HarmanKardon-AVR146-avr-sm维修电路图 手册.pdf

harman/kardon AVR146 AVR146 5 X 30W 5.1 CHANNEL A/V RECEIVER SERVICE MANUAL CONTENTS ESD WARNING.2 LEAKAGE TESTING.3 BASIC SPECIFICATIONS.4 PACKAGING.5 FRONT PANEL CONTROLS.6 REAR PANEL CONNECTIONS.8 REMOTE CONTROL FUNCTIONS.10 CONNECTIONS/INSTALLATION.13 OPERATION.23 TROUBLESHOOTING GUIDE.29 REMOTE you may need to make adjustments to fit your system. NOTE: Its possible for a source to use none of the connections named for that source. For example, you might connect your DVD player to the Component Video 1 inputs and the Coax 1 digital audio input. However, we will refer to this source as “DVD”, and in Step Five of the Initial Setup section you will program the receiver so that these connections are assigned to the DVD source.When you select “DVD” as your source using the front panel or the remote, the correct connections for your DVD player will be used. We recommend connecting your various sources using the connections shown in Table 2 below in order to simplify programming your receiver and remote control. However, you may connect any device to any source input. AVR146-OM.qxd 2/5/07 3:59 PM Page 21 AVR146 harman/kardonharman/kardon www.freeservicemanuals.infoIts Free www.freeservicemanuals.info RadioFans.CN 22 INSTALLATION Video 1 Source Since this source includes audio and video recording output jacks, it is best suited to a video recorder, such as your VCR or DVR. Referring to Table 2, connect your recorder to the Video 1 Analog Audio inputs and outputs and to any available coaxial or optical digital audio input (and the coax digital audio output). See Figure 19. Use either the Video 1 S-video or composite video input and output if you wish to make recordings. If you dont plan on recording, you may use the Component Video 2 inputs. Figure 19 Video 1 A/V Inputs and Outputs, and Digital Audio Inputs Remember to connect the audio and video outputjacks on your recorder to the Video 1 or digital audio inputjacks on the AVR, and the audio and video inputjacks on your recorder to the Video 1 or digital audio outputjacks on the AVR. NOTE: It isnt possible to make recordings using HDMI or compo- nent video connections. Keep this in mind as you connect other source devices that you may wish to make recordings from. Video 2 Source The Video 2 source is used only for playback.The AVR 146 remote control is programmed to operate many brands and models of cable and satellite television devices, and we recommend connecting your cable or satellite set-top box to this source. Referring to Table 2, connect your set-top box to the Video 2 Analog Audio inputs and to the Optical 1Digital Audio input. If possible, use the Component Video 2 inputs. Otherwise, connect the set-top boxs S-video or composite video output to the matching Video 2 video input. See Figure 20. Figure 20 Video 2 A/V, DIgital Audio and Component Video Inputs NOTE: If you receive your television programming using your TV with an antenna or direct cable connection, connect the TVs analog and optical digital audio outputs (if available) to the Video 3 Analog Audio inputs and to one of the front-panel digital audio inputs.Do notconnect any video output on the television set to any video input on the receiver. See Step Five for information on connecting the receivers video monitor outputs to the television. Video 3 Source The Video 3 source is used only for playback. It is also generally reserved for components that are only temporarily connected to the receiver, such as cameras and game consoles, although the remote is preprogrammed to operate a TV when the Video 3 source is selected. When not in use, you may place the supplied covers over the front- panel Video 3 jacks for a cleaner appearance. Simply snap the covers in place.When you wish to use the jacks, gently press on the left side of each cover to pivot it out for removal. Referring to Table 2, connect your camera or game console to the Video 3 Analog Audio inputs and to either the Coaxial 3 or Optical 3 digital audio input. See Figure 21. If possible, use the Component Video 2 inputs. Otherwise, connect the devices S-video or composite video output to the matching Video 3 video input. Figure 21 Video 3 A/V and Digital Audio Inputs DVD The DVD source is used for a DVD player. If you have a multichannel device, such as a Blu-ray Disc or HD-DVD player, connect it to the DVD source. Referring to Table 2, connect your DVD player to the DVD Analog Audio inputs and to the Coaxial 1 Digital Audio input. If possible, use the Component Video 1 inputs. Otherwise, connect the DVD players S-video or composite video output to the matching DVD video input. See Figure 22. Figure 22 DVD A/V, digital Audio and Component Video Inputs If your DVD player plays high-resolution audio discs such as SACD or DVD-Audio or when an HD-DVD or Blu-ray Disc player is used, connect the 6-channel analog audio outputs on the DVD player to the 6-channel analog audio inputs on the