOARD1 PA5800 PACKING EXPLODED VIEW Ref.#Part #DiscriptionQty 40150-0089-0BAG POLY 24”x30”x3 mil with vent holes1 41150-0103-0BAG POLY 9”x12”x2 mil CLEAR1 42HA160-0000-AOWNERS MANUAL1 43HA160-0001-AWARRANTY SHEET1 44HA160-0002-ACUSTOMER CARD1 45160-0005-0GROUNDING SAFETY SHEET1 46HA151-0001-AFOAM PACK CORNERS8 (4 TOP/4BOTTOM 8 PER SET) 47HA150-0000-ACARTON1 42 43 44 45 47 40 41 46 10 Multichannel Power AmplifierHarman KardonPA5800 / SIGNATURE 2.1 Signature 2.1 MECHANICAL EXPLODED VIEW 204-0001-0 HA132-0015-B HA206-0003-B HA132-0012-B HA132-0009-A DESCRIPTION & PART NO. BOLT 4-40 5/16 PHP CAP 111-D051-0 BOLT 4-40 5/8 PHP CAD 111-0101-0 SCREW 4AB 1/2 PHP B.Z. 111-3080-0 TR-BOLT 4-40 3/8 PHP CAD 111-8051-0 TR-BOLT 4-40 1/2 PHP CAD 111-808101 BOLT 6-32 1/4 PHP, ZINC 112-004D-D DESCRIPTION & PART NO. 112-3080-0 TR-BOLT 6-32 5/16 PHP 80 112-8050-0 WASHER #4 SPILT 111-7011-0 WASHER #6 SPILT ZINC 112-7021-0 STRAIN RELIEF, 16/2, SPT-2,UL,CSA 100-0035-0 POWER CORD, 2x18-16 GA,SPT-2,UL,CSA 095-0002-0 REF. NO. 1 2 3 4 5 6 REF. NO. 7 8 9 10 11 12 HA132-0014-B 105-0009-0 HA132-0016-0 HA206-0002-B H F H B G K K E A B G C D B D E E H G G H F G G H H D D C R I J J E B I B M M HA132-0013-B HA132-0021-A HA132-0010-B 8 4 9 2 9 8 1 8 2 9 8 8 125 128 8 1 9 9 5 9 4 88 8 8 8 2 9 QTY 4 18 5 43 30 4 A QTY 5 27 93 4 12 2 M 3 7 8 11 Multichannel Power AmplifierHarman KardonPA5800 / SIGNATURE 2.1 Ref.#Part #DiscriptionQty A080-0010-ATRANSFORMER SIG 2.1, 120V TO SP1 A080-0011-ATRANSFORMER SIG 2.1, 230V1 A091-0007-0FUSE, 5MM, 0.5A, 125V, FAST, UL, CSA1 A091-0008-0FUSE, 5MM, 5A, 125V, FAST, UL, CSA10 A091-0011-0FUSE, 5MM, 10A, 125V, FAST, UL, CSA1 A092-0061-0FASTON, F, V, .250X.032X.260, 14-16GA1 A092-0068-0FASTON, F, V, .187X.020X.205, 14-16GA1 A093-2500-0HSG, 2MMX7, 26GA, IDC2 A095-1002-0WIRE 26 AWG, BLK, 7 STRAND, UL1061 11 A095-0002-0POWER CORD 16 GAUGE1 100-0011-0STRAIN RELIEF, SPT-2, UL, CSA1 100-0035-0CABLE TIE, BLACK, 4-18 LB10 100-0126-0HOLDER, CABLE TIE .75 SQUARE, ADHE5 101-0002-0FOOT BLACK ANODIZED/RUBBER GASKET4 102-0003-0BUTTON CAP, LOUDNESS, H/K1 105-0009-0INSULATOR TAPE, 3/4X7 MIL ADHESIVE4 111-0051-0BOLT, 4-40, 5/16, PHP, CAD2 111-0061-0BOLT, 4-40, 3/8, PHP, CAD2 111-0101-0BOLT, 4-40, 5/8, PHP, CAD.18 111-3080-0SCREW, 4AB, 1/2, PHP, B.Z.5 111-7011-0WASHER, #4, SPLIT93 111-8061-0TR-BOLT, 4-40, 3/8, PHP, CAD43 111-8081-0TR-BOLT, 4-40, 1/2, PHP, CAD30 112-0040-0BOLT, 6-32, 1/4, PHP, ZINC4 112-3080-0SCREW, 6AB, 1/2, PHP, B.Z.5 112-7001-0WASHER, #6, FLAT, CAD4 112-7021-0WASHER, #6, SPLIT ZINC4 112-8050-0TR-BOLT, 6-32, 5/16, PHP, BO27 Ref.#Part #DiscriptionQty 153-0100-1SAFETY LABEL(RISK OF FIRE), FAST F1 HA132-0009-ASIG 2.1, FIN PLATE28 120-0002-1ALUM .080, 5052-H32, 6.00X5.15 +/-1 HA132-0010-ASIG 2.1 FRONT PANEL, FINISHED1 HA132-0012-BSIG 2.1 CHASSIS1 111-6036-0NUT, PEM, S-440-1 FOR .040 MIN. THK4 112-6009-0STANDOFF, SO-6440-2414 120-0019-0STEEL, 18 GA.EGC .047 48X120 FPR480 HA132-0013-BSIG 2.1 REAR PANEL, 120V1 120-0019-0STEEL, 18 GA.EGC .047 48X120 FPR198 HA132-0014-BSIG 2.1 TOP COVER1 120-0012-0STEEL, 20 GA.036 EGC 48X120615 HA132-0015-BSIG 2.1 CROSS BRACE1 120-0008-0STEEL, 16 GA.EGC. 48X120198 HA132-0016-BSIG 2.1 SINK PLATE1 129-