HarmanKardon-HKTS14-htss-sm维修电路原理图.pdf

harman/kardon SUB-TS14SUB-TS14 (HKTS 14 SUBWOOFER) SERVICE MANUAL harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev1 10/2005 RadioFans.CN CONTENTS BASIC SPECIFICATIONS . . . . . . . . . . . . . . . . 1 DETAILED SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . 2 CONTROLS or whether it has moved: i.e., the speaker that was not working still has no sound and the speaker that was working is still fine. If the problem is in the same place, the source of the problem is most likely with your receiver or amplifier, and you should consult the owners manual for that product for further information. If theproblem has followed the speaker, consult your dealer for further assistance or, if that is not possible, visit our Web site at for further information. If there is no sound from Check all wires and connections between receiver/amplifier and speaker. Make sure all wires are connected. the center speaker:Make sure none of the speaker wires are frayed, cut, punctured or touching other wires. If your receiver/processor is set in Dolby Pro Logic mode, make sure the center speaker is not in phantom mode. If your receiver/processor is set in Dolby Digital or DTS mode, make sure the receiver/processor is configured so that the center speaker is enabled. If the system plays at low Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. volumes but shuts off as Make sure none of the speaker wires are frayed, cut, punctured or touching other wires. volume is increased: If more than one pair of main speakers is being used, check the minimum impedance requirements of your receiver/amplifier. If there is low (or no) bass Make sure the SUB or Line-Level Inputs of the SUB-TS14 subwoofer and SUB or LFE output of your receiver output:or amplifier are properly connected by the RCA-type interconnect cable. If you are using the SUB-TS14s Speaker-Level Inputs , check your speaker cables to make sure they are all connected; that none of the wires are frayed, cut, punctured or touching other wires; and that you have maintained the correct polarity by connecting positive terminals to positive terminals, and negative terminals to negative terminals. Make sure the subwoofer is plugged into an active electrical outlet and its Master Power Switch is switched on to the “” position. Check the speaker setup (bass management) settings in your A/V receiver or processor to make certain that the front, center and surround speakers are configured for “Small,” and that the subwoofer is set for “Yes” or “On.” If there is no sound from Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure the surround speakers:none of the speaker wires are frayed, cut, punctured or touching other wires. Review proper operation of your receiver/processor and its surround sound features. Make sure the movie or TV show you are watching is recorded in a surround sound mode. If it is not, check to see whether your receiver/processor has other surround modes you may use. In Dolby Digital or DTS mode, make sure your receiver/processor is configured so that the surround speakers are enabled. Review the operation of your DVD player and the jacket of your DVD to make sure that the DVD features the desired Dolby Digital or DTS mode, and that you have properly selected that mode using both the DVD players