HarmanKardon-DPR1005-avr-sm1维修电路原理图.pdf

harman/kardon DPR1005 DPR2005 DPR1005 DPR2005 DIGITAL PATH AUDIO/VIDEO RECEIVER SERVICE MANUAL CONTENTS NOTICES PLEASE READ FIRST.2 ELECTROSTATICALLY SENSITIVE DEVICES.3 LEAKAGE TESTING.4 DPR1005 SPECIFICATIONS. .5 DPR2005 SPECIFICATIONS. .6 FRONT PANEL CONTROLS.7 REAR PANEL CONNECTIONS.10 MAIN REMOTE CONTROL FUNCTIONS.13 INSTALLATION/CONNECTIONS17 OPERATION.20 TROUBLESHOOTING GUIDE.26 PROCESSOR RESET.26 UNIT EXPLODED VIEWS.27 EXPLODED VIEW PARTS LIST.29 BLOCK DIAGRAM.31 BULLETIN HK2005-03.32 TECH TIP HKTT2003-01.33 CIRCUIT DESCRIPTION.34 D2 GR70/GR120 POWER MODULE.35 DPR1005 MECHANICAL PARTS LIST.51 DPR1005 ELECTRICAL PARTS LIST.52 DPR2005 MECHANICAL PARTS LIST.63 DPR2005 ELECTRICAL PARTS LIST.64 SMPS (Power Supply) Electrical Parts List.75 SEMICONDUCTOR DATA.79 PCB DRAWINGS.103 SCHEMATICS.113 WIRING DIAGRAM.126 PACKAGING.127 harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev1 7/2005 RadioFans.CN IMPORTANT NOTICES IMPORTANT NOTICES DPR1005 and 2005 that are under the two-year warranty period are considered factory service only in the United States. Please have Customers contact harman/kardon directly at (516) 255-4545 to obtain warranty service. This service manual is being made available for units that are no longer under warranty, and products that are serviced outside the U.S. During testing, do not inject an audio signal frequency into the unit higher than 20kHz with no load. Peaking in the output filter can cause the output voltages to exceed the filter capacitor voltage rating in this design. Normal audio program material will not have enough energy to cause problems. Avoid test tones above 20kHz. The following pages 8 - 27, reprinted from the DPR2005 owners manual, are accurate for every feature and operation of both the DPR1005 and DPR2005 with the following exception: The only feature difference between the two models is located in the front accessory jacks. On the 2005 the Front-panel digital coaxial/optical jacks may be used as either Inputs or Outputs. Those same jacks on the 1005 are for Inputs only; therefore there is also a missing indicator light for this function. For an accurate explanation of these jacks, refer to the DPR1005 owners manual. DPR1005/2005 DPR1005/2005 harman/kardon RadioFans.CN Eachprecautioninthismanualshouldbefollowedduringservicing. Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a component identified with , use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably insulated from the supply circuit before retuming the product to the customer. Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and semiconductor chip components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge build-up or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can generate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.) 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together or your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices. CAUTION : DPR1005/DPR2005 harman/kardonPR1005/DPR2005 harman/kardon RadioFans.CN 1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other metal partsintheunit. 2. Be sure that any protective devices such as nonmetallic control knobs, insulating fish- papers,cabinetbacks,adjustmentand compartment covers or shields, isolation resistor-capacitynetworks,mechanical insulators, etc. Which were removed for the servicingareproperlyre-installed. Before returning the unit to the user, perform the following safety checks : 3. Be sure that no shock hazard exists ; check for leakage currentusingSimpsonModel229LeakageTester,standard equipment item No. 21641, RCA Model WT540A or use alternate method asfollows : Plug the power cord directly Into a 120 volt AC receptacle (do not use an Isolation Transformer for this test). Using two clip leads, connect a 1500ohms,10wattResistorparalleledbya0.15uFcapacitor,inserieswithallexposedmetalcabinetpartsandaknownearthground,such as a water pipe or conduit. Use a VTVM or VOM with 1000 ohms per volt, or higher sensitivity to measure the AC voltage drop across the resistor. (See diagram) Move the resistor connection to each exposed metal part having a return path to the chassis (antenna, metal, cabinet,screwheads,knobsandcontrolshafts,escutcheon,etc.)andmeasuretheACvoltagedropacrosstheresistor.