receiver in order to enjoy these discs to their fullest. See Figure 23. Figure 23 6-Channel Analog Audio Inputs AVR146-OM.qxd 2/5/07 3:59 PM Page 22 AVR146 harman/kardonharman/kardon www.freeservicemanuals.infoIts Free www.freeservicemanuals.info RadioFans.CN 23 HDMI 1 Source The HDMI 1 source is used with a device that is capable of outputting digital video through an HDMI connection, such as a DVD, HD-DVD or Blu-ray Disc player or HDTV tuner.The HDMI 1 source is not used with any of the 2-channel analog audio or video inputs on the AVR 146. Since the AVR 146 is not capable of processing either the audio or video signal transmitted via the HDMI connection, you will need to connect the sources coaxial digital audio output to the Coaxial 2 digital audio input on the AVR 146, or use the 6-channel inputs. See Figure 24.You will also need to make sure your video display is HDMI-capable, and for many source devices, the display must be HDCP-compliant (High-Bandwidth Digital Content Protection) in order to display copy-protected materials. The AVR 146 is Simplay HD-verified, for compatibility via the HDMI connection with other Simplay HD-verified products. If your source or video display is equipped with a DVI (Digital Video Interface) input, you may use an HDMI-to-DVI adapter (not included). Figure 24 HDMI and Coaxial 2 Inputs HDMI 2 Source The HDMI 2 source is used with a second device that is capable of outputting digital video through an HDMI connection, such as a DVD, HD-DVD or Blu-ray Disc player.The HDMI 2 source is not used with any of the 2-channel analog audio or video inputs on the AVR 146. Since the AVR 146 is not capable of processing either the audio or video signal transmitted via the HDMI connection, you will need to connect the sources optical digital audio output to the Optical 2 digital audio input on the AVR 146, or use the 6-channel inputs. See Figure 25.You will also need to make sure your video display is HDMI-capable, and for many source devices, the display must be HDCP-compliant (High-Bandwidth Digital Content Protection) in order to display copy-protected materials. If your source or video display is equipped with a DVI (Digital Video Interface) input, you may use an HDMI-to-DVI adapter (not included). Figure 25 HDMI 2 and Optical 2 Inputs CD The CD source is used for a strictly audio device, such as a CD player. Referring to Table 2, connect your CD player to the CD Analog Audio inputs and to any available digital audio input. See Figure 26. Figure 26 CD Audio Inputs and Digital Audio Inputs No video connections are needed. Tape The Tape source is used for audio-only recorders, such as a CDR, MiniDisc or cassette deck. Referring to Table 2, connect your recorder to the Tape Analog Audio inputs and outputs, and to any available digital audio input (and the coax digital audio output). See Figure 27. Figure 27 Tape Audio Inputs and Outputs, and Digital Audio Inputs and Outputs Remember to connect the output jacks on your recorder to the Tape or digital audio inputjacks on the AVR, and the inputjacks on your recorder to the Tape or coax digital audio outputjack on the AVR. No video connections are needed. With Harman Kardons optional The Bridge, you can play audio, video or still images stored on your iPod (not included), use your AVR 146 remote control to operate the iPod, and even charge the iPod while its docked in The Bridge. Simply plug the proprietary cable from The Bridge into the special The Bridge/DMP connector on the rear of the AVR 146. See Figure 28. Refer to the owners manual for The Bridge to select the appropriate insert to match your iPod. Figure 28 The Bridge/DMP Connector Step Five Connect the Video Display Only video connections should be made between the receiver and your video display (TV), unless your TV is the source for your television programming (see Video 2 Source, above). You will need to make a video connection for each type of video used for your sources. In addition, even if you didnt use S-video or composite video for any of your sources, one of these video monitor connections is required to view the AVR 146s on-screen menus and displays. First, determine what types of video your display is capable of handling. Remember that HDMI is preferred, followed by component video, S-video and then composite video. Ideally, this guided you in selecting the video connections for your sources. Next, note which types of video connections you used for your source devices. Make sure you didnt use a better type of video connection for a source than your video display can handle. If so, you will need to disconnect the source and use a video connection thats compatible with your display. The Bridge TM INSTALLATION AVR146-OM.qxd 2/5/07 3:59 PM Page 23 AVR146 harman/kardonharman/kardon www.freeservicemanuals.infoIts Free www.freeservicemanuals.info RadioFans.CN 24 INSTALLATION If you used an HDMI video connection for any of your sources, then connect the HDMI