menu and the DVD discs menu. HKTS 14 OM 11/4/03 11:32 AM Page 16 SUB-TS14 SUB-TS14 harman/kardon harman/kardon 10 Test Set Up and Procedure Equipment needed: Function/signal generator/sweep generator Integrated Amplifier Multimeter Speaker cables Initial Control Settings: Power Switch OFF; Filter OFF Level MIN (Full CCW) Phase, Auto/On switches do not matter General Unit Function (UUT = Unit Under Test) 1) From the signal generator, connect one line level (RCA) cable to the Subwoofer Line Level Input jacks L/R on the UUT. Use a Y-cable from a mono source if necessary to connect to both inputs. Do not connect to the single, purple SUB input. 2) Turn on generator; adjust to 60mV, 50 Hz. 3) Plug in UUT; turn the power switch ON. Turn LEVEL control full clockwise (MAX) 4) LED should turn from Amber to Blue (on top of UUT); immediate and vigorous bass response should be heard and felt from port tube opening. 5) Turn off generator, turn LEVEL control full counterclockwise (MIN), and disconnect RCA cable. 6) Connect one pair of speaker cables to Speaker Level input terminal (IN) on UUT. Cables should be connected to an integrated amplifier fed by the signal generator. 7) Turn on generator and adjust so that speaker level input at the amplifier is 1.2V, 50 Hz. Turn LEVEL control full clockwise. 8) LED should turn from Amber to Blue; immediate and vigorous bass response should be heard and felt from the port tube opening. Sweep Function 1) Follow steps 6-8 above, using a sweep generator as a signal source. 2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or any other noises. If any unusual noises are heard, remove woofers and test. Driver Function 1) Remove woofer from cabinet; detach + and - wire clips. 2) Check DC resistance of woofer; it should be 2.8 ohms 10% 3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V. 4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises. SUB-TS14 SUB-TS14 harman/kardon harman/kardon 11 Ref# Description Part Number Qty 1 Amplifier screw 352-AM04020D210 10 2 SUB-TS14 Amplifier Not for Sale 1 3 Port Tube Not for Sale 1 4 SUB-TS14 Cabinet Not for Sale 1 5 Logo 316-AG-00557 1 6 LED Not for Sale 1 7 Grille Not for Sale 1 8 Logo 316-AL-00553 1 9 12 woofer 30PF14FM-DW05 1 10 Woofer screw 352-FM04020D605 8 11 Foot Pad 320-EVA-00057 4 SUB-TS14 SUB-TS14 harman/kardon harman/kardon 12 SUB-TS14 SUB-TS14 harman/kardon harman/kardon 13 (See Mechanical Parts List on Pages 22-23) SUB-TS14 SUB-TS14 harman/kardon harman/kardon 14 SUB-TS14 SUB-TS14 harman/kardon harman/kardon 15 SUB-TS14 SUB-TS14 harman/kardon harman/kardon 16 SUB-TS14 SUB-TS14 harman/kardon harman/kardon 17 SUB-TS14 SUB-TS14 harman/kardon harman/kardon 18 SUB-TS14 120V Electrical parts list Part numberDescriptionQtyReference Designator PREAMP PCB Resistors 110- 12472j52Resistor 4.7K 1/2W 5% CF 52mm 2R201,202 110- 16102j26Resistor 1K 1/6W 5% CF 26mm 4R213,214,215,254 110- 16103j26Resistor 10K 1/6W 5% CF 26mm 18 R209,212,216,217,218,220,221,222,225,228,229,230, 232,235,240,248,260,270 110- 16104j26Resistor 100K 1/6W 5% CF 26mm 3R231,263,266 110- 16105j26Resistor 1M 1/6W 5% CF 26mm 1R259 110- 16122j26Resistor 1.2K 1/6W 5% CF 26mm 1R265 110- 16134j26Resistor 130K 1/6W 5% CF 26mm 1R233 110- 16151j26Resistor 150 1/6W 5% CF 26mm 1R253 110- 16154j26Resistor 150K 1/6W 5% CF 26mm 1R252 110- 16183j26Resistor 