(Thistestshouldbe performedwiththe0.35voltRMSormoreisexcessiveandindicatesapotentialshockhazardwhichmustbecorrectedbeforereturningthe unittotheowner. DPR1005/DPR2005 harman/kardonPR1005/DPR2005 harman/kardon 4 250 Crossways Park Drive,Woodbury, New York 11797 2004 Harman International Industries, Incorporated Part No. ZKD0301HA00-9 DPR 1005 TECHNICAL SPECIFICATIONS Audio Section Stereo Mode Continuous Average Power (FTC) 70 Watts per channel, 20Hz20kHz, <0.15% THD, both channels driven into 8 ohms Seven-Channel Surround Modes Power per Individual Channel Front L 5,638,074; 5,640,161; 5,808,574; 5,838,274; 5,854,600; 5,864,311; 5,872,531; and in Australia: 669114. Other patents pending. A-BUS and A-BUS Ready are registered trademarks of Leisure Tech Electronics Pty Ltd Australia. TiVo is a registered trademark of TiVo, Inc. Replay TV is a registered trademark of Digital Networks North America, Inc. TM 5 250 Crossways Park Drive,Woodbury, New York 11797 2004 Harman International Industries, Incorporated Part No. ZKD0401HA00-3 DPR 2005 TECHNICAL SPECIFICATIONS Audio Section Stereo Mode Continuous Average Power (FTC) 120 Watts per channel, 20Hz20kHz, <0.15% THD, both channels driven into 8 ohms Seven-Channel Surround Modes Power per Individual Channel Front L&R channels: 120 Watts per channel <0.15% THD, 20Hz20kHz into 8 ohms Center channel: 120 Watts <0.15% THD, 20Hz20kHz into 8 ohms Surround (L & R Side, L & R back) channels: 120 Watts per channel 96 dB Dynamic Range 90% Efficient Internal heat sink Configurable Audio Processing Treble, Bass, Volume Control, and EQ per channel Dynamic range compression and output limiting Standard 2-wire serial interface controlled via micro controller or remote PC GUI Pure Digital Path 8-channel digital audio inputs (32 -192 kHz, 16-24 bit) are mapped to 7 speaker output channels Graceful Protection and Recovery Short-circuit, thermal, over-current faults Powered Second Zone Dynamic configuration for 7 channels or 5 channels plus stereo second zone. 2-channel analog or independent rate digital input selection for second zone The D2AudioTM GR70 is a fully self-contained 70 watts per channel digital amplifier module. The module enables rapid system design for manufacturers of home theater components. The GR70 contains a high-performance digital switching controller, MOSFET output stages, and high-quality output filter stages. The module is encased in an EMI-shielded package and tested for compliance with agency regulations to assist FCC Class-B, UL, CSA, and CE certification. The GR70 is capable of driving up to 7 channels at 70 watts into an 8-ohm load with all channels driven per FTC specifications. A configurable audio signal processor provides equalization, volume control, tone control, compression, and limiting. A powered second zone allows for a fully independent amplifier zone. The amplifier can be dynamically configured as 7 channels or 5 channels with a stereo second zone. The second zone supports a stereo analog input or a fully independent digital audio input. A separate digital audio output is also provided for the primary channels. D2AUDIO GR70 Complete digital amplifier for home theater components 70 watts/channel Up to 7 channels Pure digital audio signal path 96dB dynamic range Configurable audio processing Powered 2nd Zone 90% efficient Graceful protection and recovery GR70 (DPR1005) DATA SHEETS DPR1005/DPR2005 harman/kardonPR1005/DPR2005 harman/kardon 36 CONSUMER GR70 Data Sheet Aug 26, 2003 v1.82 3SPECIFICATIONS 3.1ABSOLUTE MAXIMUM RATINGS 3SPECIFICATIONS 3.1ABSOLUTE MAXIMUM RATINGS Operation at or beyond the Absolute Maximum Ratings may result in permanent damage. Normal operation outside of the limits defined in this specification is not implied. 