Output on the AVR to an HDMI input on your video display. See Figure 29.As mentioned previously, you will need to make a separate digital audio connection from each source device to the AVR 146, and you will also need to consult the owners guide for your television to learn the proper procedure for disabling or muting the audio. Figure 29 HDMI Output If you used component video for any sources, connect the Component Video Monitor outputs on the receiver to one set of component video inputs on your display. See Figure 30. Make a note of how these inputs are labeled on the display. Figure 30 Component Video Monitor Outputs If you used S-video for any sources, or if all of your sources used HDMI or component video, connect the S-video Monitor output on the receiver to an S-video input on your display. See Figure 31. Make a note of how the input is labeled. If you used composite video for any sources, connect the composite video Monitor output on the receiver to a composite video input on the display. See Figure 31.Again, make a note of how this input is labeled on the display. Figure 31 S-Video and Composite Video Monitor Outputs Consult the manual for your TV to make sure you understand how to select each video input.As you play different source devices that use different types of video connections, select the correct video input on your video display. Step Six Plug in AC Power Having made all of your wiring connections, it is now time to plug each components AC power cord into a working outlet. Before plugging the AVR 146s AC Power Cord into an electrical outlet, make sure that the Master Power Switch on the front panel is popped out so that the word OFF appears on its top. Gently press the button to turn the switch off.This will prevent the possibility of damaging the AVR in case of a transient power surge. Step Seven Insert Batteries in Remote The AVR 146 remote control uses three AAA batteries, which are included. To remove the battery cover located on the back of the remote, firmly press the ridged depression and slide the cover towards the top of the remote. Insert the batteries as shown in Figure 32, making sure to observe the correct polarity. Figure 32 Remote Battery Compartment When using the remote, remember to point the lens toward the front panel of the AVR 146. Make sure no objects, such as furniture, are blocking the remotes path to the receiver. Bright lights, fluorescent lights and plasma video displays may interfere with the remotes functioning. The remote has a range of about 20 feet, depending on the lighting conditions. It may be used at an angle of up to 30 degrees to either side of the AVR. If the remote seems to operate intermittently, or if pressing a button on the remote does not cause the AVR Selector or one of the Input Selectors to light up, then make sure the batteries have been inserted correctly, or replace all three batteries with fresh ones. Step Eight Program Sources Into the Remote The AVR 146 remote not only is capable of controlling the receiver, but it may also be programmed to control many brands and models of VCRs, DVD players, CD players, cable boxes, satellite receivers, cassette decks and TVs, as well as an iPod docked in The Bridge. It may help to think of the remote as a book with pages. Each page represents the button functions for a different device. In order to access the functions for a particular device, you first need to turn to that page, that is, switch the remote to that device mode. This is done by pressing the AVR Button to access the codes that control the receiver, or the Input Selector buttons to access the codes for the devices programmed into the remote. You may have noticed that three of the Input Selectors look different from the others (see Figure 33). For the DVD/CD,TAPE/The Bridge and HDMI 1/HDMI 2 Selectors, there is a primary source, whose name is printed on the button, and a secondary source, whose name is printed in green above the button.To access the code set for the primary source (which also selects that source input on the AVR and turns on the AVR), press the Input Selector once.The Input Selector will light in red to indicate that the primary source is active. To access the code set for the secondary source (which also selects that source input on the AVR and turns on the AVR), press the Input Selector a second time.The Input Selector will light in green to indicate that the secondary source is active. The AVR 146s remote is factory-programmed to control an iPod docked in The Bridge and many Harman Kardon DVD and CD players. If you have other source devices in your system, follow these steps to program the correct codes into the remote. AVR146-OM.qxd 2/5/07 3:59 PM Page 24 AVR146 harman/kardonharman/kardon www.freeservicemanuals.infoIts Free www.freeservicemanuals.info RadioFans.CN INSTALLATION 1. Using the codes in Tables A9A16 of the Appendix, look up the product type (e.g., DVD, cable TV box) and the brand name of y