18K 1/6W 5% CF 26mm 1R262 110- 16203j26Resistor 20K 1/6W 5% CF 26mm 2R237,238 110- 16205j26Resistor 2M 1/6W 5% CF 26mm 1R257 110- 16223j26Resistor 22K 1/6W 5% CF 26mm 3R247,255,256 110- 16303j26Resistor 30K 1/6W 5% CF 26mm 2R223,224 110- 16472j26Resistor 4.7K 1/6W 5% CF 26mm 3R200,207,258 110- 16473j26Resistor 47K 1/6W 5% CF 26mm 5R219,249,250,251,264 110- 16512j26Resistor 5.1K 1/6W 5% CF 26mm 2R210,211 110- 16622j26Resistor 6.2K 1/6W 5% CF 26mm 1R234 110- 16913j26Resistor 91K 1/6W 5% CF 26mm 4R203,204,205,206 115- h503a102variable Resistor RV16AE- 20B2- 15K- A54- 104(A50K) 1VR201 Capacitors 129- a154j633metallize capacitor 0.15U 63V 5% MSC 2C221,222 129- a224j633metallize capacitor 0.22uF 63V 5% MSC 1C218 130- 2b221k503disc capacitor 220P 50V 10% 12C200,204,205,207,208,210,21,212,214,220,230,237 130- 2b470k503disc capacitor 47P 50V 10% 1C229 130- 2f104z503disc capacitor 0.1U 50V +80/- 20% 8C232,242,244,245,246,252,254,256 132- 183j503mylar capacitor 0.018uF 50V 5% 1C223 132- 223ja03mylar capacitor 0.022uF 100V 5% 1C215 132- 473j503mylar capacitor 0.047U 50V 5% 1C224 132- 563j503mylar capacitor 0.056U 50V 5% 1C216 132- 823j503mylar capacitor 0.082U 50V 5% 1C217 135- 3105m50electrolytic 1U 50V 20% 1C228 135- 3106m50electrolytic 10uF 50V 20% 10C201,202,206,213,219,231,241,243,251,253 135- 3107m16electrolytic 100uF 16V 20% 1C234 135- 3226m50electrolytic 22U 50V 20% 1C225 135- 3227m16electrolytic 220U 16V 20% 1C233 Semiconductors 192- 027c1815grIC 2SC1815GR NPN3Q201,206, 207,208 197- 131n4148diode 1N4148 26mm 11D201,202,203,204,205,206,207,208,214,215,216 199- 15000335zener diode 3.3V 1/2W 52mm 1D213 190- 06m4558dI.C. OPA 4558D DUAL OP- AMP1U203 190- 16tl074cnI.C TL074CN ST QUAD OP- AMP 2U201,202 SUB-TS14 SUB-TS14 harman/kardon harman/kardon 19 Part numberDescriptionQtyReference Designator PREAMP PCB Miscellaneous 162- 503320032 PIN 330mm RED1D209 174- 0rca313vRCA JACK RCA- 313G V/R/W 1JK201 174- 20810360gJACK SPK JK BP 8PIN 1JK202 175- 1b08v01wire connector 8 PIN PITCH=2.0mm 1W202 175- 1c07v01wire connector 7 PIN PITCH=2.5mm 1M201 180- tms7210vSWITCH SLIDE 6PIN MS7210V 3SW201,202,203 MAIN PCB Resistors 110- 14103j26Resistor 10K 1/4W 5% CF 26mm 3R503,504,510 110- 14222j26Resistor 2.2K 1/4W 5% CF 26mm 1R511 110- 14432j26Resistor 4.3K 1/4W 5% CF 26mm 1R506 110- 14472j26Resistor 4.7K 1/4W 5% CF 26mm 1R505 110- 16102j26Resistor 1K 1/6W 5% CF 26mm 1R153 110- 16103j26Resistor 10K 1/6W 5% CF 26mm 10R128,130,149,150,305,306,308,311,314,319 110- 16104j26Resistor 100K 1/6W 5% CF 26mm 3R122,126,307 110- 16153j26Resistor 15K 1/6W 5% CF 26mm 1R107 110- 16182j26Resistor 1.8K 1/6W 5% CF 26mm 1R145 110- 16203j26Resistor 20K 1/6W 5% CF 26mm 1R309 110- 16221j26Resistor 2201/6W 5% CF 26mm 1R144 110- 16222j26Resistor 2.2K 1/6W 5% CF 26mm 1R102 110- 16223j26Resistor 22K 1/6W 5% CF 26mm 1R316 110- 16333j26Resistor 33K 1/6W 5% CF 26mm 1R310 110- 16393j26Resistor 39K 1/6W 5% CF 26mm 1R151 110- 16434j26Resistor 430K 1/6W 5% CF 26mm 1R312 110- 16473j26Resistor 47K 1/6W 5% CF 26mm 2R106,129 110- 16474j26Resistor 470K 1/6W 5% CF 26mm 1R127 110- 16562j26Resistor 5.6K 1/6W 5% CF 26mm 1R152 110- 16621j26Resistor 6201/6W 5% CF 26mm 1R160 110- 16751j26Resistor 7501/6W 5% CF 26mm 1R315 110- 16755j26Resistor 7.5M 1/6W 5% CF 26mm 1R313 116- 161002f26metal film Resistor 10K 1/6w 1% MF 26mm 2R301,303 116- 161202f26metal film