3.2ELECTRICAL CHARACTERISTICS3.2ELECTRICAL CHARACTERISTICS TA = 25 C, HV=38V, LV=12V, SV=7.5V, Ground = 0V ParameterConditionMin MaxUnit High Voltage Supply (HV)+38V DC Supply 40V Low Voltage Supply (LV)+12V DC Supply 12.5V Signal Voltage Supply (SV)+7.5V DC Supply 8.0V Digital Input Signal Level1 MCLK, SCLK,LRCLK,SDI4:1, Z2_MCLK, Z2_LRCK, Z2_ SCLK, Z2_SDI, SDA, SCL, /PWRDWN, /RESET, Z2_EN, Z2_AD, MD0, MD1 -0.6 3.90V Analog Input Signal Level2Peak to peak AC voltage 5V Input Current, any pin but supplies +/-10mA Operating Temperature Range 0 50C Storage Temperature Range-20 60C Lead TemperatureSoldering 10 Seconds 300C Mechanical ShockAny Axis non repetitive TBDG Mechanical ShockAny Axis Repetitive TBDG Electrostatic DischargeMachine Model TBDkV Note 1: -0.6V undershoots and 3.9V overshoots allowed for 4ns maximum Note 2: Analog inputs are terminated with 10k ohms to analog ground, then AC coupled internally TABLE 2: Absolute Maximum Ratings SymbolConditionMin Typ MaxUnit VIL 0.8V VIHInputs except /RESET and /PWRDWN 2.0V VIH/RESET and /PWRDWN 3.0V VOH2 mA Load 2.4V VOL2 mA Load 0.4V IL Input Leakage - CMOS pins MCLK, LRCLK, SCLK, SDI, Z2_MCLK, Z2_LRCLK, Z2_SCLK, Z2_SDI +/-10uA IC Input current on digital inputs with resistive pulls - /PWRDWN, /RESET, Z2_EN, Z2_AD_EN, MD0, MD1, SDA, SCL +/-0.4mA RI Analog input resistance - all analog audio inputs 10k Ohms ZSAnalog source output impedance 100Ohms TABLE 3: Electrical Characteristics DPR1005/DPR2005 harman/kardonPR1005/DPR2005 harman/kardon 37 CONSUMER 5 GR70 Data Sheet Aug 26, 2003 v1.82 3.3PERFORMANCE CHARACTERISTICS3.3PERFORMANCE CHARACTERISTICS Resistance load = 8, HV=38V, LV=12V, SV=7.5V 3.4DC POWER REQUIREMENTS 3.4DC POWER REQUIREMENTS TA = 25C, HV=38V, LV=12V, SV=7.5V, Ground = 0V SpecificationConditionMin Typ MaxUnit Output PowerAll channels driven, FTC3 70 70W Frequency Response20 Hz to 24 kHz, at 1W output power -0.5 0.5dB Dynamic Range-60 dB input 1kHz -96dB Output Distortion (THD+N) 20 Hz to 24 kHz, at 1W output power, MPC control bit off 0.12 0.15% Note 3: FTC spec: 30 minute pre-soak at 1/8th power, full power for 5 minutes, all channels driven simultaneously. TABLE 4: Performance Characteristics SymbolDescriptionConditionMin Typ MaxUnit HV4High Voltage Supply 38V +12VDC+12V Supply11.75 12 12.5V +7.5VDC+7.5V Supply7.0 7.5 TBDV TsrHV High Voltage Supply Slew Rate See Chapter 5.8 20V/S HVHigh Voltage Supply All channels at full power output 18 TBDA +12VDC+12V Supply TBD 1.0A +7.5VDC+7.5V Supply TBD 0.85A HVHigh Voltage Supply /PWRDWN asserted TBD TBDA +12VDC+12V Supply TBD 1.0A +7.5VDC+7.5V Supply TBD 0.85A Note 4: The peak current requirement for the HV power supply is dependent on the overall system power output specification. The GR70 is designed to meet FTC power amplifier specifications for a sine wave continuous power measurement with all chan- nels driven. Under normal conditions for most applications, all channels may not need to be driven at full power simultaneously. More typically, the power output requirement is 1/8 to 1/3 of the total amplifier output. However, if the amplifier is allowed to be driven into high distortion (“clipping”), the power supply current may approach 20% more than required for a full scale out- put. It is therefore up to the system designer to determine how much power output the module will be allowed to produce, and hence determine the maximum and average power supply current requirements. TABLE 5: DC Power Requirements Speaker Outputs 1-7 Controller Pwr FET 7 Pwr FET 2 Pwr FET 1 Filter 7 Filter 2 Filter 1 GR Module Driver 7 Driver 2 Driver 1 Digital Audio OutHV Supply ADC 2-Wire