Resistor 12.0K 1/6w 1% MF 26mm 1R302 116- 162200f26metal film Resistor 2201/6w 1% MF 26mm 1R317 116- 162202f26metal film Resistor 22.0K 1/6w 1% MF 26mm 1R318 110- 20332jk3Resistor 3.3K 2W 5% 7.5m 1R134 113- 50s68j00cement Resistor 0.0685w 5%1R147 116- 201001jk3xmetal film Resistor 1.00K 2w 5% MF 7.5mm 1R148 116- 304700jk2xmetal film Resistor 4703w 5% MF 10mm 2R501,502 Capacitors 130- 2f104z503disc capacitor 0.1U 50V 10% 6R107,117,122,144,320,322 130- sl101k503disc capacitor 100P 50V SL 10% 3C302,303,306 132- 103j503mylar capacitor 0.01U 50V 5% 2C305,317 132- 103ja03mylar capacitor 0.01uF 100V 5% 2C103,104 132- 104ja03mylar capacitor 0.01uF 100V 5% 3C123,503,504 132- 273ja03mylar capacitor 0.027uF 100V 5% 1C143 SUB-TS14 SUB-TS14 harman/kardon harman/kardon 20 Part numberDescriptionQtyReference Designator MAIN PCB 135- 3106m50electrolytic 10uF 50V 20% 2C319,321 135- 3107m10electrolytic 100U 10V 20% 2C114,115 135- 3107m35electrolytic 100U 35V 20% 2C507,508 135- 3225m50electrolytic 2.2U 50V 20% 1C509 135- 3226m16electrolytic 22U 16V 20% 1C304 135- 3226m50electrolytic 22U 50V 20% 2C505,506 135- 3227m16electrolytic 220U 16V 20% 1C118 135- 3476m16electrolytic 47U 16V 20% 1C318 132- 103kb00mylar capacitor 0.01uF 400V +/- 10% 1C500 138- 5478m80large aluminum 4700uF 80V 20% 85?2C501,502 Semiconductors 192- 027c1815grtransistor 2SC1815GR 5Q108,109,113,301,302 192- 027c2235ytransistor 2SC2235Y 1Q111 192- 028a1015grtransistor 2SA1015GR 3Q101,107,112 192- 1672n5551transistor 2SN5551 2Q114,115 192- 1682n5401transistor 2SN5401 AI- PNP 350V 500mA TO- 921Q503 197- 013n4148diode 100mA 75V SIGNAL 1N4148 7Q102,103,104,105,143,301,302 199- 15000625zener diode 6.2V 1/2W 52mm 1D101 199- 15001605zener diode 16V 1/2W 52mm 1D502 190- 16t1074cnIC TL074CN ST1U301 192- 161tip31ctransistor TIP31C SGS1Q501 192- 162tip32ctransistor TIP32C SGS1Q502 197- 00kbu606gdiode 6A 800V KBU606G1D501 197- 101n4004diode 1n40042D110,504 Miscellaneous 109- 1ttc802j0thermister TTC- 802(JS) NTC1TH1 120- 1000003inductor 10W AI YT- C3104- 005 1CRHW 35478LTB2FB1,2 162- 50129001wire cable assy 120mm AWG28 WHT1W201 171- urwh124drelay RWH- SH- 124D (1600 ohm)1RL1 175- 1d02v01wire connector 2PIN PITH=3.96mm1M100 175- 1d03v01wire connector 3PIN PITH=3.96mm1M500 Power Amp Class D Module part# 012-7500-00022 RECOMMENDED: REPLACE ENTIRE MODULE Resistors 118- 12061001jSMD Resistor 1.00K 1206 5%4R2,11,29,30 118- 12061002jSMD Resistor 10.0K 1206 5%3R7,9,25 118- 120610r0jSMD Resistor 10.0 1206 5% 2R22,23 118- 12061201jSMD Resistor 1.20K 1206 5%16R31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46 118- 12062002jSMD Resistor 20.0K 1206 5%1R26 118- 12062201jSMD Resistor 2.20K 1206 5%3R6,13,16 118- 12062701jSMD Resistor 2.70K 1206 5%1R10 118- 12063000jSMD Resistor 300.0 1206 5% 1R24 118- 12063301jSMD Resistor 3.30K 1206 5%4R14,15,27,28 118- 12063902jSMD Resistor 39.0K 1206 5%1R3 118- 12064700jSMD Resistor 470 1206 5% 1R8 SUB-TS14 SUB-TS14 harman/kardon harman/kardon 21 Part numberDescriptionQtyReference Designator Power Amp Class D Module part# 012-7500-00022 RECOMMENDED: REPLACE ENTIRE MODULE 118- 12064701jSMD Resistor 4.70K 1206 5% 3R1,5,12 118- 12064702jSMD Resistor 47.0K 1206 5% 1R17 118- 12064704jSMD Resistor 4.70M 1206 5% 1R4 118- 120647r0jSMD Resistor 47.0 1206 5% 2R20,21 Capacitors 141- c0101k50SMD Capacitor 100pF 50V 10% 1206 NPO1C4 141